Xiaomi AirDots 2 wireless headphones (also known as Mi True Wireless Earphones 2 Basic) remain among the most popular budget headphones. TWS-But many users have difficulty connecting the first time, because the device is not detected, the connection is interrupted or interferes. In this article, we will discuss all ways to pair with Android and iOS phones, as well as solve typical problems.
The AirDots 2 feature is that it doesn't have a button to turn on as we know it, instead, the headphones are activated automatically when you're removed from the case, and you need to press the touchpad for a long time to get into pairing mode. TWS-With headphones, this process may not seem obvious. We'll describe each step in detail, including hidden features like mono-connection or factory reset.
Preparation of headphones Xiaomi AirDots 2 to connect
Before pairing with your phone, make sure the headphones are fully charged and in working condition. The minimum charge for a successful connection is 20%, but it is better to bring it to 50-60%.
- 🔴 Red flashing – charge below 20%, you need to connect the case to the power source.
- 🟠 Orange constant – charge from 20% to 50%.
- 🟢 Green constant - charge above 50%.
- 🔄 Without indication - the case is discharged or defective.
If the indicator does not burn at all, try holding the button on the case for 10 seconds - this will reset the possible controller errors. Also check that the headphones are correctly placed in the nests of the case: the contacts on the headphones should fit tightly to the contacts in the case (they are located at the bottom).
⚠️ Attention: If the headphones do not respond to the extraction from the case (do not flash white light), this may indicate the discharge of the headphone batteries. 15-20 minutes, even if the case indicator is green - sometimes the charge controller "hangs".
Step-by-step: how to connect AirDots 2 to Android
The pairing with the Android phone (including Xiaomi, Samsung, Honor, Realme, etc.) takes no more than 1-2 minutes, if you follow the algorithm:
- Remove both earphones from the case. They will automatically turn on (white LED flashes).
- Press the touchpad on any headphone for 5-7 seconds until the indicators start flashing red and white alternately - this is pairing mode.
Once successfully connected, the headphones will stop flashing and light up with a permanent white light. Now you can use them to listen to music or calls. Note that AirDots 2 supports AAC protocol, so it is recommended to turn it on in the Bluetooth codec settings for better sound (if your phone allows it).
Headphones are displayed in the list of connected devices |Indicators are burning in constant white |The sound is played synchronously in both headphones |The microphone works when calling-->
⚠️ Attention: On some firmware MIUI (For example, on the Redmi Note. 8/9) You may have a problem when the headphones are only connected in mono mode (sound only goes to one headphone). Solution: turn them off in Bluetooth settings, then re-start the search and connect again.
Xiaomi AirDots 2 pairing with iPhone (iOS)
The process of connecting to an iPhone or iPad is almost identical to Android, but there are nuances with the codec. iOS uses AAC by default, which provides good audio quality, but some users note delays when watching videos. To minimize lags:
- Activate the pairing mode on the headphones (clutch the touch panel until flashing red/white).
- On the iPhone, go to Settings → Bluetooth.
- Select Mi True Wireless Earphones 2 from the list.
- Once connected, open Control Point → Hold Play icon → Select AirDots 2.
- Enable the option "Use as stereo headphones" (if available).
If the sound is interrupted or there is interference, try turning off Bluetooth on other devices nearby (such as a laptop or smartwatch) – they can cause interference.
Solving Connection Problems
If Xiaomi AirDots 2 headphones don’t connect or are not working smoothly, check out the following points:
| Problem. | Possible cause | Decision |
|---|---|---|
| Headphones not detectable | The pairing mode is not activated | Press the touchpad for 10 seconds before flashing red/white |
| The sound is only in one headphone. | Failure of synchronization between headphones | Return both headphones to the case, retrieve and reconnect. |
| Permanent communication breakdowns | Interference from other Bluetooth devices | Disable unnecessary devices or reboot your phone |
| Headphones are discharged quickly | Outdated firmware | Update the software via Mi Home (if available) |
If none of the methods helped, reset the settings:
- Put both earbuds in the case.
- Open the case lid.
- Press the touch panels on both headphones simultaneously for 15 seconds until the indicators start flashing red 3 times.
- After resetting, reconnect the headphones as when you first use them.
What if the reset didn't help?
How to connect only one headphone (monomodem)
Xiaomi AirDots 2 supports mono-connection, which is convenient for calling or listening to podcasts.
- Only remove one headphone from the case (left or right).
- Press the touchpad on it for 3 seconds until the indicator starts flashing white with pauses.
- Connect it to your phone via Bluetooth as usual.
Note that in mono mode, the microphone will only work on the earphone connected. If you need to switch to stereo, just pull the second earpiece out of the case, they sync automatically, but sometimes you need to re-pair.
💡
If mono mode does not turn on, try first to connect both headphones, and then turn off the phone that is unnecessary in the Bluetooth settings. This will reset the current session and allow you to use one earphone.
Update firmware and additional functions
The proprietary Mi Home app (available for Android and iOS) allows you to update AirDots 2 firmware if you have updates available for your model.
- Install Mi Home from the App Store or Google Play.
- Sign up or sign in to your Xiaomi account.
- Connect the headphones to the phone via Bluetooth.
- In the app, click Add Device → Headphones → Mi True Wireless Earphones 2.
- If you have an update, you'll see a notification. Follow the instructions on the screen.
Among the useful features in Mi Home:
- 🔊 Equalizer setting (bass, high frequencies).
- 🎤 Game mode (reduces the latency of sound).
- 🔋 Display the charge level of each headphone and case.
- 🔄 Reset to factory settings directly from the app.
Importantly, not all of the features may be available for AirDots 2, as they are in the budget lineup, for example, active noise cancellation (ANC) is not available in this model.
💡
Updating your firmware can solve connectivity problems, improve connectivity stability, and add new features, but don’t interrupt the upgrade process — it can knock your headphones out of order.
Long-term extension advice
To make Xiaomi AirDots 2 last longer, follow the following simple recommendations:
- 🔌 Do not leave your headphones on charge for more than 24 hours – this reduces battery life.
- 🧼 Clean the contacts of the case and headphones with a soft brush or cotton swab with alcohol 1 time per month.
- 🌡️ Avoid overheating – do not leave the case under direct sunlight or near heat sources.
- 📵 Turn off Bluetooth on your phone when you’re not using headphones – this reduces battery load.
The average battery life in AirDots 2 is about 1.5-2 years in heavy use, and if the battery life is reduced to 1-1.5 hours, it is a signal that the batteries need to be replaced (in the service center).