The efficiency of cleaning depends on the technical condition of your equipment, and Xiaomi is no exception. Over time, even the most powerful turbobrush loses traction, begins to emit unpleasant cracks or simply stops sucking up small debris. The main reason lies in the banal blockage: carpet pile, animal hair and human hair are wound on a rotating shaft, blocking its operation.
Many owners mistakenly believe that it is enough to simply shake the dust container. However, deep cleaning of the nozzle requires more careful approach and compliance with certain rules. Ignoring this process can lead to overheating of the brush engine and the failure of the expensive unit. In this article, we will discuss how to properly and safely maintain the turbobrush of your vacuum cleaner.
Before you start disassembling, you need to make sure that the device is completely off the grid or the battery is removed, which is a basic electrical safety rule that you can't ignore. Preparing the workplace is also important: you need good lighting and a few tools that are available in every home.
Diagnosis of pollution and preparation for cleaning
The first step should always be to visually assess the condition of the device. Turn the nozzle over and carefully examine the area around the shaft. If you see a dense layer of dust or a "roller" from the hair, this is a signal for immediate cleaning. Often the problem is noticeable to the naked eye: the brush is difficult to spin or makes a characteristic buzzing sound.
To do good prevention, you'll need a minimum set of tools, so you don't have to use aggressive chemistry or put electrical parts in water.
- 🔪 Sharp knife or special scissors for brush cleaning (often come with a kit).
- 🧹 Small brush or dry toothbrush to remove fine dust.
- 🧼 Microfiber wipe and warm water for cleaning the case.
- 🔦 Lights to inspect hard-to-reach areas inside the canal.
⚠️ Warning: Never use sharp metal objects (needles, sewers) to pick inside a turbobrush if electrical contacts are visible there. You may damage the wiring or insulation, which will lead to a short circuit.
It is also important to check the condition. HEPA-A filter that is often located in the handle or tail of the nozzle, if it is clogged, the air will not circulate and the debris will not be able to get into the main container.
Step-by-step disassembling the Xiaomi turbobrush
The process of dismantling the cleaning head may vary slightly depending on the model, whether it is the Mijia Vacuum Cleaner G9, G10 or newer versions. However, the general principle remains the same for most devices of the brand, first you need to disconnect the main tube and the nozzle from the vacuum cleaner housing.
Notice the locking mechanisms. At the bottom of the nozzle, there are usually latches or screws. In some models, the lid is removed by turning special locks 90 degrees. Act carefully, without undue effort, so as not to break the plastic locks.
☑️ Algorithm for disassembling nozzles
When you remove the bottom panel, you'll have access to the shaft, some models have a shaft fixed on one side, others have a removable shaft on both sides, and if you see a belt, check it for cracks or stretching, which is a key element in the transmission of rotation from the engine to the brush.
What to do if the lid is not removed?
Hair and pile removal from the shaft
The most time-consuming part of maintenance is cleaning the shaft of coiled hair, which can form a dense mass that barely lets air through, and start by removing large tangles with your hands, gently pulling them out from under the bristles.
To remove hair that fits tightly to the surface of the shaft, use a knife or a special blade. Move the tool along the shaft slots, cutting the fibers. After that, the residue will easily be removed. Don't be afraid to damage the bristles if it is badly worn out, but try not to scratch the shaft itself.
- ✂️ Cut the fibers with a knife along the grooves of the shaft.
- 👐 Pull out the cut parts of your hair with your hands.
- 🌬️ Blow the shaft with compressed air or blow heavily to remove fine dust.
- 🧹 Walk with a dry brush on the ends of the shaft.
Pay special attention to bearings or bushings on which the shaft is rotated. If dust gets stuffed in there, the shaft will rotate with difficulty, putting pressure on the engine, and careful cleaning of these areas will restore balance and smoothness of the ride.
Cleaning of filters and air channels
Beyond the mechanical part, the condition of the filter elements is critical. Xiaomi turbo brushes often use a multi-stage filtration system, the primary filter traps large dust, and the secondary filter (often in the form of a sponge or mesh) catches fine particles.
The filters must be washed under running water without the use of detergents, after washing them must be squeezed carefully and left to dry for at least 24 hours, the use of a wet filter is strictly prohibited, as water can enter the engine or cause mold and unpleasant odor.
| Element | Cleaning method | Frequency | Important nuances |
|---|---|---|---|
| The shaft of the brushes | Mechanical (knife, brush) | Every 1-2 weeks | Remove all the windings to the thread. |
| HEPA-filter | Water flushing + drying | Once a month | Drying for at least 24 hours |
| Motor grid | Dry brushing | Once in 3 months | Don't wet, keep it moisture-free. |
| Body nozzles | Wet wipe. | As pollution progresses | Avoiding water from entering electronics |
The air ducts inside the nozzle also need periodic inspection, where fine dust can accumulate, which eventually turns into a dense plaque, wipe the inner walls with a wet cloth, after turning off all electrical components.
💡
To remove old dust from hard-to-reach areas, you can use a pear to clean the optics or a can of compressed air, which will help blow pollution out of corners where the brush does not reach.
Assembly and performance check
Once all the elements are cleaned and dry, you can start the assembly. Set the shaft in place, making sure it rotates freely by hand. Secure the bottom cover by snapping the locks until the characteristic click. Make sure there are no extra parts or gaps.
Put the filters in your seats. Check the density of all the seals. If the filter is not fully inserted, the vacuum cleaner will not work properly, and some of the dust may be released back into the air or into the engine, which is critical to maintaining hygienic cleaning.
Put the nozzle on the vacuum cleaner and turn it on. Listen to the sound of the work: it should be smooth, without screeching, knocking or intermittent humming. If the turbobrush rotates evenly and the suction has recovered, then the procedure is successful.
⚠️ Warning: If there is a strong vibrational noise after assembly, turn off the device immediately. This may mean that the shaft is inserted incorrectly or there is a foreign object in the mechanism.
Typical errors in service
Even experienced users sometimes make mistakes that can shorten the life of a technology, one of the most common is to try to speed up the drying of filters with a hair dryer or battery, and high temperatures can deform the filter's synthetic fibers, after which it will no longer retain fine dust.
Another mistake is to use oil to lubricate shaft bearings. Xiaomi vacuum cleaners typically use self-lubricating sleeves or bearings that do not require maintenance. Getting oil on plastic or bristles will cause even more dust to stick to them, creating an abrasive mixture.
- ❌ Drying filters on a battery or hair dryer (deformation).
- ❌ Lubrication of moving parts with oil (adhesion of dirt).
- ❌ Use of aggressive solvents for plastic.
- ❌ Assembly of wet components (risk of short circuit).
Also, don't ignore the small cracks in the case, because if the plastic cracks, the leakage is broken, and some of the air will be sucked past the filters, and in such cases, it's better to order a replacement part than to operate a damaged device.
💡
Regular maintenance of the turbobrush prolongs the life of the vacuum cleaner engine and maintains the suction power at the factory level.