Fitness tracker owners often face a situation where the device discharges at the most inopportune moment, requiring an immediate connection to the power source.The question of how much the Xiaomi Mi Band 4 is charging becomes critical to planning for the use of the gadget.The standard battery capacity recovery time varies, but usually fits into specific time frames prescribed by the manufacturer.
The rate of filling the battery depends not only on the specifications of the bracelet itself, but also on the state of the charging cable, power supply and ambient temperature. Understanding these factors will help you avoid panic if the indicator flashes slower than you are used to. In this article, we will discuss in detail all aspects of charging, typical problems and ways to solve them.
Many users mistakenly believe that any USB-The port is suitable for fast charging, but current strength is crucial, and the use of inappropriate adapters can not only increase latency, but also negatively affect the health of lithium polymer batteries in the long run. Let’s figure out how to properly use your tracker.
Standard charging time and specifications
According to official documentation from Xiaomi, the full charging cycle of the fitness bracelet Mi Band 4 takes an average of 1 to 2 hours. USB-If you use more powerful adapters, the time may be reduced slightly, as the power controller inside the device limits the incoming current for safety.
The built-in battery capacity is 135 mAh, which is the best indicator for a compact device, and this capacity allows the tracker to operate in active mode for up to 20 days without recharging, depending on the notification settings and the frequency of heart rate measurement. It is important to understand that the last percentage of charge can be gained longer due to the balancing algorithms of the cells.
⚠️ Note: If your bracelet is more charged 3-4 hours, this is a clear sign of faulty charging cable, oxidation of contacts or battery degradation.
The current discharge level also affects the speed of the process. Deep discharge may require a preliminary "swing" of the battery, when the charging indicator may not light up immediately after connection, in which case the device must be left on charging for at least 15-20 minutes before the screen responds to touch.
💡
Use a 1A (1000mA) adapter for optimal charging speed. Powerful units from smartphones (2A and higher) won’t speed up the process significantly, but can heat the device more.
Factors affecting the rate of energy recovery
You don't expect to have the same charging speed in any environment. There are a number of variables that directly affect how fast the indicator will go 100%. First of all, the quality of the connections on the back of the tracker and the charging dock. Even a microscopic layer of sweat or dust can increase resistance and slow down the process.
The ambient temperature plays an important role in the chemistry of lithium batteries: At temperatures too low or too high, the power controller artificially limits the current charge to prevent battery damage, and a room temperature of 10 to 30 degrees Celsius is considered ideal.
- 🔌 Source power: Charging from a computer (USB 2.0 will occur more slowly (about 2 hours) than from a network adapter (about 1 hour).
- 🌡️ Temperature: In the cold, the charging speed drops, and in the extreme heat, the process can be completely stopped by the protection system.
- 🔋 Battery condition: Older batteries with more recharge cycles can charge unevenly and keep the last percentages longer.
If you are constantly monitoring your pulse during charging or if you are actively searching for a smartphone through the Mi Fit app (now Zepp Life), some of the energy will be consumed immediately, which will visually slow down the growth of percentages on the screen.
How to know if the charging is going right
The visual indication on Xiaomi Mi Band 4 is quite simple, but it's informative. Right after you plug the cable into the port and you put the tracker in the dock, the screen should light up. You'll see the lightning icon and the current percentage of charge. If the screen doesn't respond, try to wipe the contacts or move the bracelet at the dock station.
It's normal to get a higher charge in the first 30 minutes and then slowly slow down, and that's the standard CC/CV algorithm used in modern electronics to extend battery life, and you shouldn't be afraid if you start charging more slowly after 80 percent.
You can also check status through a smartphone app. The Zepp Life interface displays the exact percentage of charge that is updated after synchronization. If you have one percent attached and another percent on your wristband, manually sync the device list down.
Comparison of charging time with other models
For context, it’s useful to compare the fourth model with its predecessors and competitors. Xiaomi has traditionally used similar batteries in its trackers, so the difference in charging time is often due to software optimizations or capacity.
Below is a table showing the comparative characteristics of charging time and autonomy of popular fitness trackers:
| Model of the device | Battery capacity (mAh) | Full charge time. | Autonomy (days) |
|---|---|---|---|
| Mi Band 3 | 110 | ~1.5 hours | 20 |
| Mi Band 4 | 135 | ~1.5 - 2 hours | 20 |
| Mi Band 5 | 125 | ~2 hours | 14 |
| Honor Band 5 | 100 | ~1.5 hours | 10 |
As the data shows, the Mi Band 4 has one of the best combinations of capacity and charging speed in its class.The capacity increase over the third model did not lead to a critical increase in latency, which is a credit to an efficient power controller.
💡
Despite the similar charging time with competitors, the Mi Band 4 benefits from software optimization, allowing you to keep the charge longer when used actively. AMOLED-screen.
Typical problems and methods of their elimination
Sometimes users are faced with a situation where the bracelet stops charging or the process is extremely slow. Most often the problem lies in the oxidation of the gilded contacts. The sweat that hits the back panel dries out and forms a conductive or, conversely, insulating film that interferes with contact.
To solve this problem, you need to gently wipe the contacts on the bracelet and on the charger with a dry soft cloth or cotton swab slightly soaked in alcohol. Let the surface dry completely before reconnecting. Also check if the tracker is sitting tight in the docking station.
⚠️ Warning: Never use metal objects (needles, scissors) to clean the contacts so as not to damage the protective coating and cause a short circuit.
If mechanical cleaning didn't work, it could be software. In rare cases, the charging controller freezes. Try rebooting the bracelet through the settings menu or plugging it into another one. USB-If the light flashes red and the device doesn't turn on, it's possible that the battery has gone into a deep discharge and requires a powerful shock within minutes.
☑️ Diagnostics of charging problems
Recommendations for extending battery life
To keep your Xiaomi Mi Band 4 long and charged, it is important to follow the rules of operation of lithium polymer batteries. Do not discharge the device to zero regularly. It is optimal to put the tracker on charge when the energy level drops to 15-20%.
Keeping a fully discharged device for long periods of time is detrimental to battery chemistry. If you plan to keep the bracelet out for a long time, charge it to about 60 percent and turn it off. Periodically, every few months, check the charge level and recharge it.
- 🚫 Avoid overheating: Do not leave the tracker on charging in direct sunlight or on a hot surface.
- 💧 Moisture protection: Although the device has moisture protection, charging a wet bracelet is strictly prohibited - this will lead to corrosion of contacts.
- 🔌 Cable quality: Use only original or certified cables, as cheap counterparts may not have adequate protection against voltage surges.
These simple rules will keep the battery close to the factory even after a year of active use, remember that the battery life is limited by the number of cycles, and proper operation helps to maximize it.