Xiaomi TV is not updated: 12 reasons and what to do in 2026

Update firmware on Xiaomi Mi TVs TV or Redmi Smart TV — It's a standard procedure that usually goes unnoticed by the user, but what if the system stubbornly refuses to install new versions of the software? Hanging up during the check updates, errors such as “No connection to the server” or endless download – these problems are faced by owners of devices of different generations, from Mi to the Internet. TV 4A before the flagship Xiaomi TV Q2 2026.

In this article, we’ll look at all the possible reasons why Xiaomi TVs aren’t updated, from trivial network failures to hardware malfunctions. You’ll get step-by-step instructions for each case, including manual firmware through the phone. USB, Resetting to factory settings and diagnosing iron components, with particular attention to the new Xiaomi 2026 restrictions that block updates on devices with unofficial firmware or modified regional settings.

If your TV is stuck on the logo after a failed update or completely stopped turning on – at the end of the article there is a section with emergency recovery methods that will help bring the device back to life without contacting the service center.

1. Checking the Internet connection - the first step of diagnosis

More than 60% of update issues on Xiaomi TVs are due to an unstable internet connection, even if other devices on the network are working normally, TV can block the loading of firmware due to the specific settings of the router or provider.

What you need to check first:

• 🔌 Connection type: Xiaomi TVs are most often upgraded over Wi-Fi, but for large updates (over 1 GB) it is recommended to use an Ethernet cable. LAN on TV.
• 📶 Network Speed: Run a speed test on your TV (Settings) → Network → Speed test) Updates require at least 5 Mbps of stable speed.
• 🔒 Lockdown DNS: Some providers (such as Rostelecom or Beeline) may restrict access to Xiaomi servers. DNS 8.8.8.8 (Google) or 1.1.1.1 (Cloudflare).
• 🕒 Synchronization time: if the date and time of the TV If you're lost, Xiaomi's server will refuse to connect. → System system → Date and time.

If you use Wi-Fi, make sure the router is running in mode. 802.11n/ac (5 GHz) Old Xiaomi models (e.g. Mi Mi) TV 3S) They may not support modern Wi-Fi standards. 6, Also, disable the Smart Routing feature in the router settings, which sometimes conflicts with the Xiaomi update protocol.

⚠️ Note: If the TV is connected via PPPoE (direct connection to the provider without a router), the updates may be blocked due to dual authentication. TV router or set up DMZ for IP-address.

Xiaomi server errors: how to get around the restrictions

Xiaomi periodically updates its server infrastructure, which can lead to temporary disruptions. In 2026, the company tightened its firmware distribution policy: devices with unofficial regions (for example, re-flashed from the Chinese version to the global version) may receive updates with a delay or not receive them at all.

Signs of problems on the side of Xiaomi:

• 🔄 “Updates are not available” message when manually checked.
• ⏳ Infinite download at the “Update Check” stage (more than 10 minutes).
• 🚫 Error "Impossible to connect to the server" (code 10008 or 20004).

Decisions:

1. Change of firmware region: If your TV was originally bought for the Chinese market (CN-version), but you are using it in Russia, try to change the region through Settings → On TV. → Region: Select Russia or Global and restart your device.
2. Use of the VPN: Connect the TV to VPN servers in Hong Kong or Singapore (for example, via a router with a configured VPN). This will help to bypass regional locks.
3. Manual Firmware Download: Download the latest version of the software for your model from the official Xiaomi Support website and install it through the official Xiaomi Support website USB.

If the 20004 error appears on Xiaomi TVs TV A Pro or Redmi Smart Fire TV, This may indicate a conflict with Amazon services, which requires a factory reset, disabling all accounts before upgrading.

3. Memory Lack: Why the Update Is Not Installed

Xiaomi TV firmware is getting bigger every year. If the device has less than 1.5 GB of free space, the system may refuse to install an update even if the download was successful. TV 4A 32GB), where most of the memory is occupied by pre-installed applications.

How to make room:

• 🗑️ Cache Removal: Go to Settings → Annexes → App management and clear cache for all unnecessary programs (especially Google Play Services and Mi Home).
• 🎬 Transfer media: Photos, videos and music to an external drive (a flash drive or hard drive).
• 🔄 Application Data Reset: For system applications (e.g, TV Manager: Reset the data – it will free up to 500 MB.
• 🚫 Removal of unnecessary APK: Through Settings. → Security → Find and delete files with the.apk extension left over after installing applications.

If there is critically little free space, and you do not want to delete anything, you can use an external drive to install the update:

1. Format the flash drive in FAT32.
2. Download the firmware (.zip) and place it in the drive’s root directory.
3. Connect the flash drive to the TV and run the update via Settings → About the device → Updating the system → Update through USB.

⚠️ Attention: On Xiaomi TVs TV P1 and newer to install firmware with USB A signed file from Xiaomi is required. Unofficial builds can lead to locking the device!

System failures: from reboot to reset

If the Xiaomi TV freezes during the Preparation for Update stage or if it gives an error “Failed to install the update” (code 10012), this indicates a software failure, in most cases, a forced reboot or factory reset helps.

Soft reboot (without data loss):

1. On the remote, hold the power button for 10-15 seconds until the TV turns off.
2. Turn off the power outlet for 1 minute.
3. Turn it on. TV and try again to update.

Hard reset (with loss of data):

1. Go to Settings → About TV → Reset settings.
2. Choose to erase all data and confirm the action.
3. After the reboot, reset the TV and check for updates.

If the reset didn’t help, try disaster recovery via Fastboot (power users only):

fastboot flash recovery recovery.img


fastboot flash boot boot.img




fastboot reboot

Files. recovery.img and boot.img You can get it from the official firmware for your model.

5.Iron problems: when the hardware is to blame

If all software methods have been tried, but the Xiaomi TV is still not updated, the problem may lie in hardware malfunctions.

• 🔋 Faulty power supply: when voltage drawdowns, the TV may turn off during the upgrade, leading to a failure.
• 💾 Damaged flash memory: If memory cells are worn out, the system cannot write new firmware data.
• 🔌 Oxidized contacts USB/HDMI: This prevents the correct operation of ports through which the update can be installed.
• 🔥 Overheating of the processor: at high temperature, the system automatically interrupts the installation of the update.

How to diagnose hardware problems:

1. Power supply check: Connect the TV to another power source (e.g. via a power supply) UPS). If the update goes through, it's the power supply block to blame.
2. Memory test: Run the diagnosis through the service menu (on the remote, press Menu). → Settings → All Settings → Device Preferences → If there are read/write errors, you need to replace the flash drive.
3. Port inspection: Check out USB and HDMI If you're not aware of oxidation or damage, clean your contacts with alcohol.

If you want a Xiaomi Mi TV TV 5 Pro or later is not updated and at the same time restarts or turns off after 5-10 minutes of operation, this may indicate a malfunction of the cooling system.

⚠️ Attention: On Xiaomi TVs TV Q2 2023/2026 MediaTek-based MT9638 If there is a hardware failure, Secure Boot can be activated, blocking the firmware installation. EDL-The service (only in the service center!).

6 Manual update through USB: step-by-step

If the automatic methods fail, you have to install the firmware manually, which is suitable for all Xiaomi models, including the Redmi Smart. TV X and Xiaomi TV Important: Wrong firmware can turn a TV into a brick»!

Step-by-step:

1. Download the firmware: Go to Xiaomi's official website. Enter the exact model of the TV (indicated on the sticker at the back). Download the latest.zip file (don't unpack!).
2. Prepare the flash drive: format it into FAT32 (not exFAT or NTFS!). Place the firmware file in the root directory (not in the folders!). Rename the file to update.zip (necessarily!).

Install the update

• Put the flash drive in. USB 2.0 port (usually black).
• Go to Settings. → On TV. → Updating the system → Update through USB.
• Confirm installation and wait until completion (do not turn off) TV!).

If the TV has been on the logo for more than 10 minutes after the update:

• Pull out the flash drive.
• Hold the Power button on the remote for 20 seconds to force reboot.
• If the problem repeats, scroll the device again with a full reset (Wipe Data).

💡

Before manual update, disable all peripherals (sound panels, game consoles, TV-consoles, except for the remote and the flash drive, which will eliminate driver conflicts.

7. Update through ADB: for advanced users

If standard methods do not work, and the TV is still turned on, you can try installing the firmware through the ADB (Android Debug Bridge. This method is suitable for Android models TV, like the Xiaomi Mi TV Stick or Xiaomi TV Q1.

What you need:

• A computer with ADB and Fastboot installed.
• Cable USB-A — USB-A (plug-in TV PC).
• The firmware file is in.zip format.

Instructions:

1. Turn on the debugging. USB on TV: Settings → On TV. → Android Version (click 7 times) Settings → Additionally. → Developer parameters → Debugging by USB
2. Connect. TV to the PC and check the connection: adb devices (should display the serial number of the device).
3. Copy the firmware on the TV: adb push update.zip /sdcard/
4. Install the update: adb shell su recovery --update_package=/sdcard/update.zip

If the su command is not working, then the TV is not rooted.

adb sideload update.zip

⚠️ Attention: On TVs with MIUI TV 3.0 and later (2023–2026) debugging USB It can be blocked by default. It requires authorization through a Xiaomi account to activate it.

8.If nothing helps: contact the service

If all of these methods have failed and the TV is still not updated (or turned on at all), it is likely that the problem is hardware in nature, in which case it is recommended to contact an authorized Xiaomi service center.

Signs that without the service can not do:

• 🔴 The TV does not respond to the power button (no indication).
• 🔄 Loading (Infinite Bootloop).
• 💥 The appearance of artifacts on the screen or the absence of an image.
• 🔌 The TV is turned off immediately after connecting to the network.

What to do before visiting the service:

1. Take a picture of the serial number (on the back sticker) and the TV model.
2. Write down the errors that appear on the screen (if any).
3. Check if the warranty is saved (for Russia, check the Xiaomi Russia website).

Cost of repair in the service:

If the TV is warranty, repairs will be free, but note: the warranty does not apply to devices with root rights, unofficial firmware or mechanical damage.

💡

Before visiting the service, perform a full reset (Wipe Data) - this will increase the chances of successful firmware recovery without replacing components.

FAQ: Frequent questions about Xiaomi update TV