The screen on Xiaomi itself is pressed: what to do and how to fix the problem

Have you noticed that your Xiaomi screen spontaneously opens apps, scrolls pages or presses buttons without you? This is a common problem that can turn smartphone use into a nightmare, and the reasons for this behavior range from software failures to hardware malfunctions, and you can not ignore them — over time, the situation can worsen to the complete loss of the device.

In this article, we will examine all possible reasons why the Xiaomi screen itself is pressed, from the banal contamination of the display to serious damage to the plume. You will receive step-by-step diagnostic instructions, as well as ways to troubleshoot both software methods (without data loss) and hardware (if you can not do without repair). 10/11/12, POCO X3/X4/X5 and flagships Xiaomi 12/13/14, where the problem is most often encountered.

Before you bring your phone to the service center, try to go through our checklist - in 70% of cases, the problem is solved independently in 10 to 30 minutes.

1.Why Xiaomi's screen is pressed itself: the main reasons

Spontaneous taps on Xiaomi's screen rarely occur without a reason, most often a combination of several factors that can be divided into software and hardware. Let's take a closer look at them.

Among the programmatic reasons are the following:

• 🔄 Failures in firmware MIUI — Especially after the updates or incorrect installation of custom ROM.
• 📱 Application conflict – some programs (such as launchers or optimizers) can intercept the wheelbarrows.
• 🦠 Viruses and malware – Trojans are able to emulate clicks to display ads or steal data.
• 🔧 Incorrect sensor settings – for example, the enabled “Touch with gloves” function or increased sensitivity.

Hardware causes are usually more serious:

• 💧 Moisture falling under the screen or on the plume – even microscopic drops can cause false positives.
• 🔌 Display plume damage is a common problem after falls or careless disassembly.
• ⚡ Static electricity – accumulates when using non-original chargers.
• 📱 Wear of the touch layer - relevant for older phones 3–4 years (e.g. Redmi Note) 8/9).

Fun fact: on the Mi Community forums, users complain about spontaneous taps at the bottom of the screen (navigation button area), because this is where the most vulnerable area of the plume passes.

Quick diagnosis: how to determine the cause

Before you start repairing, you need to understand what causes false pressing.

1. Phone reboot – sometimes the failure is temporary and disappears after the reboot.
2. Checking in Safe Mode – if the problem has disappeared, the third-party app is to blame.
3. Sensor Test – Use the code ##6484## (for some Xiaomi models) or the Touch Screen Test app.
4. Visual inspection – check if there are cracks, swelling or traces of moisture under the glass.

If the screen reacts to presses even when it is turned off (for example, when connecting to a charge), it is almost guaranteed a hardware malfunction, and if the problem only manifests itself in certain applications (for example, Instagram or TikTok), the software is to blame.

💡

If the spontaneous taps occur only in games (for example, in the PUBG Mobile or Genshin Impact, try turning off the Tactile Feedback feature in the game settings. Sometimes the vibration of the motor creates false sensor alerts.

3. Software methods of solving the problem

If the reason lies in the software, try the following methods without losing data:

Calibration of the touch screen

On some Xiaomi models (e.g. Redmi 9 or X-rays) POCO M3) There's a hidden calibration menu to get there:

1. Open the Phone app.
2. Enter the combination ##2664##.
3. Follow the instructions on the screen (usually touch the targets several times).

If the code doesn’t work, use third-party utilities like Touchscreen Calibration from Google Play.

Resetting sensor settings

Sometimes it helps to reset the input parameters:

1. Go to Settings. → System system → Additionally. → Special facilities → Touch settings.
2. Turn off the touching options in gloves and increased sensitivity.
3. Back to Settings → Annexes → Manage applications and clear cache for System interface MIUI.

Removal of problematic applications

Some programs (especially optimizers, launchers, and games) may conflict with sensor drivers to identify them:

1. Load your phone in Safe Mode (hold the power button) → "Safe regime").
2. If the problem has disappeared, delete the apps one at a time, starting with the last ones installed.
3. Pay attention to the Clean Master, DU Battery Saver and similar utilities – they are often the culprits.

Turn off sync with Mi Account|Save photos on Google Photos or PC|Export contacts to VCF-file|Write down passwords from Wi-Fi (app "Wi-Fi passwords")|Check if you know the username/password from Mi Account-->

Update or rollback of firmware

If the problem has occurred after the MIUI update, try:

• 🔄 Update to the latest version – sometimes bugs are fixed in the following patches.
• 📉 Reverse to the previous firmware - to do this, download the desired version from the official Xiaomi website and run through Fastboot.

Attention: rolling back the firmware can cause the bootloop to be blocked if you don't follow the instructions. Always back up before you manipulate the software.

Hardware solutions

If the software doesn't work, you'll have to deal with hardware.

Screen cleaning and screening of protective film

Sometimes the cause of false presses is:

• 🧴 Screen pollution – fat, sweat, or dust can create parasitic contacts.
• 📱 Incorrectly pasted film - especially if it is with bubbles or peels off at the edges.
• 🧲 Magnetic cases - some accessories interfere with the work of the sensor.

Try it:

1. Carefully wipe the screen with a lilaless napkin with isopropyl alcohol (70%).
2. Take the protective film and test the phone without it.
3. Remove the cover and metal accessories (for example, a finger ring).

Checking the display plume

If the screen reacts to presses even when it is off, or the problem is localized in one zone (for example, only at the bottom), the plume is likely damaged. This is a typical malfunction for models with a movable display, such as the Redmi Note 10 Pro or the Redmi Note 10 Pro. POCO F3.

How to diagnose:

1. Carefully press the bottom of the screen (near the charging connector). If the presses are amplified, the plume will move away.
2. Light a flashlight under the screen - if a gap or curvature is visible, the plume is damaged.

Solution: replacement of the plume in the service center (cost) ~1500–3000 ₽). Self-repair is not recommended - there is a high risk of damage to the matrix.

💡

If spontaneous taps are accompanied by a flicker of the screen or stripes, the problem is almost certainly in the plume or matrix, in which case repair is inevitable.

Moisture intrusion and corrosion

Even if the phone hasn't sunk, condensation or high humidity can cause the contacts to oxidize.

• 💧 The problem gets worse in wet weather.
• 🔋 The phone overheats when charging.
• 📱 There are "dead zones" on the screen".

What to do:

1. Place your phone in a silica gel bag for 24 to 48 hours.
2. Use a cold-mode dryer to dry the body (do not direct air flow into the connectors!).
3. If corrosion is already there - it is necessary to disassemble and clean with alcohol (better in the service).

⚠️ Warning: Never use rice to dry your phone! Starch can get into connectors and make the problem worse. Silicagel is 10 times more efficient.

5. when you can not do without a service center

There are situations when self-repair is impossible or impractical:

If your Xiaomi is guaranteed, don’t try to repair it yourself – this will void warranty obligations. Contact the official Xiaomi service center with a check and a box. The average warranty repair period is 7-14 days.

For phones over 2 years old, it makes sense to compare the cost of repairs and new devices. 11T Pro's gonna cost you in ~10 000 ₽, whereas a used model can be bought for 18 000-22 000 ₽.

6 How to prevent recurrence of the problem

To minimize the risk of spontaneous pressing in the future, follow these guidelines:

• 🛡️ Use quality covers – they cushion the impacts and protect the plume from damage.
• 🔌 Avoid cheap chargers – they can cause voltage surges that are harmful to the screen.
• 🧼 Clean the screen regularly – dust and fat shorten the life of the sensor.
• 📲 Do not install optimizers and cleaners – they often conflict with system processes.
• 🔄 Update your firmware, but not immediately after release – wait 1-2 weeks in case of bugs.

If you drop your phone frequently, consider Corning Gorilla Glass Victus-protected models (like the Xiaomi 13 Pro or the X-rays). POCO F5 They are better at handling mechanical stresses.

It is also useful to enable the function of Locking the screen when falling (available on some models in Settings). → Screen. → It automatically turns off the sensor when it falls freely, preventing false pressing.

7. Alternative solutions for the time of repair

If you don’t have the option to give your phone to the service right now, use temporary measures:

• 🖱️ Connect the wireless mouse through USB-OTG — This will allow you to use the phone without touching the screen.
• 🎮 Activate voice control (Google Assistant or Mi) AI).
• 📱 Use gestures instead of touch buttons (includes in Settings) → Screen. → Navigation through the system).
• 🔒 Turn off the screen and control the device via Mi Remote (for basic features).

For models with IR-The port (e.g. Redmi Note 11) can be used temporarily by the TV remote as an alternative input method.

💡

If spontaneous taps prevent you from unlocking your phone, try connecting it to your PC and controlling it via Mi. PC Suite or adb. Command to unlock:

adb shell input keyevent 82

FAQ: Frequent questions about spontaneous clicks on Xiaomi