How to get it right SIM-Map from the smartphone Xiaomi: detailed instructions with photos and videos

Extraction SIM-Xiaomi’s smartphone cards may seem like a simple task, but in practice, users often face difficulties, from jammed trays to the fear of damaging contacts.+ Xiaomi 13 Ultra, where two devices are installed simultaneously SIM-In this article, we will analyze all possible scenarios - from standard extraction to emergency situations when the tray does not extend or the smartphone does not respond to buttons.

It is important to consider that the design of trays Xiaomi differs depending on the year of release and series. For example, flagship models Xiaomi 14 and Xiaomi Mix Fold 3 are equipped with enhanced locking mechanisms, and budget Redmi A2 or POCO M6 Pro can have more fragile plastic latches. We will dwell on the nuances for each category of devices, as well as give recommendations for the choice of tools and care for contacts after extraction.

Preparation for extraction SIM-maps: what you need to know

Before you start retrieving, make sure the smartphone is turned off, which will prevent accidental taps on the screen and reduce the risk of short circuits when in contact with metal tools.

• 🔧 Availability of a paper clip for extraction (or a special key that comes with some models, for example, Xiaomi) 13T Pro).
• 📱 Location of the tray - in most models it is on the upper or lateral edge, but in the POCO F5 redmi K60 maybe from below.
• 🔋 Battery level – if the smartphone is less than 20% dead, it is better to recharge it before manipulation to avoid sudden shutdown.

If you have a hybrid slot model (like the Redmi Note 11 Pro+ 5G), remember the order of card installation: usually the first slot is for nano-SIM, and the second slot is for nano-SIM or microSD. By confusing them with places, you risk damaging contacts or getting a “No Network” error after rebooting.

⚠️ Warning: Never use sharp objects (needles, knives, toothpicks) to remove the tray, which can damage the slot's sealing ring, causing dust and moisture to enter the enclosure. IP53 (for example, Xiaomi 12T) This will cancel the warranty for water protection.

Standard method: extraction by means of a paper clip

This is the most common and safe method, suitable for 90% of Xiaomi models, including the Redmi 10C, POCO X5 Pro and Xiaomi 12 Lite.

1. Find on the case of the smartphone a small hole next to the tray for SIM-It can be indicated by the pictogram of the card.
2. Put a straight clip (or key from the kit) into the hole all the way through. Press it with effort, but without fanaticism, it should come out with a slight click.
3. The tray will extend 2-3 mm. Carefully pull it with your fingers until completely removed.
4. Delete. SIM-card, if necessary, replace it or clean the contacts with dry soft cloth.

If the tray doesn't retract the first time, try swaying the clip slightly in the hole or changing the angle of press. In Xiaomi Civi 3 and Redmi K50i models, the locking mechanism can be tighter than on budget devices.

Turn off the smartphone.|Prepared a paper clip or key|Checked the tray's location.|Made sure there was no moisture on the body.|Photographed the order of card installation (for hybrid slots)-->

Important nuance: In some models (for example, Xiaomi 11T Pro) tray is fixed not by a spring mechanism, but by a plastic latch. If you feel resistance when pressing a paper clip, do not make excessive efforts, you should contact the service center.

What to do if the tray is jammed or not pushed out

The situation when the tray does not respond to the pressing of the paper clip, occurs in 5-7% of users.

• 🔧 Deformation of the mechanism after the fall of the smartphone (often happens in the case of a smartphone) POCO M4 Pro with plastic case).
• 💦 Getting moisture or dust into the slot (relevant for models without certification) IP).
• 🔄 Incorrect installation SIM-cards in previous retrieval (for example, skewed the microSD card in a hybrid slot).

If the tray is not pushed, try the following methods (from the safest to the radical):

1. Heat the case. Heat the area around the slot with a hair dryer (temperature no higher than 50°C) for 1-2 minutes. The heat will expand the plastic, and the mechanism can unlock. Suitable for the Redmi 9A and other models with a plastic case.
2. Using the vacuum method, put a suction cup (like a phone holder) on the tray and pull it, and it works if the tray is 1 to 2 mm out, but not completely.
3. Disassembly of the body. The last option is to remove the back cover (this will require a mediator and heating), Relevant for the Xiaomi Mi 11 and other models with a removable cover.

⚠️ Note: If the smartphone was in water or humid environment, do not try to remove the tray yourself. corrosion of contacts can lead to short circuit when mechanically exposed.

Features of extraction SIM-Maps in different Xiaomi series

The design of the trays varies depending on the series and year of release of the device, the table below shows the key differences:

For models with a metal body (for example, Xiaomi 13T) it is recommended to use a stainless steel clip - it is less prone to deformation. In plastic cases (Redmi 10A), you can even do with a plastic pin, but you need to act extremely carefully.

💡

If you often get out SIM-card (for example, for trips abroad), lubricate the slot sealing ring with silicone lubricant.This will prevent dust accumulation and make it easier to extract. Do not use oils based on petroleum products - they can damage the plastic!

How to extract SIM-Map without paper clips: alternative methods

If you don't have a paper clip or a special key, you can use the tools at hand, the main rule is that the object should be thin, durable and not sharp.

• 📎 Hair clip (untighten it and break the tip 2-3 cm long).
• 🖊️ The gel pen rod (remove the writing knot and use a plastic tube).
• 📌 A pin or English pin (blank the tip with sandpaper).
• 🎧 Headphone pin (for example, from Xiaomi Hybrid Pro).

Inappropriate items that can damage your smartphone:

• ❌ Needles (too sharp, can pierce the sealer).
• ❌ Knives or scissors (risk of scratching the body).
• ❌ Dental cleanings (may break inside the hole).

To extract without tools in extreme cases, you can try the method of heating and tapping:

1. Heat the case of the smartphone in the area of the slot with a hairdryer (1-2 minutes).
2. Carefully tap the edge of the tray with the blunt side of the pencil.
3. Try to push the tray with your nail or credit card.

⚠️ Note: If the smartphone is warranty, avoid methods related to disassembly or heating. Xiaomi service centers have special tools to extract trays without damage, and repair warranty in this case will be free of charge.

Cleaning contacts and caring for the slot after extraction

After extraction SIM-It is recommended to carry out preventive cleaning of contacts:

• 📶 Smartphones often lose their network (No Service).
• 🔄 SIM-The card is not determined after rebooting.
• 💦 The device was in a humid environment.

You'll need to clean:

• 🧴 Alcohol wipes (or cotton swab dipped in isopropyl alcohol).
• 💨 Compressed air container (to remove dust).
• 🔍 Lupa (to inspect contacts for oxidation).

Step-by-step:

1. Wipe your contacts. SIM-- Do not push the contacts, move along the contacts without pressing too hard.
2. Blow the slot with compressed air (hold the balloon vertically to avoid moisture).
3. Check your contacts for green coating. If you have one, use an eraser to clean it up.
4. Allow the slot to dry for 10-15 minutes before installation SIM-map.

In Xiaomi 12S and newer pins, the tray is covered with a protective layer that can be damaged by aggressive cleaning. Use only soft materials (microfibre, cotton swabs).

💡

Regular cleaning of contacts SIM-Cards (every 3-6 months) extend the life of the communication module and prevent network problems, especially for smartphones, which are often used in dusty or wet conditions.

Frequent Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes when extracting. SIM-And the cards that cause the breakdowns are the most common:

1. Installation SIM-The contacts should be on the back of the smartphone. POCO X4 Pro and Redmi Note 11S There is a pictogram on the tray showing the correct position.
2. Using force in a jammed tray can break a plastic lock or bend metal guides. In the Xiaomi 11 Lite NE, a tray is attached to the motherboard - excessive force will damage it.
3. Extraction SIM-cards with the smartphone on, and in rare cases, this can cause a modem to malfunction, especially in devices with a mobile device. 5G (For example, Xiaomi 13 Pro).
4. Moisture entering the slot after cleaning. Always let the contacts dry before installing the card. Moisture can cause corrosion, leading to persistent errors "SIM-card not supported".

If, after extraction, SIM-The smartphone has stopped seeing the network, follow the following steps:

1. Reset the device.
2. Check if the Flight mode is on in the notification curtain.
3. Go to Settings. → SIM-maps and mobile networks → Name of the access point (APN) Reset the settings to standard.
4. If the problem persists, try inserting it. SIM-card in another smartphone to check its performance.

FAQ: Answers to Frequent Questions