Modern Xiaomi Mi TV and Redmi Smart TVs are famous for their stylish design and narrow frames, but their installation often raises questions among users. The main difference between the models of this brand and competitors is the specific design of the mounts, which requires careful attention. Incorrect assembly can lead to damage to the matrix or unstable position of the device on the cabinet.
In this article, we will discuss all the nuances of how to attach legs to a Xiaomi TV to ensure maximum stability and safety of operation. You will learn about the types of screws, sequences of actions and typical mistakes that beginners make when first assembled.
Before you start physical interaction with the device, you need to prepare the workspace. The surface should be flat, wide and, preferably, soft to prevent scratches on the glossy screen or body.
Preparation of the workplace and tools
The first step is to create a comfortable area for assembly. You need a table or a cabinet that is larger than the diagonal of the TV at least by a factor of one. 20-30 This allows you to maneuver the device freely and have access to the mounting holes from all sides.
Make sure the lighting in the room is adequate, as the marking of holes and the direction of screws is often done in fine print or barely noticeable symbols.To work, you will only need a PH2 cross screwdriver, which usually comes with a bundle, but it is better to use a quality tool with a magnetic tip.
It is important to clear the space of foreign objects that may accidentally hit the screen beforehand. If you are unpacking the TV for the first time, save the cardboard box and foam inserts - they may be needed for transportation or warranty maintenance in the future.
Be sure to check the equipment immediately after removing the legs. In the box with accessories should be two supports, a set of screws of different lengths and possibly plastic plugs to hide the fasteners.
Analysis of the design of the Xiaomi stand
The design of the legs on Xiaomi and Redmi TVs may differ depending on the diagonal of the screen and the model year. In most cases, two main types of mounts are used: classic side racks and a central stand for models with a narrow bench.
The side racks are metal or plastic elements that are fixed in special recesses on the bottom of the body, which provide a wide base of support, which is critical for large diagonals. The center leg, in turn, requires more precise alignment, but allows you to place the TV on furniture smaller widths.
⚠️ Warning: Never attempt to place the centre leg on a side-stack model, and vice versa.The geometry of the holes and the weight distribution in these systems are fundamentally different, which can cause the device to fall.
Special attention should be paid to the marking on the inside of the legs. Often the manufacturer applies the designations L (Left) and R (Right), indicating the left and right sides respectively, and ignoring this marking can lead to the legs standing at the wrong angle or holes do not match.
Some Mi TV Stick or compact versions may have universal mounts that allow legs to be mounted both wide and narrow, in which case additional screws are included to vary the width of the base.
Step-by-step instructions for installing side racks
The process of mounting the side supports requires precision and a certain sequence of actions. Place the TV screen down on the prepared soft surface, making sure that there are no solid objects under the screen that can create a pressure point on the matrix.
Put your left leg on the appropriate seat on the body, combine the metal holes of the legs with the carvings in the TV body, insert the screws manually several times to lock the position, but do not tighten them to the end.
Repeat the same procedure for the right leg, make sure that both supports are symmetrically positioned and fit tightly into the body without any skewing, and then you can start the final fixation of the fasteners.
☑️ Installation checklist
Using a screwdriver, tighten all the screws evenly. Move diagonally: pull the top screw of the left leg a little bit, then the bottom screw of the right, and so on, and this will ensure that the pressure is evenly distributed to the body.
The final twisting effort should be moderate, and excessive zeal can disrupt the carvings in the plastic shells, making the mount unreliable, and the screw should be tightened tightly, but without fanaticism.
Installation of the central stand
The center leg is typical for bezeless-designed models or TVs designed to be placed on narrow consoles. Unlike side racks, high positioning accuracy is required here, since the entire mass of the device will fall on one point of support.
Turn over the TV and find the central mounting hole, often with a decorative stub or a special marking in the form of a circle, and remove the protective film with the adhesive of the base of the leg, if it is designed.
Insert the leg into the groove and make sure it falls into place with a characteristic click or stop.Some Redmi TV models use a locking system with a single large screw that passes through the leg into the deep hole of the body.
Twirl the main locking screw using the attached key or screwdriver. Check the stability of the structure by slightly swaying the TV from side to side (holding out the frame, not the screen).
⚠️ Attention: When installing the center leg, it is strictly forbidden to use additional pads or homemade amplifiers. This violates the design load and can lead to the destruction of the mount at the most inopportune time.
If the kit comes with a decorative screw concealment pad, install it after all the puffing work is completed. It is usually fixed to latches or a light adhesive layer.
Table of compatibility of screws and models
One of the common problems with assembly is the confusion in the screws, especially if there are several types of screws in the kit. Below is a table that helps to identify the necessary fasteners for different series of Xiaomi TVs.
| TV series | Type of leg | Size of screw | Number (s) |
|---|---|---|---|
| Mi TV 4A / 4C | lateral | M4 x 10 mm | 4 |
| Mi TV P1 43" | lateral | M5 x 12 mm | 4 |
| Redmi Smart TV X | Central | M6 x 20 mm | 1 |
| Mi TV Q1 | Sideways (wide) | M5 x 14 mm | 4 |
Note that the length of the screw is critical. Using too long a fastener can cause the screw to focus on the internal components of the TV, causing damage to the electronics or screen.
Too short screws will not provide the necessary strength of the connection. If you lose the original kit, select analogues strictly according to the parameters of the thread and length, focusing on the technical specifications of your model.
What if the screw doesn't turn?
Addressing common problems
During operation, users may experience a situation where the TV is wobbly or legs are crooked, most often due to incomplete screws or dust entering the mounting holes.
If you see backlash, try to loosen all the screws again, press the legs tightly against the body and tighten them again diagonally, and make sure there are no gaps between the metal of the legs and the plastic of the body.
In cases where the TV is on a carpet or soft surface, narrow legs can fall through, creating the illusion of instability, in this situation, it is recommended to use a TV stand or a special shelf.
💡
To increase stability on slippery surfaces (glass, gloss), stick small pieces of anti-slip rubber on the lower part of the legs or use ready-made furniture stickers.
If one of the screws is lost or broken, do not attempt to attach the leg to the remaining three.The load asymmetry will lead to the gradual destruction of the remaining mounting points and eventual fall of the device.
In rare cases, the legs themselves are defective, metal curvature. Check the geometry of the supports by placing them on a flat table. If the leg is curved, contact a service center to replace the defective part.
Security and final inspections
Once the legs are successfully installed, you need to do a final safety check, pick up the TV and gently rock it with the side edges, and the design should be monolithic, without creaking or moving elements.
Place the TV in the intended position. Make sure the bench can withstand the weight of the device with a margin. For models with a diagonal of more than 50 inches, it is recommended to additionally fasten the TV or choose a bench with an anti-vandal system.
⚠️ Warning: Do not place the TV near heat sources or in areas with high humidity.This can lead to deformation of the plastic elements of the leg and loss of stability over time.
Make sure that the power cables and HDMI do not strain and put pressure on the hull at the exit points, and the correct installation of the wires is the key to long-term port service and stable signal.
💡
Properly installed legs are a guarantee that your Xiaomi TV will last for many years without the risk of falling or damaging the matrix.
Now that the device is securely in place, you can connect it to the network and enjoy the content. Check the condition of the mounts regularly, especially if there are small children or animals in the house that may affect the TV.