How to Clean Xiaomi Vacuum Cleaner: The Complete Guide

Xiaomi’s robotic and wireless vacuum cleaners have proven to be reliable cleaners, but even the most advanced technology requires regular maintenance. Ignoring the need to clean the main nodes leads to a drop in suction power, extraneous noises and eventually a breakdown of an expensive engine. Owners often wonder how to properly maintain the device to extend its life without going to a service center.

Timely removal of dust, hair and debris from filter elements and brushes is not just a matter of hygiene, but a critical procedure to maintain the declared performance. Modern models such as the Xiaomi Vacuum Mop 2 Pro or Roborock S7 are equipped with a complex system of sensors that can become contaminated faster than you think. In this article, we will detail the process of cleaning all components to make your gadget work like new.

Before we start disassembling, it's important to understand that different models may have design features, but the basic principles of care are identical. We'll look at universal steps that are suitable for most Mijia ecosystem devices. The right approach will avoid the common mistakes that inexperienced users often make in the first service.

Preparation for cleaning and safety measures

The beginning of any technical procedure should be accompanied by compliance with safety rules. The first step is always to completely disconnect the device from the charging station. If you are maintaining a robot vacuum cleaner, make sure that it is not in the process of cleaning or charging. For wireless models like Xiaomi Handheld Vacuum, you need to remove the battery if the design allows it, or just make sure that the device is turned off.

⚠️ Warning: Never attempt to disassemble the main engine unit or open the sealed compartments with the battery, as this will lead to loss of warranty and can be dangerous.

You'll need to prepare a workspace with good lighting and free access to the sink, stock up in advance with a dry soft cloth, a soft brush (you can use a clean paintbrush), and, if necessary, tweezers for hair removal. HEPA-filters and plastic containers that allow contact with water, but electronic modules must remain completely dry.

It is recommended to clean in a well-ventilated room, especially if you have not looked inside the dust collector for a long time. Dust suspension may contain allergens, so using a protective mask will be a smart step for people prone to allergic reactions. Also prepare a garbage container to immediately dispose of the contents of the container.

💡

Use an old dryer in cold air mode to dry plastic parts quickly after washing, but don't direct the hot jet to rubber seals.

Cleaning of the main dust collector and cyclone filter

The centerpiece of any Xiaomi vacuum cleaner is a dust collection container. Depending on the model, it can be integrated into the case or made as a removable module. First, you need to remove the container, following the instructions for your particular model, usually by pressing the lock button, inside you will see the bulk of the debris that you need to remove.

Shake the contents in the bin to minimize contact with dust. Inside the container is often a cyclone filter or net that protects the engine from large fraction of debris. This element must be thoroughly washed under running water. Use a soft brush to remove contaminants from the mesh cells, but avoid using aggressive detergents that can damage the plastic.

After washing the plastic parts, they need to be thoroughly dried. A wet container installed back in the vacuum cleaner can cause mold and unpleasant odor, as well as damage to the motor. Make sure all parts are completely dry before you assemble the device. It usually takes 12 to 24 hours to dry completely depending on the humidity of the air.

Service HEPA-filtering and filtration systems

The system of fine air cleaning in vacuum cleaners Xiaomi is based on HEPA-These filters are usually located just behind the dust container or in a separate compartment on the back of the device, and their condition directly affects the quality of the air blown out and the suction capacity.

Most of the modern HEPA-The filters in Xiaomi devices are cleanable, but they must be handled very delicately. Wash the filter under a weak stream of water without using brushes, so as not to damage the fine structure of the fibers. You can not wipe or squeeze the filter categorically — it will destroy its structure. Let it dry naturally for at least 24 hours.

⚠️ Attention: Installation of wet HEPA-The filter will cause electronics to short circuit or bacteria to develop, so make sure it is completely dry to the touch.

Term of service HEPA-The filter is limited, even with regular cleaning, and over time, the pores become clogged with the smallest dust that can not be washed, and if after cleaning, you notice that the vacuum cleaner has become quieter or warmer, it is time to replace the filter with a new original or certified counterpart. Regular replacement is the key to a long engine life.

Care for the main brush and side blizzards

The main turbobrush is the mechanism most commonly affected by the hair, thread and fur of animals, which requires the vacuum cleaner to be turned over or the bottom cover removed (depending on the model), and comes with most Xiaomi models with a special knife tool designed specifically to cut the wound hair.

Carefully cut the tangled hair tangles along the brush axis and remove them. Don't pull the hair with force so as not to damage the bearings or the bristles themselves. After removing the debris, wipe the brush with a wet cloth. Side brooms also require attention: remove them, remove the stuck debris and wipe them. If the bristles are badly worn or deformed, it's better to replace it.

It's important to check the shaft on which the brush is wearing. Hair often accumulates on the ends of the shaft, which blocks rotation. Remove it with tweezers. A clean, obstructive brush ensures that carpet dust is effectively dislodged, which is a key function of robot vacuum cleaners.

💡

Regular cleaning of the main brush from the hair prevents engine overload and break of the drive belt.

Cleaning sensors and wheelbase

Xiaomi relies on an array of sensors located on the bottom and front of the device. Fall sensors (cliff sensors), collision sensors and lidar (if any) should be clean to build a map correctly and prevent falls from stairs.

The wheels of the device also need care. The wheels often have hair around the axis, which over time can block the mechanism or damage the motor wheel. Use tweezers or a knife from the kit to carefully remove dirt. Check the free running of the wheels - they should be easy to scroll and spring.

Charging contacts on the bottom of the vacuum cleaner and at the docking station are periodically oxidized or covered with dust, which leads to charging problems.

Table of component maintenance frequency

For the convenience of users, we have created a summary table that will help to systematize the process of care of the device, observing these intervals will avoid sudden breakdowns and maintain the efficiency of cleaning at a high level throughout the life of the device.

Typical errors in service

One of the most common mistakes is using hot water to wash filters.Hot water can warp the fine structure HEPA-Always use room temperature water, and users often forget to dry the filters for a sufficient amount of time by running a wet device, which is fatal for electronics.

Another mistake is to use a vacuum cleaner to clean building dust, gypsum or fine cement dust without first consulting the instructions, which can instantly clog the filter pores and damage the motor, because they are too small for cyclone filtration and too abrasive for the engine.

⚠️ Warning: Do not use Xiaomi vacuum cleaner to collect liquids unless it is a specialized washing model.

Ignoring the indicators on the Mijia or Xiaomi Home app is also a mistake. The app often tells you to clean the main module or change the filter. If you see a notification, it is better to take maintenance time immediately than then disassemble the entire device.

Frequently Asked Questions (FAQ)