How to turn on and use cruise control on the Xiaomi Pro 2: the complete guide

Introduction: Why do you need cruise control on an electric scooter?

The Xiaomi Pro 2 has long been popular with urban residents for its combination of power, compactness and technology. One of the most popular features is cruise control, which allows you to maintain a constant speed without retaining gas. This not only reduces arm fatigue during long trips, but also makes control more smooth, especially on flat sections of the road or bicycle paths.

However, many Xiaomi Pro 2 owners face difficulties in first enabling this feature. Unlike in-car systems where cruise control is activated with a single button, on scooters, the process requires knowledge of specific combinations and conditions. In this article, we will discuss all the activation methods, configuration nuances and typical errors that interfere with the correct operation of the function.

It’s important to understand that cruise control on the Xiaomi Pro 2 doesn’t work the same way as on newer models (like the Pro 3 or 4 Pro).There’s no separate button here, the feature is integrated into the throttle control logic, which means that you have to perform a certain sequence of actions to enable it, which we will describe in detail below.

Technical requirements for cruise control operation

Before you attempt to activate cruise control, make sure your scooter meets the following conditions:

• 🔋 Battery charge at least 20%. At low charge level, the system can block the function to save energy.
• 📱 The firmware version is at least 1.3.6 (for the Xiaomi Pro 2). In earlier versions, cruise control may not work stable or at all.
• 🛠️ Throttle and brake failure: If the scooter detects errors in the control system, the cruise control will automatically shut down.
• 🚲 Speed of at least 10 km/h. The function is not activated at too low speeds.

If your scooter has not been updated since purchase, there is a high probability that cruise control is simply not provided in the current version of the software. You can check the current firmware through the official Mi Home application (Device → Software Update).

Step-by-step: how to turn on cruise control

The activation algorithm for the cruise control on the Xiaomi Pro 2 consists of three key steps, which are important to follow consistently and without long pauses.

1. Accelerate to a stable speed (15-20 km/h is recommended). Keep the throttle in one position for at least 5 seconds. The system should "remember" the current speed.
2. Release the gas handle for 1-2 seconds, then press it again to the same level, and if done correctly, the scooter will continue to move without holding the throttle.
3. Activation confirmation: the CRUISE indicator will light up on the display (on some firmwares there is a lock icon next to the speed).

If the scooter starts to brake after releasing the throttle, then the function is not activated. Repeat the attempt, keeping the speed longer (up to 8 seconds).

The gas handle does not catch and returns to the original position |

No active errors on the display (for example, E01 or E02)|

The scooter moves on a flat surface without slopes |

Brake levers are not clamped (even partially)-->

Critical detail: on the Xiaomi Pro 2, cruise control is turned off automatically when any brake is pressed, a sharp change in slope or a speed drop below 8 km / h. This is done for safety, so do not try to “cheat” the system.

Common mistakes and their solutions

Even if you follow the instructions correctly, cruise control may not be activated, and here are the most common reasons and ways to eliminate them:

The problem with non-original firmware deserves special attention, many owners install custom versions of software to overclock the scooter or turn off restrictions. However, in 80% of cases this leads to the loss of cruise control, since informal firmware often removes this feature as “unnecessary.” If you have previously changed the software, return the original version through Mi Home or service center.

💡

Before updating your firmware, reset your scooter settings to factory settings (Settings → Reset in the Mi Home app) to reduce the risk of errors when installing new software.

Safety in the use of cruise control

Cruise control makes driving much easier, but requires a greater focus on the environment.

• 🚦 Do not use the function in urban traffic. The scooter will not be able to react quickly to pedestrians or obstacles.
• 🌧️ Disable cruise control on wet or slippery roads. Automatic speed maintenance can lead to loss of control.
• 📉 Watch your battery power. At levels below 15%, the function will shut down, which can come as a surprise at high speed.
• 🛑 Always keep your hand over the brake.Cruise control shuts down when you press the brake, but the reaction must be instantaneous.

⚠️ Note: On the Xiaomi Pro 2, cruise control is not compatible with Eco mode. If you activate power saving, the feature will not be available until you switch to Sport or Standard mode.

Also, keep in mind that cruise control does not work when reversing (if supported by your firmware), which is a logical limitation, since reverse is usually used for low-speed maneuvers where automatic speed maintenance is not relevant.

Comparison with other Xiaomi models

The cruise control functionality on the Xiaomi Pro 2 is different from the brand’s newer and older models.

As you can see from the table, the Xiaomi Pro 2 requires a longer throttle retention compared to the Pro 3, where the function is activated with a simple double click. This is due to the features of the first version of the controller. It is also worth noting that on the Pro 2, cruise control is not stored after the scooter is turned off - it will have to be turned on again on each trip.

Additional settings and tuning

For power users who want to expand cruise control, there are ways to fine-tune it through informal tools, such as using the ScooterHacking Utility (SHU) utility, you can:

• 🔧 Change the retention time of the throttle for activation (default 5 seconds).
• 📈 Set the minimum speed threshold (e.g., reduce from 10 to 8 km/h).
• 🔄 Disable auto-disconnection when braking (not recommended for safety reasons!).
• 🔋 Activate cruise control in Eco mode (requires firmware modifications).

However, before using such tools, consider:

⚠️ Note: Any changes to the firmware through SHU or similar utilities deprive warranty and can lead to unstable operation of the scooter, in particular, there are cases when, after modification of the cruise control, the scooter spontaneously accelerates or brakes.

If you do decide to tuning, follow this algorithm:

1. Connect the scooter to the PC through BLE-adapter (e.g, HM-10).
2. Run ScooterHacking Utility and select the M365 Pro 2.
3. In the Cruise Control section, make changes (we recommend starting with the minimum values!).
4. Save the settings and restart the scooter.

💡

Using informal tools to set up cruise control can lead to unpredictable scooter behavior.If you are not sure about your skills, it is better to limit yourself to standard features.

FAQ: Answers to Frequent Questions