Modern smartphones, including the popular Xiaomi Redmi 9A, are designed to be monolithic, often making it difficult to access internal components without special skills. Owners face the need to open the device when replacing a broken display, a worn-out battery or repairing the bottom charging plume. Disassembly of the case is the first and most critical stage of any repair, the quality of which depends on the future of the gadget.
Mishandling plastic latches or excessive effort when peeling off the back cover can lead to permanent damage to the frame and the appearance of backlashes. In this article, we will discuss in detail the process of how to safely open the Redmi 9A case, what tools will be required and what nuances should be paid special attention to avoid damaging fragile plumes.
Before you get to work, it’s important to understand that the Redmi 9A back cover is attached to a very powerful layer of glue around the perimeter, not just the edges as in older models.This requires careful workspace preparation and good lighting, as any wrong jerk can be fatal to the integrity of the device.
Tools and workplace preparation required
To successfully perform the autopsy procedure, you will need a specialized set of tools that minimize the risks of damage to the body. The use of improvised tools such as knives or pins is strongly discouraged, as they can damage internal components or leave deep scratches on the frame.
- 🔥 A dryer or heating pad (thermophene) to soften the adhesive layer under the back cover.
- 🔧 Set of screwdrivers (mandatory presence of cross-haired) P2 and P0 charge-pen).
- 🃏 Plastic spatula (mediator) or suction cup for gently detaching the cover.
- 🧲 Magnetic mat for sorting screws, so as not to confuse them when assembling.
- 🧴 Isopropyl alcohol or special liquid B-7000 sealing.
Prepare a flat surface with good antistatic coating or just a clean table covered with soft cloth, which will prevent the loss of small screws and protect the screen from scratches during operation, also make sure that you have enough space to place all the tools at hand.
⚠️ Warning: Before starting any work, be sure to turn off the device. If the phone does not turn on due to damage, try to discharge the battery as much as possible before heating to reduce the risk of ignition in case of an accidental puncture.
Pay special attention to the choice of blades. Metal tools can not be used, because they conduct current and can cause a short circuit on the board if you accidentally touch contacts. Plastic in this regard is safe and flexible, allowing you to penetrate narrow gaps without breaking the plastic latches of the case.
Removal of the back cover and deactivation of the plumes
The first step in the process of opening the Xiaomi Redmi 9A case is heating the perimeter of the device. The glue that holds the lid at room temperature is very hard, and trying to remove the lid to the cold is almost guaranteed to destroy it.
Heat the edges of the phone with a hair dryer for 2-3 minutes, constantly moving the air flow so as not to overheat the display matrix or internal components. The heating temperature should not be extreme, just warm the body to a state where it is comfortable to hold in your hand, but the glue will become elastic.
Temperature regime
Once warmed up, use a suction cup to create a small gap at the bottom of the phone, and gently insert a plastic spatula. Drive the tool along the perimeter, feeling the resistance of the glue and gradually cutting through it. Take your time, moving in jerks, act smoothly and progressively.
☑️ Removal of the back cover
When the lid is removed, you'll have access to the inside, but you can't get inside right away. The first thing you need to do is turn off the battery plume to shut off the board and avoid short circuits when you disassemble it, and that's a key safety rule for any electronics repair.
Carefully bend the protective plastic bar covering the connectors, and with a plastic shoulder blade or finger, click the battery connector, only then you can safely disconnect other plumes, including the display module and touch screen.
Dismantling of protective screens and main board
Once the device is de-energized, you can start removing the metal screens that protect the motherboard. In the Redmi 9A, they can be glued or secured with screws that also require careful handling.
| Component | Type of attachment | Tool. | Risk of damage |
|---|---|---|---|
| Fee screens | Glue/Spins | Scapula/P2 | High (may damage small elements) |
| Basic fee | Screws + plumes | P0/P2 | Medium (risk of plume breakage) |
| Battery | Adhesive tape | Scapula/Thread | High (battery puncture) |
| Display module | Frame + glue | Fen/Spaddle | Critical (matrix battle) |
When you unscrew all the visible screws holding the board, don't pull it upwards. Check if all the plumes are off. Often, under the main connectors, there may be additional antenna connections or buttons that are easily overlooked in poor light.
Raise the board carefully, controlling every millimeter of its movement. If you feel resistance, stop and double-check the connections. The motherboard is the most expensive component of the phone, and damaging it is often economically impractical to repair.
💡
When unscrewing the main board screws, sort them by length. Redmi 9A uses screws of different lengths, and installing a long screw in a short hole can punch through the paths on the board, leading to complex and expensive repairs.
Battery extraction and glue handling
Replacing the battery in the Xiaomi Redmi 9A is one of the most common causes of disassembly. The battery in this model is glued to a plastic frame quite firmly, and its removal requires patience and compliance with safety precautions.
Never try to imitate (the battery) with metal objects or exert excessive force.Puncture of a lithium-polymer battery causes instant fire and release of toxic substances.Use a plastic card or a special thread for careful separation.
⚠️ Attention: If the battery is swelling, be very careful. Any pressure can disturb the integrity of the shell. In such cases, it is better to first carefully cut the package (without touching the insides) and inject a little alcohol to dissolve the glue before removing the element.
To make the process easier, you can slightly warm the back of the phone (already without a cover) with a hairdryer to soften the adhesive layer under the battery. However, warm carefully so as not to damage the display on the other side if it is still installed in the frame.
Once the old battery is removed, clear the seat of glue residues. The surface must be perfectly smooth and clean so that the new battery will lie flat and hold secure. Use a lilaless napkin moistened with alcohol.
Removal of the display module and frame
If your goal is to replace a broken glass or matrix, you will need to remove the display module from the plastic bezels.In the Redmi 9A, the screen is glued around the perimeter, and its dismantling is the most risky part of the repair.
The process is similar to removing the back cover, but requires even more delicacy: heat the front of the phone, passing the blade between the frame and the module. Try not to bend the display itself, as IPS or LCD matrixes are very sensitive to mechanical deformations.
In some cases, it's easier and cheaper to buy a display module that's already pasted onto a new frame, so you don't have to mess around with the glue and risk the integrity of the fragile glass when you reglaze. But if you only change the glass, you have to be prepared for a long and painstaking job.
Notice the lights and touchscreen plumes, they're very thin and they break easily. When you disconnect, use a magnifying glass to see the connector locks. The protective film on the new modules is only removed after you've fully installed and checked.
Assembly of the device and verification of functionality
The phone is assembled in reverse disassembly. Set up a new battery or refurbished module, plug in the battery plume first thing. Then gently stack the fee, making sure all the connectors fall into place with a characteristic click.
Twisting all the screws, but don't pull them over. The plastic that makes up the Redmi 9A can crack under pressure, make sure that the screws don't get plumes, otherwise they'll be broken when they're tightened.
Before you finally seal the back cover, do a pre-check. Turn on the phone, check the sensor, sound, vibration and cameras. Make sure the phone sees. SIM-map and Wi-Fi network.
💡
Final inspection of all functions before full encapsulation of the housing will save you time to re-disassemble in case of a defect or error during assembly.
If everything is working correctly, apply a new layer of glue (B-7000 or analog) to the end of the case and tightly press the back cover. Lock it with rubber bands for 15-20 minutes before the initial grasp of the glue.