How many atmospheres should be in the tires of the Xiaomi scooter: pressure table for all models

Xiaomi’s electric scooters have become an integral part of urban mobility, but their reliability is directly dependent on the condition of the wheels, and one of the key parameters that many owners overlook is tire pressure. Incorrectly pumped wheels not only reduce ride comfort, but also increase the risk of punctures, accelerate tread wear and even affect battery power. In this article, we will analyze how much pressure should be in the tires of the Xiaomi scooter for each model – from budget to budget. M365 The Electric Scooter 4 Pro will be available and will be able to measure and adjust it correctly.

Have you ever wondered why the same scooter behaves differently between owners? The reason is often because of pressure: over-pumped tires make driving tough and prone to aquaplaning on wet roads, and under-performed tires increase rolling resistance, making the engine work for wear. The manufacturer gives recommended values, but they can vary depending on the weight of the rider, the type of coverage and even the air temperature. Next is a detailed guide with tables, tips and life hacks from experienced users.

Xiaomi’s official tire pressure recommendations

Xiaomi always gives basic pressures in its scooters instructions to ensure safe and efficient operation, which are calculated for the average user weighing 70–80 kg when driving on asphalt, but it is important to understand that they are advisory and can be adjusted.

For most models, the range is 2.0-2.5 atmospheres (or 29-36). PSI But there are nuances to the American measurement system:

• 🛴 Xiaomi M365 and M365 Pro: 2.2-2.5 atm These scooters are equipped with 8.5-inch wheels with cameras, where the pressure is critical to prevent a “snake bite” (puncture of the camera with a rim when hitting an obstacle).
• 🚀 Xiaomi Pro 2 and 1S: 2.0-2.3 atm. It uses wider tires, which allows you to slightly reduce the pressure for better grip.
• 💎 Xiaomi Electric Scooter 3/4/4 Pro: 2.3–2.6 Models with tubeless tires require higher pressure to maintain the shape of the tire.

Where do you look for the exact data for your model?

• 📄 On the sticker on the frame of the scooter (near the serial number).
• 📱 In the electronic instructions in the Mi Home application (section "User Guide").
• 🌐 On the official website of Xiaomi in the product card (the tab "Specifications").

⚠️ Note: If you can not find recommendations for your model, focus on the average value of 2.2-2.4 atm. Exceeding pressure above 2.8 atm is fraught with rupture of the chamber, and below 1.8 atm - deformation of the tire and the risk of its jumping from the rim.

Pressure table for popular Xiaomi models

Below is a summary table with recommended pressure values for the most common Xiaomi scooters, based on official sources and tests by independent experts.

Note that for tubeless models, the upper limit of pressure is higher, due to the design of the tire, which keeps the shape due to internal pressure, rather than the camera frame, and the table does not include modifications with reinforced tires (for example, Xiaomi). M365 Honeycomb tires, where pressure can reach 3.0 atm.

How the weight of a rider affects the pressure in tires

Xiaomi’s official guidelines are for users up to 100kg, but if your weight goes beyond that, the tire pressure needs to be adjusted.

• 👶 Weight up to 60 kg: reduce pressure by 0.2-0.3 atm from the recommended. This will improve grip and reduce stiffness.
• 🏋️ Weight 100-120 kg: increase the pressure by 0.3-0.5 atm. This will prevent the tyre from bending and protect the rim from impact.
• 🏋️‍♂️ Weight over 120 kg: Consider installing reinforced tires or reducing load (e.g. avoiding sharp accelerations).

Why does it matter? When you're under pressure, the tire deforms, which causes:

• 🔥 Overheating of the tire and the risk of its destruction.
• 🔋 Increased energy consumption (the battery goes down faster by 10-15%).
• 🚨 Loss of control at high speed or with sharp braking.

⚠️ Note: If you often drive with a passenger or cargo, tire pressure should be at the upper end of the recommended range. M365 This is 2.5 atm, even if you normally pump up to 2.3 atm.

💡

Use free online scooter pressure calculators (e.g. ScooterHacking) that take into account weight, tire type and driving style, giving personalized recommendations.

How to measure the pressure in the tires of the scooter

You need to check the pressure in the tires of the Xiaomi scooter at least once every two weeks, and before long trips, you need a pressure gauge, any one will do: mechanical, electronic or even built-in pump. The main thing is that it maintains measurement in atmospheres (atm) or PSI.

Step-by-step:

1. 🛠️ Remove the cap from the nuppel (it protects the valve from dirt).
2. 🔧 Press the pressure gauge against the nipple and hold for 1-2 seconds until the arrow or numbers on the screen stabilize.
3. 📝 Write down the readings. If they're below normal, pump up the tire, if they're higher, blow the air with a pin of a nipple.
4. 🔄 Repeat the procedure for the second wheel.

A few important nuances:

• 🌡️ Measure the pressure in cold tires (if the scooter stood for at least 2-3 hours). When driving, the tires heat up, and the pressure increases by 0.2-0.4 atm.
• 🕒 It is better to check the pressure in the morning when the air temperature is minimal.
• 🚫 Do not use pressure gauges from car compressors at gas stations – they often show inaccurate values for small volumes (as in scooters tires).

How to pump up the tires of the Xiaomi scooter: a step-by-step guide

If the tire pressure is below normal, you need to pump them up, and any pump, whether it's a foot, hand or electric pump (with a Schrader nipple adapter, which is used in Xiaomi scooters), will do it right:

Step 1: Preparation

• 🧹 Clean the nipple of dirt with a cloth or a napkin. Getting sand or dust into the valve can lead to clogging.
• 🔌 If you use an electric pump, make sure it maintains low pressure (many car compressors don't pump below 0.5 atm).

Step 2. Connect the pump:

• 🔗 Put the pump fitting tightly on the nipple. If you hear hissing, the connection is leaky, correct it.
• 📉 Some pumps have a pressure relief button – make sure it is pressed off.

Step 3. Pumping:

• 💨 Swing in short intervals of 5-10 seconds, periodically checking the pressure with a pressure gauge.
• 🎯 As soon as the value reaches 0.1-0.2 atm below the target, stop pumping - when the pump is disconnected, part of the air is blown off.

Step 4. Completion:

• 🔌 Remove the pump connection quickly to minimize air loss.
• 🧭 Check the pressure with a pressure gauge and, if necessary, add air.
• 🚪 Cover the nipple with your cap.

⚠️ Warning: Never pump Xiaomi scooter tires above 3.0 atm, even if you think they are "soft" This can cause the camera to explode or the tubeless tire to rupture!

Frequent mistakes in tire pumping and how to avoid them

Even experienced Xiaomi scooter owners sometimes make mistakes that lead to premature tire wear or crashes.

1. Ignoring ambient temperature

Tyre pressure changes with temperature fluctuations: every 10 times°The difference is about 0.1 atm, for example, if you've inflated your tires to 2.3 atm at a time. +20°C, then −10°C pressure drops to ~2.0 atm Solution: Check your pressure in the conditions you normally drive, or adjust it for the season.

2. Use of an inappropriate pump

Many people try to pump scooter tires with a car compressor, but most of them:

• 🚗 They cannot accurately dosage small volumes of air.
• 💥 They can exceed the pressure if you do not monitor the pressure gauge.

The best option is a bicycle pump with a pressure gauge or a specialized pump for scooters (for example, Xiaomi Portable Electric Air Pump).

3. Neglect of nipple testing

Over time, the nipple valve (Schrader) can clog or damage, leading to slow air leakage.

• 💨 Tires are lowered in 1-2 days without visible punctures.
• 🔊 Hear hissing when checking the pressure.

Solution: Wash the nipple with alcohol or replace it (worth it) ~100-200 rubles).

💡

The most dangerous mistake is running flat tires, which not only damages the tires, but can also lead to loss of control at speeds over 25 km / h.

How the type of coating affects the choice of pressure

The pressure in the tires of the Xiaomi scooter depends not only on the model and weight of the rider, but also on what surface you drive.

1.Asphalt and flat surface

For urban roads with smooth asphalt or tiles, the upper value of the recommended range is optimal (for example, 2.5 atm for the road). M365). That will ensure:

• ⚡ Minimum rolling resistance (large range).
• 🛡️ Protection of the rim from blows against small stones.

2. Soil, gravel, uneven covering

On off-road or forest paths, it is better to reduce the pressure by 0.2-0.4 atm.

• 🏔️ Improves depreciation and clutch.
• 🚫 Reduces the risk of puncture with sharp objects (the tire will "flow around" them).

But do not overdo it: pressure below 1.8 atm will lead to the "chewing" of the tire rim.

3. Wet asphalt or snow

In rainy weather or winter, it is recommended to:

• ☔ Reduce pressure by 0.1–0.2 atm to increase contact spots.
• ❄️ Use tires with aggressive tread (for example, Xiaomi Winter Tires).

This will help avoid aquaplaning and improve braking.

💡

If you often drive on different coatings, buy a portable pump with a pressure gauge (for example, Xiaomi Mi Portable Electric Air Compressor), which fits into a backpack and allows you to quickly adjust the pressure on the go.

FAQ: Answers to Frequent Questions About Tyre Pressure in Xiaomi