How to glue the video recorder Xiaomi: instructions with photos, errors and life hacks

Xiaomi DVRs are among the most popular gadgets for motorists, thanks to a combination of price, quality and functionality. 70mai The Pro or MiVue 798 is useless if it is not properly secured, and a poorly glued recorder can fall off on the first bump, block the view, or create dangerous glare on the glass. In this article we will analyze all stages of installation - from the selection of a place to the finish check, and also reveal the secrets of professional installers, which guarantee reliable fixation for years.

Feature of Xiaomi registrars – the use of bilateral tape 3M In a set that, when installed correctly, withstands extreme temperatures (from -30°C +70°C) and vibrations. But many users make a critical mistake: glue the device onto dirty glass or can't stand the time of polymerization of the glue. We tested all the ways of attachment on models. 70mai Omni, MiVue 750 and 70mai Dash Cam A800S, And at the end of this article, a unique method of removing old tape without traces that you can't find in the official manuals.

1. Selection of installation site: where to glue the registrar according to GOST and traffic rules

The first step is to identify a mounting area that does not violate traffic rules and does not impair visibility. 7.3) and GOST R 51709-2001, The video recorder should not:

• 🔴 Overlap the driver's view (the area of the windshield, cleaned by wipers, is prohibited)
• 🔴 Be within 15 cm of the steering wheel (may injure in an accident)
• 🔴 Create glare on glass (especially important for models with IR illumination, for example, 70mai Midrive D06)
• 🟢 Allowed areas: upper corner of the windshield on the passenger side or behind the rear-view mirror

The optimal location is the upper right part of the glass (for left-hand cars), at a level of 5-10 cm from the ceiling.

• 📹 Maximum camera angle (140-170)° model-wise)
• 🚗 Minimum hit in the frame of the elements of the cabin (wheel, torpedo)
• ☀️ Protection from direct sunlight (prevents overheating of the matrix)

For recorders with two cameras (e.g, 70mai Omni: the rear module is mounted on the back window in the center, at a level of 10-15 cm from the top edge. Importantly, if the car has a rain/light sensor (usually next to the mirror), the recorder should not block it, this will cause malfunctions in the automatic operation of the headlights or wipers.

⚠️ Note: In some cars (such as Toyota Camry or Hyundai Solar), the windshield has a metallized coating to protect against UV rays. Double-sided tape is worse on this glass - check with a magnet (if it sticks, there is spray). In this case, use a suction mount or a special glue. 3M VHB.

2.Surface Preparation: Why 90% of dumps are due to dirt

The main reason Xiaomi recorders fall off after a week is because they don't properly prepare the glass, even when you don't see fatty finger marks or old glue, they reduce adhesion by 70 percent. Professional installers use 3-step cleaning.

1. Degreasing. Use isopropyl alcohol (90%+) or specialized cleaners (e.g, 3M General Purpose Adhesive Cleaner: Acetone or solvents are not allowed, as they damage the tinting!
2. Mechanical cleaning: To remove microparticles of dust and old glue, use a plastic scraper (companying with some models) or a melamine sponge. The movements should be unidirectional, chaotic friction creating static electricity that attracts dust.
3. Final treatment: Wipe the glass with a lilaless napkin (for example, for glasses) soaked in distilled water, which will remove the residue of alcohol that can evaporate and weaken the glue.

To test the surface, do a test: glue tape to the glass (ordinary stationery) and sharply tear it off. If there are fibers or particles left on it, you need to repeat the cleaning. Ideally, the tape should come off with a characteristic "click" without leaving traces.

3. Fixing the registrar: step-by-step instructions with a photo

Once the surface is ready, we move to fixation. Complete with the registrars Xiaomi comes double-sided tape. 3M (stamp 300LSE It's enough for 1-2 repaintings, so don't make mistakes. Follow the algorithm:

Remove the protective film with the adhesive of the holder base|Attach the holder to the glass and mark the boundaries with a marker|Remove the second protective film from the scotch|Carefully press the holder against the glass, starting from the center|Do not touch the adhesive surface with your fingers|Pressure for 30 seconds for primary fixation|Do not turn on the registrar within 1 hour (full polymerization time)-->

Step 1: Remove the protective film from the base of the holder (not from the tape!) Apply the holder to the glass and circle the circuit with a thin marker (a CD marker is suitable for discs), which will help to position the device accurately.

Step 2. Take the second protective film off the tape. Importantly, don't touch the sticky surface with your fingers, the fat from the skin will reduce adhesion. If you accidentally touch it, re-defat the tape with alcohol.

Step 3: Press the holder against the glass, starting from the center and moving to the edges. This will prevent bubbles from forming. Pressing force should be uniform - use the second finger to support on the back of the glass.

Step 4: Hold the pressure for 30 seconds after fixing, then don't touch the recorder for 1 hour, which is the time it takes for the glue to be fully polymerized. GPS-module can displace the holder.

For models with G-sensor (e.g, 70mai A800S) After installation, check the calibration of the impact sensor:

1. Go to the Registrar menu: Settings → G-sensor → Sizing.
2. Place the device on a flat surface and wait for the process to complete (it will take). ~1 minute).
3. Check the sensitivity by slightly tapping the body - the sensor should activate.

💡

If the recorder is set curve, don't tear it off immediately! heat the scotch with a dryer (temperature 40-50)°C) within 20 seconds, the adhesive becomes elastic and you can adjust the position without detachment.

4.Typical mistakes and how to avoid them

Even experienced drivers make installation errors that lead to flaking of the tape, overheating of the device or loss of shooting quality.-5 problems and solutions:

• 🌡️ "The recorder warms up and turns off. Reason: Direct sunlight hits the body. Solution: Use a sun visor or move the device into the shadow of the rearview mirror. 70mai Pro with Parking Mode function temperature above 60°C can disable recording – install an additional radiator (sold separately).
• 💨 "Scotch fell off after a week." Reason: There was no deep cleaning of the glass or poor-quality glue.Solution: Buy scotch. 3M VHB 4950 (withstanding up to 10 kg per cm2) and repeat the cleaning procedure with isopropyl alcohol.
• 📉 "The camera records the sky/hood, not the road. Cause: Wrong angle. Solution: Adjust the position so that it gets into the frame. 2/3 roads 1/3 Use a laser level or an alignment application (e.g. Bubble Level) to calibrate).
• 🔊 "The recordings are hearing fan noise." Reason: The recorder is set too close to the blower deflectors. Solution: Move the device 10-15 cm left/right of the center or reduce the fan speed in the climate control settings.
• 🚗 "When moving on the bumps, the image shakes." Reason: Weak grip of the holder or wear of the car shock absorbers. Solution: Check the scotch mount (add a second layer if necessary) or use an anti-vibration pad (for example, 3M Anti-Vibration Tape).

⚠️ Note: If you use metallic sprayed film (e.g. LLumar) ATR), double-sided tape may not hold, in which case apply the suction mount to a vacuum pump suction cup or magnetic holder (suitable for metal recorders, such as the MiVue 798).

5. How to remove the registrar without traces: secrets of the masters

Over time, you may need to reinstall the recorder (for example, when selling a car or replacing a model), the main task is to remove the tape without damaging the glass and tinting.

1. Heat. Direct the building hair dryer (or regular hair dryer at maximum power) to the Scotch from a distance of 10 cm Temperature should be 50-60°C (no higher, otherwise the tinting will damage!) Greathe for 2-3 minutes, evenly driving the hair dryer over the surface.
2. Removal. Put a plastic card or a mediator on the edge of the tape, and pull it parallel to the glass, not up, and that minimizes the risk of peeling off the tinting.
3. Clean the residues. 3M Adhesive Remover or vegetable oil (sunflower will do) on the glue residue. After 5 minutes, wipe with a microfibre wipe.

Use a steam generator (if you have access to it) to remove particularly persistent traces. The steam softens the glue in 10-15 seconds, after which it is easily removed with a scraper. Do not use blades or knives - they scratch the glass and damage the tinting!

6. Alternative fastening methods: when scotch is not suitable

If standard double-sided tape is not held (e.g., on leather torpedo or ribbed plastic), consider alternatives:

• 🧲 Magnetic mount, suitable for metal casing recorders (MiVue 798, 70mai A800S). Magnetic holder (e.g., magnetic holder, RAM Mount is attached to the glass on tape, and the recorder is fixed by a magnet (~1500–2500 rubles.).
• 🔧 Suction fixation. Optimal for rented cars or temporary installation. Suction cup should be vacuum (with a pump), not conventional. Examples: Brodit ProClip or Arkon. Important: check the fixation every 2 weeks - over time the vacuum weakens.
• 🔩 Hard bracket, used in commercial vehicles or for heavy recorders (e.g. Xiaomi MiVue 798 with two cameras), bracket mounted to the ceiling by self-tapping screws (drilling required) Plus: maximum reliability. Minus: irreversible changes in the cabin.
• 🧲 Liquid nails glue. Suitable for plastic panels (not for glass!) Use Montage Fix Extreme, which can withstand vibrations and temperature changes. Apply point-by-point so that you don't damage the panel when you dismantle it.

For models with Parking Mode, additional battery power is recommended via hardwire cable, in which case the mounting should be particularly reliable - use a combined method: Scotch. + safety rope (e.g, 3M Safety Cable).

💡

If the recorder is mounted on a torpedo, avoid areas near airbags. When the airbag is triggered, the device can become a dangerous projectile.

7. Installation check: test for reliability and quality of shooting

After fixing the registrar, conduct 3 mandatory tests to ensure that the installation is correct:

1. Vibration test: Start the car and warm up the engine to operating temperature (90)°C. Drive on rough roads (e.g., "slow cop") at a speed of 20-30 km/h. After the trip, check: Has the recorder shifted, is there a backlash in the mount, did artifacts appear in the video (rickety, blurry).
2. Sit in the driver's seat and check if the recorder is closing: Area of action of the wipers, indicators on the dashboard, view through the windshield (especially in turns).

Simple life hack:

Recording test.

Turn on the recorder and record the test video (duration 5-10 minutes).

• Clearness of license plates of oncoming cars (should be read at a distance of 10-15 m).
• No glare from the sun or headlights.
• Correct operation of the G-sensor (when the video is sharply braking, it should be saved to the Event folder).

If the recorder has passed all the tests, the installation is done correctly, if problems are detected, adjust the position or repeat the cleaning / fastening procedure.

FAQ: Frequent questions about installing Xiaomi registrars