How to Clean the Xiaomi Mi Robot Vacuum Robot Cleaner V10: detailing

Why Xiaomi Cleanups V10 — It's not a luxury, it's a necessity.

Xiaomi Mi Robot Vacuum Robot Cleaner V10 — One of the most popular cleaning assistants, but even the most advanced equipment requires care. Many users mistakenly think that it is enough to empty the garbage container, but clogged filters, hair on rollers and dust in the sensors can lead to a drop in suction power, navigation errors and even engine failure. Regular cleaning not only maintains high performance, but also prolongs the life of the vacuum cleaner. 30-40% Compared to devices that are operated without maintenance.

In this article you will find step-by-step instructions with photos, how to disassemble and clean all key nodes Xiaomi V10, We will also reveal common user errors (such as why you shouldn't wash) HEPA-filter under running water) and give recommendations on the frequency of service depending on the intensity of use, if your vacuum cleaner started to pick up garbage worse, hums louder than usual or gives an error 02-03-00 — This will help you to return to life without going to the service center.

Before you start, prepare the necessary tools:

• 🧴 Soft brush (a toothbrush or a makeup brush is suitable)
• 🧽 Dry microfiber cloth (without pile!)
• 🔧 Flat screwdriver (for removing side brushes)
• 💨 A compressed air cylinder (optional, for blowing out hard-to-reach places)
• 🧼 Alcohol wipes (for cleaning sensors)

Preparation of the vacuum cleaner for cleaning: what to do before disassembly

The first step is to completely disconnect the vacuum cleaner from the power supply. Remove the battery (if you plan to clean the contacts) or simply turn off the device with a button on the case. This will prevent accidental switching on during maintenance. We also recommend resetting errors in the Mi Home app if there are any: sometimes after cleaning the sensors, the vacuum cleaner "forgets" about past failures.

Next, check:

• 🔋 Battery charge: if the level is below 20%, it is better to recharge - some parts (for example, the main roller) are removed easier when power is turned on.
• 📱 App status: Write down the current map and cleaning area settings, as recalibration may be required after cleaning the sensors.
• 🗑️ Type of garbage in the container: if there is a lot of moist dirt (for example, after cleaning the kitchen), immediately rinse the container with warm water and soap.

⚠️ Note: Never use Xiaomi to clean up V10 Water filter vacuum cleaner or steam generator! Moisture on a control board or LiDAR sensors can cause a short circuit. To remove dust from electronic components, use only a dry brush or compressed air.

If the vacuum cleaner has made errors of the type 05-01-00 (sidebrush problem) or 02-03-00 (You have a clogged filter, you take a photo of the screen with the code, and this will help the later identify the problem node, and it's also useful to capture the disassembly process on video: some latches on the case. V10 They are fragile and easy to break when first dismantled.

Cleaning the container for dust and filters: Step-by-step with a photo

The garbage container and filters are the lungs of your vacuum cleaner, and their pollution directly affects the suction capacity and the quality of cleaning. V10 a two-stage filtering system is used: a primary filter (a grid inside the container) and HEPA-filters, they need to be cleaned differently!

Step 1: Removal of the container

Press the release button on the back of the vacuum cleaner and pull the container over you. Inside, you'll see:

• 🗑️ Main garbage compartment (washed with water)
• 🧹 Primary filter-net (cleaned with a brush)
• 🌀 Cyclone separator (purged with air)

Step 2: Clean the primary filter

You can't wash the mesh with water -- it can deform! Remove the dust with a soft brush, then blow the compressed air on the back. If the filter is heavily clogged (for example, after cleaning construction dust), gently tap it on the hard surface.

Step 3: Flushing HEPA-filter

It's the most capricious element. HEPA-filter V10 You can't wash it with water. You can only vacuum it (at minimum power) or blow it with air. If the filter is damaged or has been in operation for more than 6 months, replace it. ZSTYJQ02ZM.

⚠️ Warning: After washing the container, be sure to dry it 24 hours before installing it back! Wet debris inside can cause metal parts to corrosion and turbine failure. If in a hurry, use a cold blower.

Remove the container with a button on the body|Clean the net with a brush (Do not wash!)|Wash the container with warm water|Dry all the details 24 hours|Blow through HEPA-compressed-air filter-->

Cleaning the main roller and side brushes: remove hair and threads

The main roller (brush with bristles) and side rotating brushes are the most vulnerable parts of Xiaomi V10. The hair, threads and fur of animals are wound on the axle, which leads to overheating of engines and errors such as: 05-01-00 (You need to clean them at least once. 1 weekly with intensive use.

Step 1 Removal of the main roller

Turn the vacuum cleaner over and find the two latches on the sides of the main brush, press them simultaneously and pull the roller over you. Inside, you'll see:

• 🌀 Central shaft (often wrapped in hair)
• 🔴 Red markings (show correct position when installed)
• ⚫ Black gears (cannot be lubricated!

To clean the roller:

1. Cut off large clusters of hair with scissors.
2. Wash the bristles with warm water and soap (no more than 40)°C!).
3. Dry the roller vertically so that water does not get into the bearings.
4. Clean the axis with a liquor wipe.

Step 2. Side brushes.

The side brushes are mounted on a single screw (under a flat screwdriver). Carefully unscrew it and remove the brush.

• 🧶 Hair between bristles (use tweezers)
• 🔄 Axis of rotation (air blown)
• 🔌 Contact (wipe with alcohol)

If the bristles are worn by more than 50%, replace the brush (article) ZSTYJQ01ZM). Do not use brushes from other Xiaomi models (for example, from the same model). V8 or V11) — They have a different diameter and can damage the body!

💡

To make your hair less coiled on the roller, brush the carpets with a hard brush before cleaning, which will reduce the load on the brushes and prolong their life.

Cleaning sensors and LiDAR: why the vacuum cleaner “blind” and beats on furniture

If you're Xiaomi. V10 He's got a problem with his sensors, and he's got a problem with his spatial orientation, skipping areas, or hitting obstacles:

• 🔦 LiDAR (laser rangefinder on the "turret")
• 👁️ Optical sensors (bottom of the case)
• 🧲 Fall sensors (on edges)

LiDAR cleanup:

The glass on the "turret" should be perfectly clean. Rub it with an alcohol napkin in circular motions, then blow the hole with compressed air. Never use abrasives (such as paper towels) - they scratch the glass, which leads to distortion of the laser beam and errors in map construction.

Optical sensors:

On the bottom panel of the vacuum cleaner, you'll find 4 small windows that you need to clean with a dry cotton swab dipped in alcohol, and if the sensors are dirty, the vacuum cleaner can:

• 🚫 Not seeing black carpets (thinks it's a chasm)
• 🔄 Spinning in one place
• 🛑 Suddenly stop

Fall sensors:

They're on the sides of the case, blow them in air and check if there's any dust inside, and if the sensor is clogged, the vacuum cleaner will be afraid to go to the edges of the stairs or high thresholds.

Turbine and duct maintenance: when the vacuum cleaner "coughs" garbage

If Xiaomi V10 He starts spitting garbage during cleaning or makes an uncharacteristic whistle, a problem in the turbine or ducts, which is a serious signal, ignoring which can lead to engine burnout (the cost of repair is up to 70% of the price of a new vacuum cleaner!).

Causes of blockages:

• 🍃 Large debris (leaves, pieces of paper)
• 🧵 Threads/hair in the turbine
• 🏠 Construction dust (cement, gypsum)

How to clean:

1. Unplug the garbage container.
2. Remove the turbine cover (unscrew 2 screws on the bottom panel).
3. Remove debris from the turbine blades with plastic tweezers (the metal may scratch).
4. Blow the duct from the container to the turbine.
5. Collect in reverse order, check the tightness of the connections.

⚠️ Warning: If you find that the turbine blades are deformed or chipped, stop using the vacuum cleaner immediately! This is a sign of hard objects (nuts, stones), and further work can lead to the destruction of the engine. MSXJQ03ZM).

After cleaning the turbine, run the vacuum cleaner at maximum capacity without a container (for 10 seconds) to remove the dust residue from the ducts. If the whistle remains, check the sealing gums between the container and the housing: they may have deformed or lost elasticity.

💡

Regular cleaning of the turbine (every 3 months) prevents 90% of breakdowns associated with loss of suction power.

Cleaning contacts and battery: why the vacuum cleaner does not hold the charge

If Xiaomi V10 It is quickly discharged or not charged before 100%, The problem may lie in oxidized contacts or a contaminated battery compartment, and over time, lithium-ion batteries lose capacity, and it is recommended to replace them once in a while. 2-3 year-end.

Clearing contacts:

The charging contacts are located on the back of the vacuum cleaner and on the docking station.

• 🧴 Alcohol napkin (to remove oxidation)
• ✏️ Swallow (for polishing contacts)

Battery maintenance:

Battery in V10 It's not removable, but you can:

1. Blow the compartment with compressed air (remove dust).
2. Check the battery status in the Mi Home application (Settings) → Battery status).
3. Perform a full cycle of discharge / charging once a month (0% → 100%) for calibration of the controller.

If the battery capacity has fallen below 60% of the nominal (checked through Settings) → Battery, consider replacing. Original battery has articular MDY426050 (2600 mAh).

Frequent mistakes when cleaning Xiaomi V10: what can't be done

Many users accidentally ruin their vacuum cleaners by following "advice from the Internet."-5 miscarriage:

• 🚫 Wash HEPA-water-block → It loses its properties and starts to pass fine dust.
• 🚫 Lubricate moving parts (wall, brushes) → lubrication collects dust and clogs the machinery.
• 🚫 Use a vacuum cleaner to clean liquids → This will cause the turbine to corrosion.
• 🚫 Dry details with a hair dryer in hot air → plastics can be deformed.
• 🚫 Disassemble LiDAR without experience → Laser module is sensitive to static electricity.

Also avoid:

• 🧲 Storage of the vacuum cleaner at the docking station without recharging (the battery is discharged to 0%, which reduces its service life).
• 🌡️ Cleaning at temperatures below 5°C or higher than 40°C (this damages the battery).
• 🔌 Use of non-original chargers (can burn the power controller).

If you doubt your abilities, contact the authorized service center Xiaomi. + diagnosis) usually does not exceed 1500-2000 RUB, which is cheaper than repair after an unsuccessful self-disassembly.

FAQ: Answers to Frequent Questions