Owners of smartphones Xiaomi Mi 4A They often have to access the interior of the device, and most often, they need to be replaced. SIM-card or memory card, because the tray in this model has a specific design, but sometimes there is a need for more in-depth intervention, for example, to replace the battery or fix hardware malfunctions.
The process of opening the case requires caution and understanding the design of the gadget. Wrong actions can damage the plumes or chipped plastic. In this article, we will discuss in detail how to open the Xiaomi 4A safely, what tools you will need and what nuances you should pay special attention to.
Before you start dismantling, you need to make sure you have the right tools, and using inappropriate items like knives or thick needles increases your risk of injury and damage to your device, and we'll take a standardized algorithm that allows you to complete the task without undue complications.
Preparations for the dismantling of the hull
Before any electronics work is done, it is critical to prepare the workplace, you will need a clean, well-lit surface that will not have any pile or small parts that can get lost, and you will also need to turn off the device completely to avoid short circuits in case of accidental contact with the board.
You'll need special tools to work, which you can buy from radio parts stores or order online. Using improvised tools often leads to the failure of screw threads or scratches on the case.
- 🔧 Plastic blade (mediator) for accurate snapping of latches.
- 🔧 Thin metal needle or paper clip to remove tray SIM.
- 🔧 A set of screwdrivers (usually a cross Phillips #00 or #000).
- 🔧 Suction cup for gently lifting the cover (optional).
Make sure your hands are dry and have no traces of grease or moisture.Static electricity can harm chips, so touching a grounded metal object is recommended before work.
Access to SIM and microSD slots
The most common reason a user needs to open a Xiaomi Mi 4A is to install a SIM card. Unlike many modern models, it uses a combined tray or a specific opening mechanism that depends on the regional version.
To remove the tray, find a round hole next to the USB-Carefully insert the paper clip perpendicular to the body and press until the characteristic click.
⚠️ Attention: Do not use excessive force when pressing the extraction mechanism. If the tray does not come out, check if you hold the tool correctly.
If your goal is to replace the SIM, no further disassembly is required, however, if the tray is stuck or you need to clean the dust connector, you may need to remove the back cover. In some versions of the Mi 4A, the memory card is installed under the removable panel.
Removal of the back cover of the smartphone
The Xiaomi Mi 4A rear panel is fixed to plastic latches around the perimeter of the body, which is harder to remove than in models with a removable battery, but it is real without a hairdryer heating, if you act carefully. Start at the bottom corner, where the charging connector is.
Put a plastic blade or a mediator in the junction between the frame and the lid. Smoothly, without jerking, drive the tool along the side face, gradually snapping the clips, you hear the characteristic crackling — it's normal.
- 📱 Move from the bottom corner up the long side.
- 📱 Walk down the bottom end and then go up the second side.
- 📱 Be careful in the upper part - there may be plumes.
Don’t try to tamper with your nails – you risk breaking them or damaging the texture of the plastic.If the lid sits very tightly, you can slightly warm the perimeter with a hairdryer at a minimum temperature, but for the Mi 4A this is usually not required, since the glue is used minimally.
☑️ Check before removing the lid
Disconnection of plumes and access to components
Once the back cover is removed, you will have access to the main board, the battery and the speakers, and the rule at this point is not to pull the wires and the plumes, they can be glued or tightly fixed.
The first thing you do is turn off the battery, find the battery connector on the motherboard, and gently snap it off with a plastic blade, and this will turn the device off and keep you safe when you do more manipulation.
If your goal is to change the screen or to do a deep cleaning, you may need to unscrew the screws that hold the metal screen of the board, usually about 4-6 pieces. Use a magnetic screwdriver to avoid dropping the screws inside the case.
| Component | Location. | Type of attachment | Caution. |
|---|---|---|---|
| Battery | The bottom part | Plate + glue | Tall. |
| Basic fee | Upper part | Screws + plumes | Critical |
| Camera. | Centre/Upper | schleife | Medium |
| Dynamician | Niz (under pay) | Screws + connector | Low. |
When working with a camera or display plume, use tweezers with wide sponges, grabbing only the hard part of the connector. It is forbidden to bend the wires themselves - this will lead to a break in the contacts.
What to do if the plume does not unfasten?
Battery replacement and maintenance
The battery in the Xiaomi Mi 4A is often based on double-sided tape. Don't use metal objects to extract it that can pierce the lithium polymer cell.
The best way to remove an old battery is to use a thin plastic card or a special tape with adhesive layer, so you can pull the edge of the battery and, as you do the sawing movements, separate it from the body.
⚠️ Warning: If the battery is swelling, handle it very carefully. Do not press on it or pierce it. Dispose of damaged batteries at special reception points.
When installing a new battery, be sure to degrease the seat with alcohol and apply a new layer of glue or bilateral tape. This will prevent backlash and rattling of the smartphone when working.
💡
Use isopropyl alcohol to clean the contacts, and it evaporates quickly and leaves no trace, unlike water or other solvents.
Device assembly and inspection
The assembly is done in reverse order. First, connect the battery plume to the board, then install all the metal screens and twist the screws, make sure that no plume is squeezed and lies in its channels.
The back cover is placed in place with a slight perimeter tap. Start at the top, then snap the side faces and at the bottom end. You should hear a uniform click all over the circuit.
After assembly, turn on the device and check the basic functions:
- 📶 Is the network working and is visible? SIM-map.
- 🔊 Is the sound played through the speaker.
- 📷 Does the camera take a photo (check the focus).
- 🔋 Is the battery charge correctly displayed.
If you've assembled a phone but it's not turning on, don't panic. You may have forgotten to plug in the battery connector or you've inserted a bad display plume. Disassemble the device again and double-check all connections.
💡
Quality assembly depends on the correct order of connection of the plumes: first the battery, then check the inclusion, and only then the final installation of the cover.