How to turn on Xiaomi Amazfit Bip smartwatch: 5 working ways

The Xiaomi Amazfit Bip is one of the most popular wearables due to its combination of functionality and affordable price. However, even with such a reliable gadget, sometimes there are problems: the watch does not respond to the on button, the screen remains black after discharging, or the device freezes after updating the firmware. If your Amazfit Bip (including the Bip Lite, Bip S or Bip U models) refuses to turn on, do not panic.

In this article, we’ll look at all the possible reasons why your watch might not turn on, and provide step-by-step instructions for each case, from basic actions (charging, rebooting) to advanced methods (resetting via the Mi Fit or Zepp app), and how to distinguish hardware from software failure, and when to contact the service center.

1. Battery charge check - the first step

The most common reason why the Amazfit Bip doesn’t turn on is a fully discharged battery. Despite the stated life of up to 45 days, with active use (GPS, notifications, constant synchronization), the watch can discharge in 5-7 days, and the screen can remain black even when charging is connected if the charge has dropped to a critical level.

What to do:

🔌 Connect the watch to the charger using the original cable (or certified analogue). 5V/1A or 5V/2A — More powerful blocks can damage the charging controller.
⏳ Leave the watch on charge for at least 30 to 60 minutes. In a deep discharge, the charging indicator (red or green LED) may not immediately light up.
🔍 Check the contacts on the watch and charger - they should be clean and not oxidized. If necessary, gently wipe them with a cotton swab soaked in alcohol.

📊 Your Amazfit Bip is discharged faster than before?

Yeah, it's a lot faster.

No, it's working as usual.

I don't know.

I have another problem.

If after an hour of charging the clock still does not respond:

🔄 Try another charger or USB-port (for example, on a computer).
📱 Connect your watch to your smartphone via the Mi Fit or Zepp app – sometimes it’s detected even when the screen is off.

⚠️ Note: Do not use wireless chargers or quick-charging adapters (Quick Charge, VOOC They can disable the Amazfit Bip battery due to incompatible protocols.

2. Forced reset (Hard Reset)

If the watch doesn't respond to the button but the battery is charged, there may have been a software failure, in which case a forced reboot (an analogue of "hard reset" on smartphones) will help, which works for all Bip models, including the Bip S and Bip U.

Instructions:

Make sure that the watch is at least 10-15% charged (otherwise the reset may be interrupted).
Press the single physical button on the right side of the case.
Hold it for 15-20 seconds until the screen blinks or the Amazfit logo appears.
Release the button and wait for the full download (can take up to 2 minutes).

Charge the watch at least 10% |

Disconnect from the smartphone (if connected)|

Make sure the button is not stuck |

Wait 1-2 minutes after the reset-->

If the clock is “hanging” again:

🔄 Repeat the procedure 2-3 times in a row.
📲 Try syncing your watch with the Mi Fit app – sometimes it “wakes up” the device.

⚠️ Note: On the Amazfit Bip U Pro and Bip S Lite, long-term button retention (more than 30 seconds) can trigger recovery mode. If the screen says Recovery Mode, release the button and wait for the automatic reboot.

3. Reset settings via the Mi Fit/Zepp app

If the forced reboot didn’t work, but the watch is determined by the smartphone (the Mi Fit or Zepp app displays their model), try a software reset.This method deletes all user data, but often solves the “hang” problems.

Step-by-step instructions for Mi Fit:

Open the Mi Fit app and go to Profile → Devices → Amazfit Bip.
Slap the icon. ⚙️ (settings) in upper right corner.
Select Disable Device (or Delete Device in New Versions).
Confirm the action and wait for the process to be completed.
Reboot the watch (press the button for 10 seconds) and reconnect it through Add the device.

For the Zepp app (relevant to Bip S, Bip U):

Go to Profile. → My devices. → Amazfit Bip.
Select the device settings → Reset settings.
Confirm the reset and wait for the clock to reset.

Annex	The way to dump	Time of procedure	Is the data preserved?
Mi Fit	Profile → Devices → ⚙️ → Shut down.	1-3 minutes	❌ No (all settings are deleted)
Zepp	Profile → My devices → Settings → Reset	2-5 minutes	❌ No (except for the last time you have synchronized)
Manual reset (button)	Holding the button 15-20 seconds	30-60 seconds	✅ Yes (unless you download Recovery Mode)

💡

If the watch doesn’t connect to the app after reset, try removing it from the device list in your smartphone’s Bluetooth settings, and then repeat pairing.

4. Checking for hardware malfunctions

If none of these methods worked, it may be the hardware that's the problem, and here are the most common malfunctions and their signs:

🔋 Faulty battery: the watch only turns on when connected to charging, but immediately turns off after disconnection.
🖥️ Damaged screen or plume: The watch vibrates at notifications, but the screen remains black (check if the backlight glows in bright lights).
🔌 Oxidized charging contacts: the clock is not charging or charging is interrupted, and visually visible green or white deposits on the contacts.
💧 Moisture: After contact with water, the watch stops turning on (even if the model has protection). IP68).

How to diagnose:

Connect the watch to charge and check if the case is heating up. Too much heat (over 40-45 ° C) indicates a malfunction of the battery or power controller.
Light a flashlight on the screen at an angle - if you see a dim image of the interface, the problem is in the backlight or plume.
Try connecting the watch to another smartphone, and if it's identified as an unknown device (Mi Band or LE-Device), the Bluetooth module may have been damaged.

What to do if the watch is wet?

If the Amazfit Bip stopped turning on after water hits: 1. Immediately disconnect them from charging (if connected). 2. Wet the case with a dry wipe, do not shake or blow a hairdryer! 3. Place the watch in a sealed bag with silica gel (from the shoe box) for 24-48 hours. 4. Do not try to turn them on ahead of time - this can cause a short circuit. 5. If the watch does not turn on after drying, contact the service (repair after moisture is possible, but not always rent).

⚠️ Warning: If the watch case is swollen or deformed, do not try to disassemble them yourself - this can lead to a fire battery.

5. Manual firmware update

Sometimes the Amazfit Bip watch is not turned on due to a failed firmware update (for example, if the process is interrupted due to a discharge or loss of communication with the smartphone), in this case, manual firmware through official tools will help.

You'll need:

💻 Computer with Windows or macOS.
🔌 Original. USB-cable.
📥 Firmware for your model (you can download it on amazfitwatchfaces.com or XDA Developers).
🛠️ Amazfit Bip Tool or Gadgetbridge (for advanced users).

Step-by-step:

Download the archive with firmware and unpack it in a folder.
Connect the watch to your computer via a charging cable (they must be turned off).
Run the Amazfit Bip Tool and select the firmware file (.fw or.bin).
Press Start Flash and wait for the process to complete (about 5-10 minutes).
After successful firmware, the clock will automatically restart.

💡

Handheld firmware removes all data from the watch and restores factory settings, and use this method only if other methods have not worked, as it requires technical skills.

If the firmware fails:

🔌 Try another one. USB-port.
🔄 Restart your computer and repeat the process.
📥 Make sure that the downloaded firmware is suitable for your model (e.g. Bip Global or Bip China).

6. When to contact the service center

If you’ve tried all the methods, but the Amazfit Bip still doesn’t turn on, it’s likely that the problem needs professional repair.

🔥 The clock is heated for no reason (even when it is off).
💥 On the body visible traces of swelling or leakage of the battery.
🔌 No charge comes from any power source.
📱 The clock is not defined by any device (smartphone or computer).
💧 There was a ingress of moisture, after which the gadget stopped working.

Where to repair:

🏢 Official Xiaomi service centers: repair warranty (if the deadline has not expired) or paid. mi.com/ru/service.
🔧 Informal workshops: cheaper, but no guarantee for work.We recommend choosing with good reviews (for example, on Yandex.Maps or 2GIS).
📦 Self-replacement: If you're an experienced user, you can order spare parts (battery, screen, plume) on AliExpress and replace them yourself.

Type of repair	Cost (roughly)	Timeline	Guarantee
Battery replacement	800–1 500 ₽	1-3 days	1-3 months
Screen/shoe replacement	1 200–2 500 ₽	2-5 days	1 month
Repair after moisture	1 500–3 000 ₽	3-7 days	Not always.
Diagnostics + firmware	500–1 000 ₽	1 day	1 month

⚠️ Note: If your watch is warranty (usually 12 months from the date of purchase), do not disassemble them yourself - this will void the warranty obligations.

FAQ: Frequent questions about incorporating Amazfit Bip

The clock vibrates, but the screen doesn't turn on. What do we do?

This is a typical sign of a problem with the backlight or the screen plume. Try: Bring the watch to a bright light source — if the image is barely visible, the backlight is defective. Forced to reset the clock (hold the 20 seconds button). If it does not help, contact the service to replace the plume or screen.

After the firmware update, the clock doesn't turn on. How do you roll back?

If the update failed, try: Reset your settings via Mi Fit/Zepp (if the clock is fixed); manually run the old version (instruction in section 5). If nothing helps, contact the firmware service via the programmer. You can download old firmware versions on the XDA Developers or 4PDA forums.

The watch only turns on on when charging. Is it a battery?

Signs of a faulty battery: The watch only works when connected to the grid; the battery runs out in a few hours (previously held longer); the case swells slightly near the charging contacts; solution: battery replacement in the service (cost) ~1 000 ₽).

Can I turn on the Amazfit Bip without a charger?

If the battery is completely drained, however, if the watch has at least a minimal charge, try: Connect it to a power bank or computer via USB. Use wireless charging (only for models with Qi support, such as the Bip U Pro); try to wake the watch through the Mi Fit app (sometimes they respond to synchronization).

The watch is on the Amazfit logo.

This means that there was a failure when the system booted. Solutions: Hold the button for 30 to 40 seconds until the clock restarts. If it doesn't work, reset it through the Mi Fit/Zepp app. In extreme cases, flash the watch manually (section 5). If the logo flashes endlessly, it's a sign of damage to the firmware. Reflashing is required.