Modern smartphones like the Xiaomi Redmi 9C are equipped with large displays that are extremely vulnerable to mechanical damage. Even a microscopic grain of sand in your pocket can leave an irremovable mark on an oleophobic coating or split the matrix when you fall, which is why the protective glass becomes the first and most important accessory you need to purchase immediately after you buy a device.
The process of sticking often causes fear among gadget owners because of the risk of air bubbles or dust. However, if you approach the matter methodically and prepare the workplace, anyone without special skills can cope with the task. In this article, we will discuss in detail how to perfectly paste protection on the screen of your smartphone, avoiding the typical mistakes of beginners.
A well-designed procedure will not only preserve the aesthetic appearance of the gadget, but also significantly extend its life. The Redmi 9C screen has certain design features that must be considered when choosing and installing an accessory. Let's look at all the stages of preparation and the process itself, so that you will enjoy the result.
Choosing the right protective glass for the Redmi 9C
The first step is to buy the right accessory.The market is full of offers, but for the Xiaomi Redmi 9C it is critical to find a model with the right form factor.The screen of this smartphone has a drop-shaped cutout for the front camera, and the glass must exactly repeat this geometry without overlapping the lens.
Pay attention to the hardness of the material, which is usually labeled as 9H. It's not just marketing, but a measure of resistance to scratching keys and trifles. Cheap films quickly lose transparency and stop protecting the display from impacts, turning into a useless layer.
⚠️ Please note: Do not buy glass designed for Redmi 9 or 9A. Despite the similarity, the Redmi 9C different location of the dynamic conversational speaker and the size of the cutouts, which will lead to incorrect operation of the proximity sensors.
Also worth considering is a full-glue option, which is adjoined across the entire area, including the curved edges, providing better protection and no perimeter rainbow effect, and regular silicone-based glass can peel off at the edges over time, collecting dirt.
Tools and workplace preparation required
The success of the surgery is 90% pre-prepared. You don't need complex equipment, but cleanliness is crucial. It's best to do the procedure in the bathroom after the steam has passed, precipitating all the flying dust, or in the kitchen, having previously wiped the table with a damp cloth.
Most high-quality glass already includes a set of mountables, usually wet and dry wipes, and a sticky dust removal sticker, and if something is missing, you can use home counterparts, but with caution.
Here is a list of what you should have on hand before starting your work:
- 🧼 Wet alcohol wipe for degreasing the surface.
- 🧻 Dry lilaless fabric (microfibra) for polishing.
- 🏷️ Sticky Scotch or Special Sticker for Final Cleaning.
- 💡 A bright light source (table lamp) to see dust particles.
It's important to ensure good lighting. The shadow from your head or hands shouldn't fall on your smartphone screen while you're running. The Redmi 9C display has a glossy coating that shows the smallest contamination, so the light should fall at an angle to reveal defects.
💡
Turn on the room humidifier or just spray water from the spray 15 minutes before work - this will nail the dust to the floor and will not allow it to settle on the adhesive layer.
Stages of preparing the smartphone screen
Before you pick up a new glass, you need to perfectly prepare the screen of your smartphone, even if it seems clean visually, it always has fat fingerprints and microscopic dust particles on it. Start by thoroughly wiping the display with a wet wipe.
The movements must be confident, but not too strong, so as not to damage the matrix under strong pressure. Walk across the surface, paying special attention to the edges and area around the front camera. After that, dry the screen with a dry wipe from the microfiber.
The final and most important step is to remove the static dust. Use the sticky side of the sticker (or the regular tape rolled into the ring with the sticky side outwards), walk the tampon-dub movement all over the screen, lifting the smallest villi that the fabric has not removed.
☑️ Screen preparation checklist
If you notice that after cleaning the screen again sat a speck of dust, do not try to blow it away with your mouth. Exhaled air contains microparticles of moisture that will settle on the sticky layer of glass and create an indissoluble stain, preferably use a special pear or just gently shake off the air with your hand next to the screen.
Technology of the sticker: step-by-step instructions
The most critical moment is now: Take the safety glass by the ends, trying not to touch the adhesive surface with your fingers, hold it to the smartphone screen without removing the protective film from the glass itself, and try it on the cutouts, make sure that it does not overlap the speaker and the camera.
Carefully remove the bottom protective film (usually marked with a number 1 or "Back"). Don't touch the adhesive layer with your fingers! Match the glass with the screen, focusing on the edges of the case and cutouts. When the ideal position is found, gently lower the glass to the center of the screen.
The glass must stick itself under gravity and adhesion. If it's crooked, don't panic -- until the adhesive layer is pressed hard, you can gently lift the glass around the corner and fix it, but do this only once so that you don't damage the silicone layer.
⚠️ Warning: If you pressed the glass hard and saw a skew, don't try to rip it off sharply.Put the edge with a thin plastic map and slowly lift it, otherwise the glass may burst or stretch.
Once the glass has fallen into place, smooth it from center to edge, expelling air. Use a dry napkin or a plastic card wrapped in cloth. Movements should be smooth, without much pressure. Usually the whole process takes no more than a minute.
What do I do if there is air left?
Removing defects: dust and bubbles
Even in the hands of experienced craftsmen, dust sometimes gets under the glass, which is not a reason to change the accessory, if you know how to eliminate defects. Small air bubbles often disappear on their own within 24-48 hours, as the adhesive layer is distributed evenly.
If a villi or a grain of sand is trapped under the glass, remove it, and then carefully tuck the edge of the glass over the problem area with a thin needle or tape, insert the edge of a sticky sticker into the gap and mark the dust.
There is a table of problems and methods of their solution:
| Type of defect | Cause of the occurrence | Elimination method |
|---|---|---|
| Small bubbles | Residual air | Smoothing from the center, waiting 24 hours |
| Big bubble. | Dust trapped | Raise the edge, remove the dust with scotch |
| Rainbow spots | Bad fit. | Stronger to press the edges, warm up with a hair dryer (carefully). |
| Fat spot. | Touching glue with your finger | Wash the edge of the glass with alcohol before the sticker |
Sometimes the villi stick to the most adhesive layer of glass and interfere with the view, in which case you can use the "flipper" method. Remove the glass completely, put it with the adhesive side up on a clean surface (for example, on a glass box), remove the dust and paste it again.
💡
The main rule of dust control is to act quickly and use a sticky sticker, rather than blowing on a screen or glass.
Polymerization of glue and final tips
After a successful sticker, the process is not over, and the adhesive layer takes time to fully polymerize and bond to the oleophobic coating of the screen, and in the first hours, it is better not to use the smartphone actively and not put it in your pocket.
It is recommended to leave the device alone for 1-2 hours at room temperature. If the room is cold, the process may take longer.Some users gently warm the edges with a hairdryer at a minimum temperature, but for the Redmi 9C this is rarely required if the glass is of good quality.
In the first day, try to avoid moisture on the joints of the glass and the case. Also, do not wear a case if its edges are strongly pressing on the ends of the protective glass - this can lead to its detachment in a few days.
Rub the screen regularly with a soft cloth, and despite the presence of an oleophobic coating on the glass, aggressive chemistry can destroy it, using only special sprays for screens or a slightly damp microfiber.