How to get it right SIM-Map from the Xiaomi phone: 3 proven ways

Extraction SIM-Xiaomi smartphone cards seem like a simple task, but in practice users face typical problems: a jammed tray, a lost key or a fear of damaging the device. In this article, we will discuss all the current methods, from standard extraction with a special key to emergency methods for models without tools, POCO and flagship Xiaomi, where the location of the slot may differ.

It is important to understand that incorrect actions (for example, using sharp objects instead of a key) often lead to breakage of the slot contacts or getting debris inside the case. We have put together proven methods that work even for older models like the Redmi Note 4 and new flagships like the Xiaomi 14 Ultra. SIM-Whether you are afraid to break something, this guide is for you.

Preparation: What to Know Before Extracting SIM-map

Before you start retrieving, make sure the phone is turned off.This is not a requirement for all models, but for devices with hybrid slots (like Redmi). 9A, where SIM And microSDs share a tray, and power outages minimize the risk of short circuits when contacts are accidentally touched:

• 🔍 Slot type: Most Xiaomi has a retractable tray (requires a key), but in rare models (e.g., a key, POCO F1) Maybe a removable back cover.
• 🔑 Key availability: standard tool comes with the phone. If you lose it, use a clip or pin of the same diameter (0.8-1 mm).
• 📱 Slot location: 90% of models have it on the top or side edge, except for the Xiaomi Mi Mix (bottom edge) and some Black Shark (under the removable lid).

If you are planning to replace SIM-Prepare it in advance: for Xiaomi suitable nano-SIM (12.3×8.8 In hybrid slots (e.g. Redmi Note) 12 Pro+) You can install either two nano-SIMs or one. SIM + MicroSD: Using micro-SIM adapters in nano-slots can damage contacts – the phone may stop recognizing the card.

⚠️ Warning: Don't try to pull the tray out by force if it doesn't yield. - Xiaomi models 12T and newer is used a mechanism with a spring - excessive pressure can bend the metal frame of the slot.

Method 1: Standard key extraction (for 95% of models)

This is the basic method that works for all modern Xiaomi smartphones, including Redmi, POCO You'll need the original key (or replacement, a paper clip, an unbended stationery bracket:

1. Find the extraction hole on the side or top of the phone, which is located next to the tray and is usually marked with an icon. SIM.
2. Insert the key into the hole at a 90 degree angle to the body. Press with enough force to trigger the spring mechanism (you will feel a slight click).
3. Once you click, the tray will move 2-3 mm -- gently pull it with your fingers to the end. Don't make an effort if it doesn't go!
4. Get it. SIM-If necessary, replace it or clean the contacts of the tray with a dry wipe. Set the tray back, slightly pressing until you click.

If the tray is not moved the first time:

• 🔄 Check if the key is skewed - it must enter the hole strictly perpendicular.
• 🛠️ Try to shake the key slightly left-right without removing it from the hole.
• 💡 Light the hole with a flashlight – it may have been dust or debris inside.

Check if the phone is turned off (recommended)

Prepare the key or replacement (clip, pin)

Find the hole to extract (usually on the upper/side face)

Make sure the tray is not blocked (no physical damage)-->

In dual slot models (such as the Xiaomi 13 Pro), the tray can have two notches for the game. SIM-Make sure you pull out the card you want -- they're often labeled as SIM1 and SIM2.

Method 2: Keyless extraction (alternative methods)

If you lose your key, don't despair. There are several safe ways to extract the tray without a specialized tool. The main rule is not to use sharp objects (needles, knives, toothpicks) that can scratch the body or damage the mechanism.

Method 1: Paperclip or pin

The most reliable key substitute is an unbended paper clip or a stationery pin, the diameter must match the original key (about 0.8 mm).

1. Untighten the paperclip so that a straight segment of 3-4 cm is obtained.
2. Put it in the hole to extract and press until you click.
3. If the paperclip is too thin, wrap its end with tape for density.

Method 2: Tape or thread (for trays without a lock)

Suitable for older models (e.g. Redmi) 3S), where the tray has no spring mechanism, but simply inserts into the grooves. You need a thin duct tape (scotch) or a strong thread:

1. Stick a piece of tape to the end of the tray (where it protrudes from the body).
2. Carefully pull the ribbon - the tray should come out of the grooves.
3. For thread: snag it in the gap between the tray and the body and pull on yourself.

Method 3: Vacuum capture (for removable covers)

If you have a removable back cover (for example, POCO X3 NFC), You can use a suction cup for phones:

1. Limit the suction cup to the lid next to the slot.
2. Pull the lid up - it will move, opening access to the tray.
3. Extract. SIM-map and set the lid back, pressing until clicking.

⚠️ Warning: Don't use tweezers or pliers to pull the tray - this deforms metal guides. Xiaomi service centers often see phones with bent slots after such manipulations.

Standard key from the kit

Paperclip or pin

Tape/strand

I'm going to the service center.-->

Method 3: Extract SIM-maps in removable-lid models

Some Xiaomi models and POCO (for example, POCO M2, Redmi 8A) They have a removable back cover under which there are slots for SIM-In this case, the process is simplified, but requires caution:

1. Turn off the phone and place it on a flat surface with the screen down.
2. Find a latch or slot to open the lid, usually located at the bottom of the case (near the charging connector).
3. Put the lid on your nail or plastic card (like a bank card).
4. Remove the lid from the bottom corner. It should detach with a characteristic click.
5. Extract. SIM-You can pull up a card from the slot, and you can see the direction of the contacts, they have to look down.

When you put the lid back in, make sure all the latches are in place. If the lid is not fixed, check:

• 🔄 Correct location SIM-cards (it should not be outside the edge of the slot).
• 🧲 Magnetic contacts (in some models they are responsible for fixation).
• 🚫 No debris or dust on the sealing gum (if any).

In models with a battery under the lid (for example, Redmi). 7A) Be careful not to touch the battery contacts with metal objects.

💡

If the lid sits tightly and does not lend itself, heat it with a hair dryer at a minimum temperature (30-40).°C) for 10-15 seconds, the heat will make the plastic more elastic and it will be removed more easily.

Frequent Mistakes and How to Avoid Them

Even when the procedure seems simple, users often make mistakes that lead to breakdowns, and we've collected the most common cases and ways to prevent them:

Pay special attention to hybrid slots (for example, in Xiaomi). 11T Pro. If you use two SIM-If you want to use a microSD card, remember that one of the SIM-The card must be removed. SIM This means that the phone will not see any of them.

Another common problem is a jammed tray, and if it doesn't extend even after you press the key, don't try to pull it out with pliers. You'd better go to a Xiaomi service center, where experts will disassemble the case and remove the tray without damage, and the average cost of this service is 500-1000 rubles.

Features of extraction SIM-Maps in popular Xiaomi models

The design of slots can vary depending on the series and year of release of the phone, we have collected key nuances for the most common models:

Redmi Note 10/11/12 series series

In these models, the tray is on the top of the left.

• 🔧 A standard key with a diameter of 0.8 mm is used.
• 📶 Hybrid Slot: either 2 nano-SIM or 1 nano-SIM + microSD.
• ⚠️ The tray is a little tight - don't be afraid if it doesn't come out the first time.

Xiaomi 13/14 Series

The flagship models have a tray on the right side.

• 🛡️ Mechanism with reinforced spring - do not press too hard.
• 📱 Only nano-SIM (microSD not provided).
• 🔄 Replacement SIM-Maps may need to be rebooted to activate the network.

POCO F/X series

In most models POCO (for example, POCO X5 Pro) the tray is on the left side:

• 🔑 The key is often plastic – use a metal clip for reliability.
• 📡 In some models (for example, POCO F4 GT) slot is located under the removable cover.
• 🚫 No eSIM support (physical cards only).

Xiaomi Mi Mix Series Series Series Series

The unique thing about these models is the tray on the bottom of the right.

• 🔧 Removal hole is smaller than standard – use a thin paper clip.
• 📵 When removing the tray, the screen may slightly rise (due to the frameless design).
• ⚠️ Don’t make an effort if the tray doesn’t go – in these models it bends easily.

What to do if SIM-card stuck in the slot?

The situation when SIM-The card gets stuck in the slot, it's less common, but it can happen when you're not tidy:

1. Don't panic or try to pull the card out by force.
2. Turn off your phone to avoid short circuits.
3. Take flat-ended tweezers (not sharp!) and gently slap the card over the edge. If there are no tweezers, use a plastic card (bank or discount).
4. If the card does not lend itself, try to slightly sway the tray left-right, while pulling the card up.
5. In extreme cases, remove the back cover (if it is removable) and remove the card from the battery side.

If the card is broken inside the slot (for example, a piece of plastic broke off), do not try to remove it yourself. Contact the service center - they use special tools to clean contacts. The average cost of removing debris is 800-1,500 rubles.

⚠️ Note: If after removing the stuck SIM-If you need to, check the slot's contacts for damage, clean them with alcohol and a soft brush.

💡

Never use glue or tape to fix. SIM-This can cause glue to the contacts and cause the communication module to break permanently.

FAQ: Frequent questions about SIM-maps in Xiaomi