How to open and disassemble Xiaomi RedmiBook Pro 8 laptop: instructions with photos and tips

Disassembling the Xiaomi RedmiBook Pro 8 laptop is a task that every owner sooner or later faces. RAM, replace a failing SSD, clean the cooling system, or repair a damaged keyboard, understanding the disassembly process is crucial. Unlike smartphones, laptops have more complex internal structures, and one wrong move can lead to damaged cables, broken clips, or even a non-functional device.

In this article, we will discuss how to safely open the RedmiBook Pro 8 case, what tools you will need, and what to look for to avoid damaging fragile components. We will also look at the typical mistakes that beginners make, and give recommendations for reverse assembly. If you have never disassembled a laptop before, don’t worry: with the right approach, the process is no more difficult than replacing a battery in a smartphone.

⚠️ Important: Disassembly of Xiaomi laptop can lead to loss of warranty if the device is still in warranty service. Before starting work, check the warranty status in the Mi Account application or on the Xiaomi website.

Training: tools and materials

Before you start disassembling, make sure you have everything you need, and the lack of the right tools is the main cause of damage to the body or internal components, and here is the minimum kit you'll need:

• 🔧 A set of screwdrivers with a magnetic tip (required) PH0 and T5 Xiaomi screws)
• 📱 Plastic mediators or shoulder blades (to separate the cover without scratches)
• 🧲 Antistatic bracelet (protection against static electricity)
• 📦 Containers for screws (so as not to confuse mounts of different sizes)
• 🔍 Loop or flashlight (to inspect small connectors)

If you are planning to clean the cooling system, additionally prepare:

• 🌬️ Compressed air cylinder (to remove dust)
• 🧴 Thermopaste (e.g. Arctic) MX-6 processor-substitute)
• 🧻 Lickless wipes and isopropyl alcohol (for cleaning contacts)

⚠️ Warning: Don't use metal tools to separate the lid, it's almost guaranteed to cause chips or cracks on the plastic. Even if you see it in a YouTube video, the risk of damage is too high.

2. Power outage and rear cover removal

The first and most critical step is to completely shut down the device, and even if the laptop is turned off, the capacitors on the motherboard can retain charge, which will short-circuit the device when it is accidentally touched.

Step-by-step:

1. Turn off the laptop through the Start menu → Completion of work.
2. Disconnect the charger.
3. Turn your laptop over and take off the battery (if the model supports a removable battery). The RedmiBook Pro 8 has a soldered battery, so this step is skipped.
4. Press the power button on 15-20 second-discharge.

Now you can start removing the back cover. In RedmiBook Pro 8, it is mounted on 10 screws (8 short and 2 long hinges) and fixed with plastic latches around the perimeter. Carefully unscrew all the screws and fold them into a container, remembering the location.

For the lid separation:

1. Insert a plastic mediator into the gap between the lid and the case at one of the corners.
2. Carefully lead the mediator along the edge, alternately clicking clips (you will hear characteristic clicks).
3. Do not apply force - if the lid does not lend itself, check if all screws are unscrewed.

Power is turned off and the battery is removed (if possible)|

All the screws of the back cover are unscrewed and laid out in containers.|

Only plastic tools are used to separate the cover.|

An antistatic bracelet is worn (or you touch a metal case to discharge statics)|

Access to internal components

Once the lid is removed, you will see the internal layout of the RedmiBook Pro 8.

• 🖥️ RAM (2 slots) SO-DIMM DDR4, maximum 32GB)
• 💾 NVMe SSD (slot M.2 2280, supports PCIe 4.0)
• 🔋 Battery (plain, replacement requires soldering)
• 🌀 Cooler and radiator (mounted) 4 screws, heatpaste on CPU/GPU)
• 📡 Wi-Fi/Bluetooth module M.2 2230)

Warning about warranty seals: In some versions of the RedmiBook Pro 8 on cooler screws or SSD There may be stickers that will void the warranty if your laptop is still warranty, weigh the risks before continuing.

To replace RAM or SSD:

1. Disconnect the battery plume (if you plan to work with the motherboard).
2. For RAM: squeeze the latches on the sides of the module and remove it at an angle of 30°.
3. For SSD: unscrew the screw of fixation and carefully pull the drive behind the edges.

Cleaning of the cooling system

One of the most common reasons RedmiBook Pro 8 disassembly is overheating due to a dust-filled ventilation system. If the laptop starts to make noise, troitlite or turns off under load, it's time to clean the cooler.

Step-by-step process:

1. Unscrew the 4 screws that fix the radiator (usually they are marked with C on the board).
2. Carefully remove the radiator without pulling - the thermopaste can hold it in place.
3. Remove the old thermopaste from the processor and graphics chip with a lilac-free napkin dipped in isopropyl alcohol.
4. Blow the fan blades with compressed air (hold the balloon vertically to avoid liquid ejection!).
5. Apply the new thermopaste with a thin layer (about the size of a pea) on CPU and GPU.

⚠️ Warning: Do not use a vacuum cleaner to clean your laptop, which creates static electricity and can damage components. Also avoid touching the radiator with your bare hands - skin fat impairs thermal conductivity.

The critical detail: in RedmiBook Pro 8 The heat pads on the memory chips are often glued to the radiator. When removing the radiator, they are easy to tear - buy a replacement in advance (thickness). 1-1.5 mm).

💡

If the laptop still overheats after cleaning, check it out. BIOS-Some Xiaomi firmware has Performance mode enabled by default, which accelerates the processor to extreme temperatures. MIUI Control Center (if you have a firmware with support).

5. Battery replacement (for power users)

The battery in the RedmiBook Pro 8 is soldered into the motherboard, so replacing it requires rationing experience and specialized equipment. SMD-Components, it is better to contact the service.

What will be required for replacement:

• 🔥 Temperature-adjusted soldering station (maximum 350)°C)
• 🧵 Seed removal braid or vacuum pump
• 🔋 New battery (original artwork. MB-BAT-008 analogue)
• 🛡️ Heat-resistant Scotch for Contact Isolation

Replacement process:

1. Disconnect the touchpad and keyboard plumes.
2. Carefully unfurl the contacts of the old battery, avoiding overheating of the board.
3. Install a new battery, solder contacts and insulate them with tape.
4. Check the voltage on the contacts with a multimeter (should be) ~3.7V jar-driven).

⚠️ Warning: Incorrect soldering can cause the battery to burn.If the laptop does not turn on after replacing, immediately disconnect the battery and check the power circuit for short circuit.

6. Reverse assembly and performance check

The assembly of the laptop should take place in reverse order, but taking into account several nuances:

• Check that all the plumes (keyboards, touchpad, display) are tightly connected.
• Make sure the screws are twisted with the right force – the overstretched mounts can damage the board.
• Before final assembly, turn on the laptop with the connected charger to check POST (loading BIOS).

Typical errors in assembly:

After successful assembly:

1. Launch your laptop and check all ports (USB, HDMI, audio jack).
2. Make sure the cooler is turned on when loaded (can be checked at HWMonitor).
3. If you've replaced SSD or the scoring, check their display in BIOS Windows.

1. connection of the battery (if disconnected).

2. the density of the adjoining memory (try to reinstall the modules).

3. Contacts the power button (sometimes the plume goes away).

In 80% of cases, the problem is solved by re-disassembly and checking connections.-->

FAQ: Frequent questions about RedmiBook Pro 8