How to wash the vacuum cleaner Xiaomi Dreame: the complete instructions for the care of the robot vacuum cleaner

Xiaomi Dreame vacuum cleaners have become indispensable cleaning aids, but their effectiveness depends on proper care. Many users make critical errors when washing, leading to engine failures, contact corrosion or reduced suction power. This article will examine the phased cleaning of all components from the main body to side brushes, taking into account the features of the Dreame D9, D10, Bot W10 and others.

We analyzed the manufacturer’s official recommendations, service center reviews and owners’ experience to come up with a safe method that will prolong the life of the appliance, with a special focus on hidden areas of dirt accumulation that are not covered in standard instructions, but which lead to 70% of malfunctions after a self-driving wash.

Preparation for washing: what to do before disassembly

Before you start cleaning, disconnect the vacuum cleaner from the mains and remove the battery (if the model allows), which will prevent short circuits when moisture hits the contacts. The Dreame Bot L10 and W10 models have a built-in battery, in which case it is enough to remove the dust collector and filters.

Prepare your workspace by putting a towel or rubber mat to avoid scratching the body.

• 🧼 Soft sponge or microfibre wipe
• 🧴 A means for washing dishes (without abrasives)
• 🪥 Soft bristles toothbrush
• 🔧 Plastic spatula (to remove adhering dirt)
• 💧 Distilled water (for filter rinsing)

Pay attention to the pollution level: if the vacuum cleaner was removing building dust or animal wool, it would require a deep cleaning with disassembly. For normal cleaning, surface treatment is enough. Don't use hot water, it deforms plastic parts and destroys seals.

Disassembly of the vacuum cleaner: what parts can be washed and which ones can not

Not all components of the Xiaomi Dreame allow contact with water, and the table below shows the details that can and cannot be wet:

For disassembly, follow the instructions:

1. Press the latch of the dust collector and remove it.
2. Unscrew the screws (if any) on the bottom cover to access the brush.
3. Remove the side brushes by pulling them up.
4. Extract. HEPA-back-filter.

Step-by-step washing of dust collectors and filters

The dust collector is the most polluted element.

1. Remove the large debris manually.
2. Soak the container in warm water (not higher than 40 ° C) with the addition of dishes for 15-20 minutes.
3. Use a toothbrush to clean corners and seal gum.
4. Rinse thoroughly under running water and leave to dry for 24 hours in a ventilated place.

HEPA-The filter requires a special approach:

• 🚫 Don’t rub it with a sponge – it will damage the microfibers.
• 💨 Blow the filter with compressed air (for example, a dryer in cold mode).
• 🚿 If a wash is needed, use only distilled water without detergents.
• ☀️ Dry the filter for at least 48 hours – the wet filter becomes a breeding ground for bacteria.

Make sure all the details are dry|Check the integrity of seals|Clean the contacts of the dust collector from dust|Install the filter on the correct side-->

⚠️ Warning: Never dry parts with a hair dryer in hot mode or on a battery. HEPA-The filter can lose up to 30% of its filtering capacity.

Cleaning brushes and rollers: remove wound hair and wool

The side brushes and the main roller are clogged with hair and thread, which reduces the efficiency of cleaning by 40-50%.

1. Remove the brushes from the axle by pressing the locks.
2. Remove the wound hair with a knife or a special cleaning tool (comes complete with some models).
3. Wash the brushes under running water, paying attention to the base where the dirt accumulates.
4. For the main roller, use a plastic spatula to scrape the stuck dirt between the bristles.

After washing, check the brush bearings: if they make creaks or backlashes, grease them with silicone grease (1-2 drops). Don't use oils based on petroleum products - they corrode plastic.

💡

To remove persistent contaminants (such as dried dirt on a roller), use a 3:1 mixture of water and vinegar. Soak the part for 10 minutes, then rinse with clean water.

Cleaning sensors and sensors: why the vacuum cleaner “blind” after washing

Obstacle sensors, laser sensors (in models with LDS-Scanners and infrared ports require careful care, and pollution causes the vacuum cleaner to be cleaned:

• 🤖 Ducks with furniture
• 🌀 He's chaoticly moving around the room.
• 🚫 Can't see stairs or rapids

For cleaning:

1. Wipe the sensors with a dry microfibre wipe (wet fabric leaves wiring).
2. For a laser sensor (Dreame Bot Z10 Pro), use a cotton swab dipped in alcohol.
3. Blow the infrared ports with compressed air (without touching the membrane).

⚠️ Warning: Do not use alcohol to clean plastic sensor lenses - it clouds the optics. Only distilled water or special wipes for optics are suitable for glasses.

Drying and Assembly: How to Avoid Corrosion and Mold

Improper drying is the main cause of breakage after washing.

• ☀️ Dry parts at room temperature (not on a battery or in direct sunlight).
• ⏳ Minimum drying time: 24 hours for plastic, 48 hours for filters.
• 💨 Use a fan to speed up the process, but don’t direct airflow directly to parts.

When assembly, pay attention to:

• 🔌 The density of the adjoining contacts of the dust collector - oxidation leads to an error "Check the dust collector".
• 🔄 Proper installation HEPA-filter (the arrow on the filter should point towards the airflow).
• 🔧 Swirling all screws - the backlash of the body causes vibration and noise when working.

💡

Even a drop of moisture in a dust collector can short the next time you turn on. Always check the dryness of parts with a multimeter (resistance between contacts should tend to infinity).

Frequent Mistakes and How to Avoid Them

Analysis of the service centers showed that 85% of the breakdowns after washing are associated with five errors:

1. The use of aggressive detergents (for example, "Domestos" or abrasive powders) - they corrode seals and body paint.
2. Drying with a hair dryer - leads to deformation of the plastic and cracks in the dust collector.
3. Skipping cleaning sensors - the vacuum cleaner begins to "glutch" after 1-2 cleanings.
4. Incomplete disassembly – dirt under the main brush accumulates and blocks rotation.
5. Ignoring filters - clogged HEPA-filter reduces the suction power by 60%.

If after washing the vacuum cleaner:

• 🔊 It's louder than usual. → Check if the water has been in the brush bearings.
• 🚫 Not included. → Check the contacts of the dust collector for oxidation.
• 🌪️ It sucks badly. → Wash the filters or replace them.

FAQ: Answers to popular questions