Xiaomi headphone repair at home: from diagnosis to complete repair

Xiaomi headphones are some of the most popular accessories due to their value for money, but even they are not immune to breakdowns: one stops working, the sound is distorted, and wireless AirDots refuse to connect. Before you run to a service center or buy new ones, try repairing them yourself. 80% In some cases, the problem is solved for 10-30 minutes at minimum cost.

In this article, we will break down all the typical malfunctions of Xiaomi headphones — from wired Hybrid Pro to wireless AirDots 3 Pro — and show you how to fix them at home. You will learn how to solder a 3.5 mm plug, restore contacts in the wire, replace the speaker or battery in the phone. TWS-It's a little bit like a headphone, and what to do if it's not turning on or charging, and for each method, you can find step-by-step photo instructions, lists of tools you need, and tips on how to avoid errors.

Important: if your headphones are still warranty, self-repair can cancel it, in which case you should contact the official Xiaomi service, but if the warranty period has expired or you are willing to risk it, go ahead!

1. Fault Diagnosis: How to Determine What Has Broken

Before you can take a soldering iron or disassemble the body, you need to know exactly what the problem is, and a mistake at this point can lead to even more serious breakdowns, and here are the key symptoms and their possible causes:

• 🔊 No sound in one or both headphones → Problem with the speaker, wire break (for wired models), oxidation of the plug contacts, malfunction of the Bluetooth module (for wired models) TWS).
• 🎵 Distorted or intermittent sound → Membrane damage speaker, poor contact in soldering, interference from other devices (for wireless devices).
• 🔋 They do not charge or discharge quickly. → Failure of the battery, oxidation of the contacts of the charging case, malfunction of the power controller.
• 📶 Don't connect to Bluetooth → Firmware failure, discharged battery, interference from other devices, antenna malfunction.
• 🛠️ Physical damage (cracks, chips, bare wires) → Mechanical impact, cable inflection, fall.

For accurate diagnosis, use this table:

Professional advice: if you have a multimeter, ring the headphone circuit in resistance mode. Normal resistance speaker — 16-32 Ohm (depends on model) If the instrument is showing 0 Om (short circuit) or ∞ (cliff), the problem is exactly in the wire or dynamics.

⚠️ Note: Do not try to disassemble Xiaomi AirDots headphones without special tools - their body is glued and easily breaks. To begin, try software methods (reset, flashing).

2. repair of wired headphones Xiaomi: soldering plug and wire

Xiaomi wired headphones (such as Mi Hybrid Pro or Mi Basic) most often break in two places: at the plug 3.5 mm or at the site of the split cable, 90% of the time the problem is solved by soldering contacts or replacing the plug.

You'll need:

• 🔧 Stolen iron (power) 20-40 W) with a thin sting
• 🧲 solder and flux (better to use acid-free)
• 🔪 Stationery knife or scalpel
• 📏 Tweezers and magnifiers (for convenience)
• 🎧 New plug 3.5 mm (if the old one is not repairable)

Step-by-step instructions for repairing the plug:

1. Cut the plug at a distance 2-3 See from the base to remove the damaged part.
2. Remove the insulation from the wire (carefully so as not to damage the veins!) Inside you will see 3-4 wires: two for sound (left/right channels), one for microphone (if any) and a common earthen».
3. Clean the ends of the wires and get them soldered.
4. Disassemble the new plug and solder the wires to the contacts: 🔴 Red (right channel) → R 🟢 Green/blue (left channel) → L 🟡 Yellow/copper (earth) → GND 🔵 White/black (microphone) → MIC (if)

Check the chain with a tester, collect a plug and isolate the soldering site with a shrink tube.

Determine which wire is responsible for what (call the tester)

Make sure the soldering iron does not overheat the wires (maximum 300)°C)

Use flux for better solder clutch

Do not confuse polarity when soldering the microphone (if any)

-->

If the problem is not in the plug, but in the fracture of the wire (often at the base of the headphone), act as follows:

1. Find the fracture site by bent the wire at different angles (with a sound or crackling).
2. Carefully cut the insulation on 1-2 cm and find the ragged vein.
3. Connect the wires with soldering or twisting (temporary solution), isolate.

⚠️ Warning: Do not use tape for long-term insulation - it will unstick over time.

💡

If you don't have a soldering iron, you can temporarily connect the wires with a conductive glue (like Permatex), but this solution is short-lived. 1-2 month contact is broken.

Repair of wireless headphones Xiaomi AirDots: disassembly and replacement of the battery

Xiaomi AirDots wireless headphones (including Pro models, SE, 3 Pros break down more often due to a discharged battery or problems with contacts in the charging case.

What you need:

• 🔪 Plastic mediator or guitar mediator (to open the body)
• 🔥 Fryer (for softening glue)
• 🔋 New battery (e.g., new battery, BL-5B for AirDots Pro)
• 🧲 soldering iron with a thin sting
• 📸 loope USB-microscope (for working with small details)

How to unpack an earpiece:

1. Heat the body with a hair dryer (temperature) 60-80°C) during 1-2 minutes to soften the glue.
2. Carefully insert the mediator between the front and back of the case, starting from where there are no buttons or microphones.
3. Separate the halves, trying not to damage the plume speaker.

If the headphone is not charging, check:

• 🔋 Battery: Is it swelling or not holding the charge? Need a replacement.
• 🔌 Contacts - oxidized or contaminated? Clean with alcohol.
• 📱 Charging controller – if after replacing the battery, the headphone still does not charge, the problem is in it.

Battery replacement:

1. Solder off the old battery by heating the contacts with a soldering iron (do not overheat!).
2. Salt a new battery, observing the polarity (+ and −).
3. Check the voltage with a multimeter - it should be 3.7-4.2 V.
4. Collect the body using glue B-7000 double-sided.

In headphones Xiaomi AirDots 3 Pro uses a battery type 301230 capacity of 55 mAh. Do not buy cheap analogues – they may swell or not hold charge.

4. Sound recovery: speaker replacement and membrane cleaning

If Xiaomi headphones have lost sound or distortion, the speaker is to blame. In wired models, it can be replaced, in wireless ones, sometimes it is enough to clean.

Causes of failure of the speaker:

• 🔊 Membrane rupture – due to loud sound or mechanical damage.
• 🧲 Oxidation of contacts - especially important after moisture.
• 🔥 Coil burnout – if the headphones were connected to an overly powerful amplifier.

How to Clean the Speaker (for the first time) TWS-headphone):

1. Disassemble the body (see the instructions in the previous section).
2. Remove the safety net from the speaker (carefully, it is fragile!).
3. Remove dust and dirt with a soft brush or compressed air.
4. If the membrane is torn, it can be temporarily “glued” with cyanoacrylate glue (but this is a short-lived solution).

Replacement of the speaker in wired headphones:

1. Buy a speaker of the same size and resistance (for example, 13.5 mm, 32 Ohms will work for the Mi Hybrid).
2. Solve the old speaker from the wires, remembering the polarity.
3. Seal a new speaker while observing polarity (+ ce +, − ce −).
4. Check the sound before final assembly.

For Xiaomi AirDots models, it is more difficult to replace the speaker — it is soldered to the board. If you are not sure about your soldering skills, you should contact the service.

💡

If the speaker is quieter or there is interference after the replacement, check the soldering quality, possibly a poor contact or short circuit somewhere.

5. Software failures: resetting and flashing wireless headphones

Sometimes Xiaomi headphones stop working not because of hardware, but because of software problems.

• 📱 They don’t connect to the phone, although there is a charge.
• 🔊 The sound is interrupted or "stuttered».
• 🔋 They are quickly discharged for no apparent reason.

How to reset settings (for AirDots and similar models):

1. Put the headphones in the charger case.
2. Press and hold the button on the case for 10-15 seconds until the indicator starts flashing red and white.
3. Take out the headphones and try to reconnect.

Flip-through (for advanced users):

If the reset didn’t help, you can try updating the firmware through the official Mi Home or Xiaomi Wear app:

1. Install the application on your smartphone.
2. Connect the headphones and check for updates in the Devices section → Headphones → Update of the PO.
3. If an update is available, follow the instructions on the screen.

⚠️ Warning: Don't interrupt the firmware update process! If the headphones run out or the connection is interrupted, they can turn into a brick. Charge them to 100% before starting.

For models AirDots Pro 2 and later there are unofficial firmware that can be installed through the ADB. However, it is risky – you can lose the warranty or completely break the device.

Repair of the charging case: restoration of contacts and battery replacement

The charge case is a weak point of Xiaomi wireless headphones. Over time, its contacts become oxidized, the battery loses capacity, or the indication stops working.

Typical case problems:

• 🔋 It does not charge the headphones, although it is charged from USB.
• 💡 Charge indicator is off.
• 🔌 Not determined when connecting to the phone.

How to fix contacts:

1. Open the case and inspect the metal contacts (usually 4: two for charging, two for data transfer).
2. If they are oxidized, clean them with a cotton swab with alcohol or a swallow.
3. If the contacts are bent, carefully align them with tweezers.

Replacement of the battery in the case:

1. Disassemble the case, heating it with a hairdryer (similar to disassembling headphones).
2. Disconnect the old battery (usually a lithium cell) 3.7 V, 300-500 mic).
3. Sell a new battery while observing polarity.
4. Check the operation of the case before the final assembly.

If the case is not charged from USB, problem USB-It's easier to buy a new case, and it's more expensive to repair it.

7. Breakdown prevention: how to prolong the life of headphones Xiaomi

To avoid having to fix your headphones every six months, follow these tips:

• 🎧 Store correctly - do not throw headphones into a bag without a case, do not wind the wire tightly onto the device.
• 🚿 Avoid moisture, even if the model has protection. IPX4, Do not wash your headphones under the faucet.
• 🔋 Charge correctly - do not leave your headphones on charging more 2-3 Use the original cable for hours.
• 📵 Don’t overload – don’t turn on the maximum volume for a long time, it spoils the speakers.
• 🧼 Clean regularly – remove earwax and dust with a soft brush.

For wireless models:

• 📱 Update your firmware through Mi Home – this fixes bugs and improves stability.
• 🔄 Reset your settings periodically (once in a row) 3-6 months) to avoid software glitches.
• 🔋 Store in a case – this protects against dust and mechanical damage.

What kills headphones the fastest:

• ❌ Wire inflection at the base of the plug or earphone.
• ❌ Charging with left-hand adapters with inappropriate voltage.
• ❌ Falls and shocks (especially for the TWS-headphone).
• ❌ Prolonged exposure to high temperatures (for example, leaving in the car in the sun).

💡

The most common reason for Xiaomi wired headphones to break is a wire break at the plug. To avoid this, use a 3.5 mm angle adapter or a smartphone case with a notch under the plug.

FAQ: Answers to Frequent Questions