How to Wash a Xiaomi Dreame Vacuum Cleaner V10 No risk of breakdown: a complete guide with photos and tips

Robot vacuum cleaner Xiaomi Dreame V10 It's a real cleaning tool for thousands of users, but it depends on proper care, and many owners are faced with the problem of how to wash a device so that you don't damage the electronic components, but still keep it in perfect condition. This article debunks the myths about "unwashed" vacuum cleaners and will give a step-by-step instruction taking into account the features of this model.

Unlike the classic vacuum cleaners, Dreame V10 It's a delicate approach, and you can't just rinse it under the tap, and it's important to understand what parts you can wash and what you can wipe, how to dry the components properly, and how often you can do deep cleaning, and we'll sort through all the critical nuances. from preparing for washing to handling sensors and sensors that often fail due to improper care.

We pay special attention to hidden "traps" in the design V10, For example, why can't you use alcohol to clean the contacts of the charging station or how to properly wash the turbobrush so that it doesn't halve its life. If you want your vacuum cleaner to last more than 5 years without repair, this article is for you.

Preparing for the wash: what can and can not be done with Dreame V10

Before you start water procedures, you need to disconnect the vacuum cleaner from the network and remove the battery (if you can do this without the risk of damaging the contacts). V10 degree of protection IP54, But it's only dust and splash -- it's strictly forbidden to dive completely into water.

Here’s what to do before the sink:

• 🔋 Remove the vacuum cleaner from the charging station and turn it off with the power button (hold 3 seconds).
• 🗑️ Cleaning the garbage container from large litter manually - this will prevent clogging of filters during washing.
• 🛠️ Prepare tools: soft brush (for example, toothbrush), microfiber cloth, cotton swabs and only warm water (not higher than 40).°C).
• 🚫 Remove detergents with abrasives or harsh chemicals (for example, "Domestos" or "Comet").

One of the most common questions is, can you wash a vacuum cleaner in the shower? The answer is no, even if you see it on YouTube. A jet of water under pressure can penetrate the microcracks of the case and cause circuit boards to corrosion. The best way to do that is to use a basin of water and a soft sponge.

⚠️ Warning: Never point the water jet at infrared sensors (black round elements on the body) and charging contacts (metal plates on the bottom) and can only be wiped with a dry wipe soaked in isopropyl alcohol (no more than 70% of the concentration).

Disassembly of the vacuum cleaner: what details can be removed for washing

Xiaomi Dreame V10 It's a structurally-constructed, removable module, but not all of them are designed to come into contact with water:

To remove the garbage container, press the locker button on the side (marked by the arrow) and pull it upwards. The turbobrush is attached to two latches, which must be carefully squeezed with a screwdriver or a nail. Do not use force: if the part does not respond, check if there are any undetected locks.

Pay special attention to the sidebrush. V10 It has a plastic shaft that accumulates hair and thread over time, and if you don't clean it regularly, the brush will slip and it will get worse at collecting garbage along the walls.

Disconnect the vacuum cleaner from charging|Removing the garbage container|Remove the turbobrush and side brush|Prepare warm water and a soft brush|Check the integrity of the sealing rubbers-->

Step-by-step: how to wash removable parts

Now, to the sink itself, let's start with the garbage container, which is the most polluted part of the vacuum cleaner.

1. Soak the container in warm water with liquid soap on 10-15 It'll help to oxidize the adhesive dust and fat.
2. Use a soft brush (for example, for baby bottles) to clean the corners and ribbed surface inside. Do not use metal sponges!
3. Wash thoroughly under running water, making sure there is no debris left in the drainage holes (small holes below).
4. Dry the container naturally during the 12-24 Do not use a hair dryer or battery - this can warp the plastic.

For a turbobrush, the process is a little more complicated:

• 🧹 Remove the brush from the vacuum cleaner by pressing two latches on the sides.
• 🔗 Remove the wound hair and threads from the shaft. V10 There is a special cleaning knife (included in the package).
• 💦 Wash the brush under running water, avoiding moisture on bearings (they are closed with rubber plugs).
• 🔄 Scroll the brush with your hand after washing - if it rotates with difficulty, then the bearings need to be lubricated with silicone lubrication (1 drop on each side).

You just need to wash the sidebrush in soapy water and wipe the mounting groove with a cotton swab. Notice the rubber seal on the axis of the brush, if it cracks, the brush will luft and press harder against the floor. In this case, the part needs to be replaced (Dreame article). V10: DM-V10-SIDE-BRUSH).

💡

If the turbobrush starts to make more noise than usual after washing, check if water has entered the bearings, in which case dry the brush for an additional 24 hours in an upright position (shaft down).

Cleaning filters: why HEPA-filter cannot be washed

One of the most common myths is that HEPA-You can wash the filter with water. It's strictly forbidden! V10 class filter HEPA H11, It's made up of microfibers, and it comes in contact with water:

• 💧 The fibers are glued together, reducing the filter capacity.
• 🦠 On the wet surface, bacteria and mold actively multiply.
• 🔥 Risk of short circuit when moisture hits contacts.

So how do you clean the filter? Here's the right algorithm.

1. Remove the filter from the vacuum cleaner (it is under the lid of the garbage container).
2. Carefully tap the filter on a solid surface to shake off large dust particles.
3. Use a vacuum cleaner in blow mode (or a cold air dryer) to blow the filter on the back.
4. For deep cleaning, use a special cleaner for HEPA-filters (e.g. Karcher) FC Apply it with spraying, then shake off the surplus.

Term of service HEPA-filter in Dreame V10 — It's about 6 months with heavy use, and if you notice that the vacuum cleaner is getting worse or has a bad smell, it's a sure sign that it's time to replace the filter: DM-V10-HEPA.

⚠️ Warning: After cleaning the filter, always check the sealing rubber at the edge. If it loses elasticity or breaks, the filter will not fit tightly and dust will begin to enter back into the room.

Caring for the case and sensors: what can and can not be used

The Xiaomi Dreame case V10 It's made of glossy plastic that scratches easily. Never use it to clean it:

• 🧴 Means with abrasives (for example, pastes) GOI Autosol).
• 🧽 Hard sponges or metal scrapers.
• 🔥 Solvents (acetone, white spirits) – they corrode plastic.

The best option is a microfibre wipe dipped in a weak soap solution (1 drop of dishes per glass of water). To remove greasy spots or traces from the fingers, you can use isopropyl alcohol 70%, but only on unpainted surfaces (not on the logo or decorative inserts).

Special attention is required to sensors and sensors:

• 👁️ Laser rangefinder (upper rotating tower) - wipe only with a dry wipe without pressing.
• 📱 Infrared sensors (black round elements) - clean with a cotton swab dipped in alcohol.
• 🔋 Charging contacts - wipe with a dry wipe, use an eraser when oxidizing.

If the vacuum cleaner starts to "glut" - for example, does not see obstacles or does not dock well with the base, in 90% of cases the problem is in contaminated sensors. Xiaomi official service recommends cleaning the sensors at least 1 time a month, even if the vacuum cleaner looks clean.

Drying and Assembly: How to Avoid Corrosion and Mold

The most critical part of the process is drying, and even drops of water left in secluded areas can cause corrosion or short circuiting.

• ⏳ Minimum drying time for removable parts - 12 hours at room temperature.
• 🌬️ Use a fan to speed up the process, but do not direct airflow directly to the plastic (may cause deformation).
• 🚫 Don't build a vacuum cleaner if there's condensation on the parts, and you can test this by breathing on the surface -- if there's a drop, the drying isn't complete.

Pay special attention to the turbobrush.

1. Remove the plugs from the bearings (carefully smacking the screwdriver).
2. Wet the shaft with a paper towel.
3. Apply 1 drop of silicone lubricant to each bearing.
4. Scroll the brush. 10-15 Once the lubricant is evenly distributed.

When assembling a vacuum cleaner, make sure that:

• 🔄 All the removable parts came into place with a slight click.
• 🔌 Charging contacts on the body and base matched (they should be clean and shiny).
• 📦 The lid of the garbage container was tightly closed - if there is a gap, check the seal.

⚠️ Warning: If the vacuum cleaner makes an unusual noise (squealing, screeching) after assembly, turn it off immediately and check if the brushes are installed correctly. 80% of the time, the reason is because the turbobrush is distorted or a foreign object hits the bearing.

💡

Never turn on the vacuum cleaner immediately after washing - even if parts seem dry. Residual moisture can damage electronic components. It is optimal to wait 24 hours, especially if the room is high in humidity.

Frequent Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes that shorten the life of a vacuum cleaner.

Another common problem is the smell of a vacuum cleaner, which occurs when:

• 🧼 Do not wash the garbage container after cleaning wet waste (e.g. cat toilet).
• 🌿 Organic dust has accumulated in the filter (hair, wool, food residues).
• ☀️ The vacuum cleaner is stored in a wet room (for example, in the bathroom).

To eliminate the smell:

1. Wash the container in a solution of water and vinegar (1:1), then dry thoroughly.
2. Change it. HEPA-filter (if it has been used for more than 6 months).
3. Place a bag of silica gel in the container (it absorbs moisture).

FAQ: Answers to Frequent Questions