The situation where Xiaomi smartphone instead of the usual desktop endlessly shows the logo Mi or Redmi, and then reboots again, is familiar to many users. This state is called bootloop, and it can occur for a variety of reasons, from a failed system update to physical memory damage, you should not panic at this point, since in most cases the device is subject to software recovery without contacting the service center.
Before you start taking action, you need to understand the nature of the problem. Often users cause a failure by trying to install custom recoveries or modified firmware, but sometimes the culprit is a system file damaged by a sudden power outage. In 80% of cases, the bootloop is caused by a software failure of the file system or damage to the loader partition, not a physical failure of the motherboard. If your device just hangs, the first thing you do is try a forced reboot by holding the power button for 10-15 seconds.
The next steps depend on whether the gadget responds to commands and in what mode it gets stuck. We'll look at the full range of solutions, from secure data reset to complex computer flashing, and it's important to read each step carefully, because the wrong action can lead to complete loss of data or aggravate the situation.
Diagnostics of device status and entry into recovery modes
The first thing you need to do is determine what mode your Xiaomi is in.There are two main ways to log into service menus, and they are dramatically different in their features.Recovery mode is designed to reset settings and install updates, while Fastboot allows you to interact with the device at a low level through the computer.
To enter Recovery mode on the device turned off, press the up volume and power buttons simultaneously. Hold them until the logo appears, then release the power, but keep the volume down. If you see a menu with a few items in English or Chinese, you're lucky, you've got access to the recovery system. In Fastboot mode, the combination is different: the down buttons and power buttons are clamped until the image of a hare repairing an android appears on the screen.
⚠️ Warning: If you try to log in to Recovery, the phone goes back into a cyclical reboot, you may have damaged the recovery partition itself, and you can't do without connecting to your PC and using tools like the Mi Flash Tool.
The difference between these modes is critical. In Recovery, you can try to save data or reset, but you can't reflash the bootloader. Fastboot gives you full control of the device, but requires drivers and special software on the computer. If the phone responds to the connection to the PC with sound or vibration even when it's off (with the buttons pinched), the chances of successful recovery are extremely high.
📊 What mode does your phone respond to buttons?
Recovery (Menu with points)
Fastboot (Hare with Android)
Just vibration.
He's not responding.
Hard Reset Method with Recovery Mode
The most affordable way to fix a software failure is a complete data reset, known as Hard Reset or Vipe, which is effective if the bootloop is caused by a conflict of system files or errors after an update, but it is worth remembering that this process will permanently delete all user data: contacts, photos, apps and messages.
Once you're on the Recovery menu, you'll find two interfaces: the official (multi-item) or custom (e.g. TWRP). The official menu uses volume buttons and power buttons to navigate. You'll need to find Wipe Data. Some versions of MIUI may hide it in a submenu or otherwise, but the essence remains the same.
Once the reset point is selected, the system will ask for confirmation of the operation, often requiring a digital password or graphical key if installed. This is a security measure against data theft. Once confirmed, the cleanup process will begin, which will take from 30 seconds to several minutes, and when completed, the phone will suggest a reboot.
There's a nuance with Chinese firmware versions where the menu can be entirely in Chinese, so you can use the buttons. Usually, the reset button is second or third on top, and if you repeat the cycle after you reboot, it means that the problem is deeper, and simply deleting user data is not enough.
If the Recovery reset didn't work, you're left with "heavy artillery" -- a complete flashing of the device through your computer. USB-cable, Qualcomm or MediaTek drivers (depending on the processor), Mi Flash Tool utility and the.tgz firmware itself (not to be confused with zip for Recovery).
The process starts with putting your smartphone into Fastboot mode. Connect the device to your computer and open Windows Device Manager. Make sure that Android Bootloader Interface appears in Ports or Android Devices. If you see Unknown Device instead, you need to install or update the ADB and Fastboot drivers.
Launch the Mi Flash Tool on behalf of the administrator. Press the "Select" button and specify the path to the unpacked firmware folder. Importantly, there should be no Cyrillic characters or spaces on the way, otherwise the program will give an error. At the bottom of the window, select the firmware mode. For a clean start, choose clean all, which will delete all data and partitions.
flash_all.bat
Once you select the mode, press the Flash button. The process will take 200 to 600 seconds. At this time, it is strictly forbidden to turn off the cable or turn off the computer. If the progress bar has reached 100% and lights up green, the device will automatically restart. The first download after flashing can last up to 10 minutes - this is normal, the system configures files.
What if the Mi Flash Tool gives a "Miss matching image" error?This error means you're trying to flash firmware from another model or region, M2006J10G) It matches the code on the sticker under the battery or in the Fastboot. Using the wrong firmware can lead to a brick of the device.--> Specificity of Qualcomm processors and EDL Devices based on Qualcomm processors have a unique feature – emergency boot mode EDL (Emergency Download Mode: If the phone is so “brickled” that it does not respond to buttons or screens, but when connected to the PC, the connection sounds USB, It's probably in this mode. It'll appear as Qualcomm in Device Manager. HS-USB QDLoader 9008. Get to the EDL different ways. Many Xiaomi models have to disassemble the back cover and close special contacts (Test Points) on the motherboard when connecting the cable to the PC. ADB-team
adb reboot edl, but they only work if the phone responds to commands. EDL allows you to flash the device even with a completely damaged bootloader. However, starting with certain versions of MIUI, you need a Xiaomi authorized account with engineer rights to be able to run through EDL to firmware. Regular users may experience an authorization error, and in such cases you have to contact service centers or use paid remote firmware services. Fastboot Mode setting EDL Mode (9008) Recovery Mode Appearance Hare with Android Black Screen Menu with Data Access No Partially No (TWRP) Destroy button / button command Efficiency High Maximum Average Problems after system upgrade and customization A frequent cause of bootloop is an attempt to install global firmware on the Chinese version of the device (and vice versa) or install custom recaveri TWRP. The architecture of the memory partitions may vary from region to region, such as trying to flash Global. ROM on CN-A version without unlocked bootloader and the correct conversion procedure is guaranteed to lead to a reboot cycle. If you installed kernel modifications, Magisk modules or changed system files, they can cause conflict. In this case, entering safe mode is often impossible due to the bootloops. The only solution is to return to factory stock firmware through Fastboot, as described above. TWRP, They allow you to back up before you experiment, and if you do, it takes a couple of minutes to recover through Restore, and it's also worth mentioning the memory overload problem. If the internal memory of the smartphone was crammed to the end, the system could not correctly write the update files when restarted, resulting in broken sectors or a corrupt file table. TWRP (Format Data and Yes often help solve a problem if it has not developed into physical degradation of the drive. 💡Always make a full backup of important data before any firmware manipulation, unlocking the bootloader or installing custom Recovery. Hardware malfunctions and when to carry to the service Do not forget that software methods are powerless against physical failures. EDL The mode is that the phone keeps going to the bootloop, most likely the problem is the hardware. The most common culprits are the failure of Flash memory (eMMC or eMMC). UFS) Memory degradation is a natural process, and after years of actively writing and overwriting, the memory cells wear out, and the phone starts to lose the system files, even if they've just been written. Symptoms may also be frequent hanging, slow operation and spontaneous reboot until complete failure. ⚠️ Note: If the phone fell, fell into the water or was subjected to heavy heat, the bootloop may be the result of the departure of the contacts of the plumes or the oxidation of the board. In such cases, self-repair without soldering equipment and a microscope is impossible, and the cause may be a faulty battery. If the battery is not holding the voltage at the time of start of the processor, the phone will turn off or reboot on the logo. You can check this by connecting the device to a powerful charger for a long time, or temporarily replacing the battery. ☑️ Phone is warming up in the off state when charging Computer does not see the device even in Fastboot Artifacts appear on the screen before turning off The smell of burning or bloating the Bootloop battery after falling or getting water: 0 / 5 Frequently asked questions (FAQ) Will the warranty drop if I tried to remove the bootloop myself? Yes, if you opened the case in the process (to enter the building). EDL), violated seals or flashed the device with unofficial software, the service center may refuse warranty repair. However, if you only used the regular Recovery menu with buttons, there will be no external signs of interference, and formally the warranty should be preserved, although it can be difficult to prove the absence of third-party software. Can you save photos and contacts without resetting data? In bootloop mode, the chances are minimal. If the phone doesn't boot into the system, you can't access the file system. The only chance is if you've had sync enabled with Mi Cloud or Google Photos. ADB pull) 99% of the time, because Android's security system blocks access to data on an unloaded device? This is often due to interrupted download of the update file (bad Internet) or lack of free space to unpack the archive. There may also be conflicts between the old file system and new system requirements. In such cases, only complete flashing through the computer helps. How long can the first download last after flashing? The normal first download time (when the Mi logo appears and the progress bar) is from 3 to 10 minutes. If the phone hangs on the logo for more than 15-20 minutes, the firmware process may have been error-free or an incompatible version of the software is selected. In this case, the Flash procedure should be repeated, you choose all clean and all the region.