Why Xiaomi Airdots 2 is not charging a single headphone full of diagnostics

The situation when Xiaomi Airdots 2 stop charging on the one hand, is a common problem for budget owners. TWS-Often users are faced with the fact that the indicator on the problem earphone does not light up red when placed in the case, and the battery discharges faster than the second ear. This can be caused by both banal oxidation of contacts and software failure of the power controller.

Before you bring the device to the service or buy a new headset, it is worth conducting a comprehensive diagnosis. In most cases, the problem lies in the contamination of the contact areas or the software "hang" of the earphone, which simply ceased to see the case as a power source. Careful examination and the right sequence of actions will help to revive the device without financial costs.

It's important to understand that lithium polymer batteries in these compact devices are sensitive to deep discharges. If the earphone was left unused for a long time, it could go into "sleep mode" protection. In this case, the standard indication may not work immediately, requiring a longer time to "push" charging. Let's look at all possible causes and methods of eliminating them.

Mechanical causes and contamination of contacts

The most common reason why one Xiaomi Airdots 2 earphone fails to charge is oxidation or contamination of the contact pins. In the process of operation, earwax, skin fat and dust enter the metal pads, and over time, a dense film forms that prevents the passage of electric current from the case to the battery.

To fix this problem, you need to visually examine the bottom of the headphones and pins inside the charging case. Notice the presence of dark plaque or whitish oxides. Even a microscopic layer of dirt can create high resistance, which prevents the charge controller from starting the process of replenishing energy.

• 🧼 Take a cotton swab lightly soaked in isopropyl alcohol or a special contact cleaner, and thoroughly wipe the metal pads.
• 🔍 Use a toothpick or plastic spatula to neatly scrape visible contaminants off the surface of the contacts, trying not to damage the coating.
• 💨 Blow holes in the case with compressed air to remove fine dust that may have clogged into the indentations around charging pins.

⚠️ Warning: It is strictly forbidden to use water or aggressive solvents (acetone, gasoline) to clean electronics. Moisture trapped inside the case will cause a short circuit, and aggressive chemistry can melt plastic or damage the protective coating of contacts.

After cleaning, let the alcohol evaporate completely within 2-3 minutes. Only after that, place the headphones in the case and check if the indicator lights up. If the red light appears, then the problem was in poor contact. Regular cleaning will help to avoid a recurrence of the situation in the future.

Program failure and need for resetting

Sometimes the hardware is in good condition, but the headphone software is not working properly. The built-in Bluetooth controller and charging control module can "hang" in an error state, in which mode the device does not respond to the connection to the charger and does not turn on.

This problem requires a full Hard Reset, which forcefully resets the microcontroller and resets all temporary memory errors, and often after reset, the earphone begins to correctly detect the charging case again.

💡

If the headphone doesn't charge after reset, try leaving it in a case with a charger connected to the network for 30-40 minutes. Sometimes the batteries take time to get out of deep discharge.

The reset procedure for Xiaomi Airdots 2 is as follows:

1. Remove the device from the list of paired devices on your smartphone (Settings → Bluetooth → Forget the device).
2. Remove both earphones from the case.
3. Press and hold the touchpads on both headphones simultaneously for 20 seconds until the indicators flash red several times.
4. Put the headphones back in the case, close the lid and wait 10 seconds.

After doing this, try reconnecting the headset to your phone. If one of the headphones is still not charging, the problem may be deeper. It is important to reset when the case is at least 50% charged to ensure the process is stable.

Problems with charging case and cables

The Airdots 2 uses spring-loaded contacts inside the sockets, and over time, the spring may weaken and contact with the earpiece will disappear, especially if you touch the case slightly.

The problem can also be in the power supply: the use of powerful chargers for smartphones (with support for Quick Charge or Power Delivery) sometimes causes a conflict of protocols.

Try to charge the case from another source, for example, from USB-The computer port produces a stable 5 volts without pulsed jumps, which often helps to "swing" the battery of the case and adjust the charging of the headphones. If the charge started when connecting to the PC, then the problem was the power supply.

Deep battery discharge

If you didn't use the headset for a long time and left it dead, the battery could go into a deep discharge. Lithium-ion batteries have a minimum voltage threshold. Below this threshold, the chemical reactions slow down, and the standard charge controller stops seeing the battery, considering it to be malfunctioning.

In this state, the headphone indicator may not light up at all, even if you put it in a charged case. The protection system blocks charging to prevent bloating or damage to the item. However, this process is often reversible with the right approach.

Resuscitation of a deeply discharged battery requires a method of "shock" charging with low currents for a long time. Leave the headphones in a case connected to the network for 2 to 4 hours. Do not check their condition every 5 minutes, as this interrupts the recovery process.

⚠️ Warning: Do not try to open the headphone and apply voltage directly to the battery if you do not have experience with electronics.

If the indicator never catches fire after 4 hours of charging, it is likely that the battery life is completely exhausted. In budget models such as Xiaomi Airdots 2, the battery capacity is very small (about 40-50 mAh), and they degrade faster than in expensive analogues.

Hardware malfunctions and board oxidation

When software and cleaning don't work, you have hardware problems, and inside the headphone is a small circuit board, where the battery and the charge controller are soldered, and when moisture (sweat, rain) gets in, the conductive tracks corrosion.

Oxidation may be invisible to the eye, but it blocks the electric current completely, and often the soldering site of the battery wire to the board is oxidized, which requires disassembly of the device, which is extremely difficult because of the monolithic design of the Airdots 2 housing.

Another reason for the hardware failure is the failure of the charge controller itself, which is the circuit that regulates the current, and if it burns out because of a power surge or a failure, it won't charge, and it's only possible to diagnose it in a multimeter service center.

• 🔌 Check the integrity of the wires inside the headphone (opening is required) – often falls off the contact from the battery.
• 🔋 Measure the voltage on the battery with a multimeter - if it is lower 2.5-3.0 B, the battery is dead.
• 🔍 Examine the board under the magnifying glass for black dots (garg) or green plaque (oxidation).

It's not cost-effective to repair these headphones, and the cost of a handyman and parts often exceeds the cost of a new device, but if you have a warranty, take it to an authorized center.

Specificity of the work of touch panels

Users sometimes confuse the charging problem with the sensor.The headphone can charge (the indicator is on), but does not respond to touch, which makes it seem that it "does not work."Touch panels Xiaomi Airdots 2 sensitive to pollution and humidity.

If the earphone is turned on after charging but does not control music, try to wipe the outer surface with an alcohol napkin. The fat film from the skin can shield the signal. It is also worth checking whether the buttons are mechanically stuck (although in this model they are touch-sensitive, but dirt can create a “phantom press”).

In rare cases, flashing helps, but for the Airdots 2 model there are no official tools for the user.The update is automatically when you connect to a phone with the Xiaomi Earbuds app installed (for Android).

💡

If the headphone is charging but the sensor is not working, the problem is with the software or surface contamination, not the battery.

Frequently Asked Questions (FAQ)