How to put a protective glass on Xiaomi Redmi 9A

Screen protection for budget smartphones is not just an accessory, but a necessity, especially when it comes to the popular Xiaomi Redmi 9A. The screen of this device is made of glass, which, despite modern hardening technologies, remains vulnerable to falls, bumps and scratches from keys in your pocket. Replacing a broken display can cost 60-70% of the cost of the device itself, while a quality protective glass costs a penny and is able to take the entire blow.

Many users are afraid to take this procedure on their own, for fear of bubbles, dust under a layer of glue or skewed. However, if you know the right sequence of actions and prepare the workplace, the process takes no more than 10-15 minutes. In this article, we will discuss in detail how to paste the protective glass on the Redmi 9A so that the result looks like a factory.

The success of the surgery is 90 percent pre-prepared. You don't need sophisticated tools or professional skills, but clean hands and the environment are critical. We'll look at everything from consumable selection to finish polishing, eliminating the typical novice mistakes.

Selection of protective glass and preparation of the workplace

Before you start gluing, you need to make sure the quality of the accessory itself.The market is oversaturated with cheap copies that quickly scratch, have poor oleophobic coating (fat-repellent coating) and may not fit correctly to the edges of the curved screen Xiaomi.The optimal choice will be tempered glass with a hardness of 9H and a thickness of 0.26-0.33 mm, which provides a balance between protection and sensitivity of the touchscreen.

Pay special attention to the type of edge covering. For the Redmi 9A, it is better to choose glass with a black frame that completely covers the active matrix, but does not go to the curves of the body. If the frame is too wide, the glass can peel off at the edges or conflict with the covers. It is also important to check the presence of all the necessary components in the kit: wet and dry wipes, as well as a sticky tape to remove dust.

⚠️ Warning: Don't use cheap polyethylene films as permanent protection. They don't extinguish bumps when falling and quickly lose transparency, turning into a cloudy spot on the screen.

Preparing the workplace is the second critical step: Choose a well-lit table, preferably by the window in daylight, to see the smallest villi. The ideal place is a bathroom where, after turning on hot water, the dust settles faster and the humidity prevents static, although in a dry room with minimal air movement, the result will be predictable.

• 🧼 Wash your hands thoroughly with soap to degrease your fingers and avoid leaving traces on the adhesive layer.
• 💡 Provide bright side lighting that will help you spot dust on the screen at an angle.
• 🧹 Rub the surface of the table with a wet cloth to remove settled dust before work begins.

Besides the glass itself, you may need an additional tool if you plan to be as careful as possible. Some craftsmen use special dust remover stickers or even the usual wide scotch wound sticky to the outside for the final cleaning, and it is also useful to prepare a soft lilaless fabric if the complete napkin seems too rough.

Cleaning the display: a key stage of success

The most common reason for a bad glue is a screen that is not well cleaned, and even a microscopic villi that is invisible to the eye will turn into a noticeable air pocket when the glass is pressed. Start by turning on your smartphone screen to better see the contamination, and gently wipe the surface with a wet wipe from the kit.

The movements must be confident, but without strong pressure. Pay special attention to the corners and areas around the speaker where skin fat and dust often accumulate. If the screen was heavily contaminated, the procedure with a wet wipe can be repeated twice, waiting for the moisture to dry completely.

After wet cleaning, you have a dry polishing phase. Use the second napkin from the kit to remove the stains and moisture residues. Touchscreen should be perfectly smooth and creaky to the touch. Don't touch the screen with your fingers after this phase, as the skin fat will immediately disrupt adhesion of the glue.

The final touch before you remove the protective film from the glass is to use a sticky tape, and you can walk it all over the display surface, slapping it a little bit, to collect the dust that has settled during the preparation, and this simple technique saves you from 95 percent of potential bubbles.

If you drop a glass layer on the floor or touch it with your finger, don't panic. Blow the dust carefully or press the contamination with sticky tape on the back, trying not to stretch the glue layer. The glue layer on the quality glass is self-healing and can "tighten" small contaminants if removed quickly.

Application technology: from centering to pressing

The most critical moment comes: remove the bottom protective film from the adhesive layer, trying not to touch the adhesive surface with your fingers. Many of the glass models for Xiaomi Redmi 9A have a special guide frame or tags for alignment, which makes it much easier to do.

Put the glass above the screen, orient yourself to the speaker cutouts and the front camera. Smoothly lower the glass onto the display. With the high-quality silicone glue, the glass will itself magnetize to the screen and begin to spread from center to edge. Don't push hard into the center at once, let the air come out on its own.

⚠️ Note: If the glass is curved, it can be carefully lifted and corrected only in the first 10-15 Do not try to move the glass if it has already "sit" over the entire area.

Once the glass has fallen into place, start smoothing from center to edge. Use a dry wipe or a special plastic spatula (if included). The movements should be sweeping, as if you are driving air from under the surface. Pay special attention to the edges where the glue dries the longest.

It may take a little effort to get the edges right. Walk your finger around the perimeter, paying attention to the areas. 2.5D-If you hear the characteristic "stick" sound, it's going right. In some cases, it's helpful to warm the edges slightly with a hair dryer at a minimum temperature to activate the glue, but for Redmi. 9A It's rarely required.

Eliminating bubbles and dust under glass

Even skilled craftsmen sometimes have small defects. If you notice an air bubble, try to push it to the nearest edge by pressing and moving your finger. Large bubbles often turn out to be just zones where the glue has not yet spread, and they disappear by themselves through the passage of a finger. 24-48 hours.

The speck of dust under the glass requires a more delicate approach: you'll need a thin needle or pin, and a sticky tape. Carefully lift the edge of the glass above the speck of dust, insert the needle under the glass, put the mote on, and, without removing the needle, press the dust with sticky tape, pulling it out.

• 📌 Use a thin needle to minimize gap when glass is lifted.
• 🌬️ Blow on the screen before lowering to blow off static dust.
• 🧲 Use an antistatic brush if you have one in your arsenal.

If the bubble is left and you can't kick it out, you can try to push it slightly through the fabric for 30-60 seconds, sometimes a slight tapping of the finger on the center of the bubble helps, the main thing is not to overdo it, so as not to damage the matrix of the display under pressure.

Comparison of types of protective coatings

Choosing between different types of protection can be tricky. To understand why we recommend tempered glass for the Xiaomi Redmi 9A, let’s compare the main options in the table. This will help you assess the feasibility of buying a particular accessory in the future.

As you can see from the table, tempered glass is the middle ground, providing the maximum transparency and tactile response comparable to the original screen, while taking on the impact energy of the fall. Hydrogel films are good for curved flagship screens, but on a flat Redmi 9A, the glass looks and feels better.

Liquid glass is more of a marketing tool for microscratching, but it won't save you from a phone falling face down, so for everyday use of a budget smartphone, the choice is obvious in favor of a classic tread.

Care and maintenance after gluing

After a successful installation of the protective glass, you should not immediately expose the smartphone to extreme loads. Let the glue finally polymerize within 1-2 hours. At this time, it is better not to put the phone in your pocket with the keys and not to put a tight case that can put pressure on the edges.

Rub the glass surface with a soft cloth regularly. Despite the presence of oleophobic coating, greasy fingerprints can accumulate, reducing sensitivity and impairing visual perception. Use of alcohol wipes for screens is permissible, but not more than once a week, so as not to overdry the coating.

⚠️ Warning: Avoid using aggressive chemicals, acetone or abrasive sponges to clean glass.This will destroy the oleophobic layer and the screen will become rough and sticky.

If you wear a phone in a case, make sure it is compatible with the glass you choose. Some cases have high sides that can lift the edges of the glass when you put it on, which will cause "rainbow" detachments around the perimeter, in which case the glass is better replaced with a smaller model or cut a compatible case.

💡

Tip: Check the edges of the glass once a month, and if you notice that it has begun to move away, gently press or replace the accessory so that dust does not fall under it and scratch the main screen.

Frequently Asked Questions (FAQ)

💡

High-quality glued glass on Redmi 9A extends the life of the display 3-4 times and retains the liquidity of the smartphone during resale.