Xiaomi smartphones are famous for their performance and quality screens, but over time, even the most reliable equipment requires maintenance. One of the first components to fail during active operation is the battery. Decrease in autonomy is not just an inconvenience, but a signal that the chemical structure of the battery has deteriorated, requiring immediate intervention.
Replacing the battery with Xiaomi is a procedure that a tech-savvy user can do on their own, with the right tools and safety, and it's important to understand that modern phones are monolithic, with access to the insides limited by adhesive frames and a complex system of plumes, and that doing the wrong thing can damage the display or motherboard.
In this article, we will take a closer look at the process of diagnosing, selecting a new battery, and the step-by-step algorithm for replacing it. You will learn what nuances exist in different models, from budget Redmi to flagship Mi, and how to avoid the common mistakes that beginners often make when opening the body for the first time.
Diagnosis of battery status
Before disassembling the device, make sure that the problem is precisely the wear of the battery, not software failures or a fault of the charge controller. Android provides basic monitoring tools, but for accurate data it is better to use an engineering menu or specialized applications. Type ##6485## in the dialer code to see the technical power settings.
Pay attention to the indicators MB_06 (battery status; and MB_00 (If the status bar says "Bad" or "Replace", it's a direct signal to replace. It's also worth paying attention to the physical condition of the housing: if the back cover starts to move away or the screen goes waves, the battery swells.
⚠️ Warning: If you notice a bloating battery, immediately stop charging the device.The pressure inside the housing can damage the display matrix or cause fire when mechanically exposed.
For a deeper analysis, you can use applications like AccuBattery or Ampere, which allow you to track the actual capacity in milliamp hours and compare it with the declared manufacturer, and losing more than 20% of the original capacity is considered critical for comfortable use of a smartphone during the day.
Tools and training required
A good battery replacement with Xiaomi is impossible without the right tools. Using inappropriate items like knives or needles greatly increases the risk of damaging plumes or puncture the battery itself. You will need a set of precision screwdrivers, usually the PH000 and Y000 types, since the screws in Xiaomi can be of different shapes.
To open the case safely, you need a hair dryer or a special heating pad to soften the glue, and the adhesive that holds the back cover or display module becomes elastic when heated, allowing you to carefully separate the parts without chipping, and you will also need plastic blades (mediators) and a suction cup to lift the glass.
☑️ Battery replacement tools
Make sure to prepare the workspace. It should be well lit and not conduct static electricity. It is recommended to use an antistatic mat or at least work on a clean wooden surface, avoiding synthetic fabrics. Make sure that you have a new adhesive in advance, as the old one loses its properties after heating.
Original battery selection and compatibility
The component market is full of offers, but finding a really high-quality battery for Xiaomi is not easy. QR-The use of cheap analogues often leads to rapid decrease in capacity and incorrect display of percentages of charge.
When choosing a model, consider the model code, which usually starts with the letters BM (e.g. BM39, BM46) and which should match the marking of your old battery. Even if the battery is physically fit, the difference in voltage or contact location can knock out the power controller.
| Parameter | Original | Quality copy | Cheap analogue |
|---|---|---|---|
| Cycle resource | 500-800 cycles | 300-400 cycles | Less than 200 cycles |
| Protection against overheating | Complete. | Basic | Often absent |
| Real capacity | 100% of the claimed | 80-90% of the claimed | 50-60% of the claimed |
| Term of service | 2-3 years | 1-1.5 years | 3-6 months |
Buy components only from trusted suppliers who are willing to provide a warranty. Never purchase batteries without individual packaging and protective film on contacts, as this is a sure sign of poor quality or long-term storage in inappropriate conditions.
The process of disassembling the smartphone
Start disassembling only after the device is completely turned off. Heat the perimeter of the rear cover or display (depending on the design of your Xiaomi model) to a temperature of 60-70 degrees Celsius. Don't hold the hair dryer too close to overheat the matrix or plastic frame. Movements should be uniform throughout the perimeter for 2-3 minutes.
Using a suction cup, create a small gap between the body and the lid, then gently insert a plastic mediator. Drive the tool along the body, cutting the adhesive layer. Be extremely careful in the areas where the plumes are located, usually in the bottom or side where the fingerprint scanner is located.
⚠️ Warning: Do not try to cover the lid with metal tools.One awkward movement can lead to a crack in the glass or short circuit of the internal components.
Once the back panel is removed (or the display module if the unibody design is removed), the insides will be accessed, and the first thing you need to do is to disconnect the battery plume from the motherboard, and then carefully bend the locking connector with a plastic blade, and only after the power is turned off, you can continue working with other components.
What to do if the lid does not open?
Battery replacement and assembly
The old battery in most Xiaomi models is fixed to double-sided tape, which can be extracted using a special hood with a suction cup or gently tampered with a plastic card, and it is strictly forbidden to puncture the battery or bend it, as this will cause a chemical reaction and possible fire.
Clean the seat of old glue residues with alcohol or a special solvent. Apply a new glue (such as the B-7000) in a thin layer on the frame of the new battery and insert it into the niche. Press the cell tightly for a few minutes for primary fixation. Connect the plume to a characteristic click.
💡
Before you finish the case, turn on your phone and check the touchscreen response and vibration, which will make sure that all the plumes are connected correctly, without fully assembling the device.
The assembly is done in reverse order. Make sure that all screws are screwed into their places, as they can be of different lengths. The back cover or display module also needs to be fixed with new glue or special adhesive tape, ensuring that the body is tight. Leave the device under the press (you can use books or clips) for 1-2 hours for polymerization of the glue.
First launch and calibration
Turn on the smartphone after assembly. The first run can take longer than usual, because the system needs to recognize a new power source. If the phone is on, immediately charge it to 100%. Do not use the device intensively in the first hours of the new battery.
To properly operate the charge indicator, it is recommended to perform a calibration procedure: discharge the device until completely shut down, then charge it to 100% when switched off. Then turn on the phone without turning off the charger, and make sure that the indicator shows full charge. Repeat the cycle 2-3 times for best result.
In some cases, after a battery change, the system may issue a warning about a non-standard battery, which is common when you install high-quality copies. If the phone is stable, this message can be ignored, it will disappear after several charge-discharge cycles.
💡
Proper calibration in the first days of using a new battery extends its life and ensures an accurate display of the percentage of charge in the system.