How to add soap to the touch soap Xiaomi: instructions + tips for care

Xiaomi touch soaps have become a popular bathroom accessory thanks to a combination of technology and practicality, which automatically deliver a dose of liquid soap or gel when you put your hand up, saving consumption and maintaining hygiene. However, many users are faced with the question: how to put soap in the touch soap soap soap soap so that you do not damage the mechanism and keep it working?

In this article, we will look at all the nuances, from choosing the right detergent to step-by-step instructions for refueling, what mistakes owners most often make (such as using thick gels or improper assembly), and how to avoid them, and we will provide care recommendations that will prolong the life of the device for years.

Important: the soap dopping procedure in Xiaomi Soocare S1, Mijia Smart Soap Dispenser and similar models has general principles, but may differ in detail. If your soapbox is equipped with a UV lamp for disinfection or battery, pay attention to additional rules of use.

What Soap Is Right For Xiaomi Touch Soap

Not every detergent is compatible with automatic dispensers, but the main criterion is consistency: too thick gels or soaps with abrasive particles can clog the pump or sensor.

• 🧼 Liquid soap marked "for dispensers" (e.g. Dove, Palmolive, Ecover) has a balanced viscosity and does not contain lumps.
• 🧴 Antibacterial gels without alcohol (alcohol solutions can damage plastic parts) will work Safeguard or Lifebuoy in liquid form.
• 🌿 Plant-based eco-friendly products (e.g. BioMio or Frosch) if they do not contain oils that may oxidize and damage the mechanism.

What to avoid:

• ❌ Thick cream soaps or scrubs - they clog the tube and pump.
• ❌ Fragments with perfumes based on essential oils - can leave a sticky sediment.
• ❌ Homemade soap (e.g. diluted hard) – unstable consistency will lead to breakage.

Tip: Before filling a new product, check its viscosity. Drop a little on your hand, if the soap drains freely (like water), it fits. If there's a lump left, you better not use it.

Preparation of soap boxes for doling: disassembly and washing

Before pouring new soap, the device should be thoroughly washed, especially if you change the type of product or fill the soapbox for the first time after buying.

1. Turn off the power. If the soap is powered by batteries or batteries, remove the batteries. For USB-cabled models (e.g. Xiaomi Mijia Smart Soap Dispenser Pro), uncord.
2. Remove the top cover. It's usually mounted on the latches -- gently press the side and pull up. In some models, the lid is unscrewed counterclockwise.
3. Remove the soap tank. In most soap tanks, it's transparent or semi-transparent, with minimum/maximum level labels.
4. Wash all the details. Use warm water (not hot!) and a soft sponge. Pay special attention: 🔹 Soap supply tube - clean it with a needleless syringe, pouring water. 🔹 Sensor – wipe it with a dry wipe, do not use alcohol! 🔹 Pump – if deposits are noticeable, soak the part in water with vinegar (1:1) for 10 minutes.

Shut down the power.

Remove the top cover

Remove the soap tank

Wash all the details with warm water

Dry components before assembly-->

Never immerse an electronic unit (with a sensor and a pump) in water completely. Just wipe it with a wet wipe.

Step-by-step: how to add soap to the touch soap box

When the soap is washed and dried, you can start filling. Follow this instruction to avoid leaks and breakages:

1. Set the tank in place. Make sure it fits tightly to the base, otherwise the soap will leak past the pump.
2. Pour the soap to the "MAX" label. Don't overflow the tank! In Xiaomi Soocare S1 models, the maximum volume is 300 ml. Use the funnel or bottle nose to avoid the spills.
3. Close the lid. Make sure all latches are locked. In some soapboxes, the lid locks before the click.
4. Turn on the power. For batteries, put them in polarity. USB-Models: Connect the cable to the outlet.
5. Test the work. Put your hand up to the sensor, a soap (usually 1 to 1.5 ml) should stand out. If the dose is too small or too high, adjust the settings (if the model supports calibration).

If no soap is served after filling:

• 🔋 Check the batteries/charge of the battery.
• 🔄 Reboot the device (remove and insert batteries or turn off) USB 10 seconds).
• 💧 Make sure the soap is not too thick – dilute it with water (1:1) if necessary.

💡

If the soapbox gives out soap jerks or interruptions, there is likely air in the tube. Tilt the device at a 45° angle and press the dispenser manually (if the model supports mechanical pressing) to blow air.

Frequent mistakes with soap and how to avoid them

Even experienced users sometimes make mistakes that lead to breakage or deterioration of the soapbox, and here are the most common ones:

⚠️ If you pour abrasive particles (such as a scrub) into the soapbox, wash the device immediately, the pump and the sensor will be damaged by sand or salt, and the warranty does not apply.

• 🚫 Soap overflow, if you pour it above the marker "MAX", When heated (for example, in a hot water bath), it can leak out and damage the electronic unit.
• 🚫 Using high pH products (such as in some household soaps) corrodes plastic and rubber seals. Optimal pH is 5.5-7.0.
• 🚫 If the tank is crooked, the soap will flow past the pump and the sensor will not work. Always check the density of the parts.
• 🚫 Ignoring flushing. Residues of old soap mix with new soap to form lumps. Rinse the soapbox at least once in 2-3 gas stations.

How to understand that the soap requires urgent cleaning:

• 🔴 Soap is served with delay or unevenly.
• 🔴 There were sticky divorces on the body.
• 🔴 Sensor goes off again.

Care for the touch soap: extending the service life

To make Xiaomi’s soap last longer, follow these guidelines:

• 🧽 Clean the tank and tube every 2-3 weeks, even if everything looks clean. Use vinegar solution (1 tbsp. per glass of water) to remove lime plaque.
• 🔋 Power: If the soap is powered by batteries, remove them for long periods of downtime (e.g., during vacation). USB-Use the original cable – cheap analogues can damage the controller.
• 🌡️ Storage conditions: Do not place the soap box near heat sources (such as over a towel warmer) or in direct sunlight. Optimum temperature is 10-35°C.
• 🛠️ Prevention: Once a month, check the sensor, wipe it with a dry wipe and test the response on your hand.

For models with a UV lamp (for example, Xiaomi Youpin Smart Dispenser):

• 💡 Turn on disinfection no more than 1 time a day - this will prolong the life of the lamp.
• 👁️ Don’t look at a working UV lamp – it’s bad for your eyesight.

💡

Use only original parts (e.g. rubber seals) when replacing, and non-original parts may not be leaky, leading to leaks.

Alternative ways of refueling: life hacks and non-standard solutions

If the standard method of soap dousing does not suit you, you can use alternative options:

• 🔄 Dilute the thick soap. If your favorite is too viscous, dilute it with distilled water (1:1). Stir to a uniform consistency and pour it into a soap box. Important: don't use tap water - chlorine and salts can settle on parts.
• 🧴 Use of container-inlay. For models with a large tank (e.g. Xiaomi Soocare) S1) You can buy silicone liners that simplify refueling and protect against leaks.
• 🔋 Refueling without power out. In some soapboxes (for example, Mijia Smart Soap Dispenser), the tank can be removed without turning off the device.

For DIY lovers:

• 🛠️ A homemade adapter. If you have multiple soaps, you can make a silicone tube adapter to fill them up from one large container.
• 🎨 Decorative sticker: To avoid confusing soaps (for example, soap and shampoo), use water-resistant stickers. Don't glue the sensor!

⚠️ Attention! If you're experimenting with homemade solutions (such as a mixture of soap and essential oils), first test them for plastic compatibility. Apply the drop on the inside of the lid and leave it for a day - if the material has not deformed, the tool can be used.

Comparison of touch soaps Xiaomi: which to choose for refueling

If you haven’t bought a touchscreen soap yet or are thinking about replacing the old model, note the key differences between Xiaomi devices:

Which model should I choose?

• 🔋 If you are interested in autonomy – Soocare S1 (The battery lasts for 6-8 months).
• 🔌 For permanent use in the bathroom suitable Mijia Smart Soap Dispenser with USB-feeding.
• 🦠 If hygiene comes first – Youpin Smart Dispenser with a UV lamp and a large tank.

FAQ: Answers to Frequent Questions