Mi Band 6 won’t turn on after resetting: Complete Recovery Guide

Resetting the Xiaomi Mi Band 6 is standard when selling a device, fixing software failures or preparing for a new firmware. However, many users face a problem: after a hard reset, the bracelet ceases to respond to presses, does not turn on or sync with the smartphone, 80% of the time this is due not to hardware failure, but to the wrong sequence of actions on the first launch.

In this article, we’ll look at all possible scenarios, from basic activation via Mi Fitness to manual reconnection if the bracelet is not determined by the phone. Particular attention will be paid to hidden Bluetooth settings, which often block connection after reset. The instruction is relevant for firmware 2026 and takes into account the latest updates to the Xiaomi Wear app (formerly Mi Fit).

Why does Mi Band 6 not turn on after resetting?

Before we get to the solution, it is important to understand the cause of the problem: resetting the settings on the Mi Band 6 not only resets user data (steps, pulse, notifications), but also system parameters of communication.

• 🔋 After the reset, the device uses up to 30% of the charge to reload the modules. If the charge was below 20% before the reset, the bracelet may not turn on.
• 📱 The older version of Mi Fitness (up to 5.6.0) does not support re-activation after reset.
• 🔄 Incomplete reset: If you interrupt the procedure (for example, untie the bracelet from the phone until the end of the reset), the device will freeze during the initialization stage.
• 🛡️ Bluetooth lock. On Android 12+ The system can automatically limit background activity of Mi Fitness, which interferes with synchronization.

In rare cases, the problem lies in a hardware failure, such as damage to the charging contacts or memory chips, but such failures usually occur before reset (the bracelet spontaneously turns off, does not hold the charge). If the device worked stably before the reset, it is likely to be the fault of the software.

Preparation for Including: What to Do Before Activation

Before you try to turn on Mi Band 6, follow the mandatory preparatory steps, which will save time and prevent typical errors:

1. Charge to 100%. Connect the bracelet to the charger for 30-40 minutes, even if the indicator is not on. Use the original USB-A → 2-pin cable (voltage 5V/0.5A).
2. App Update: Remove the old version of Mi Fitness and install the fresh one from Google Play or the App Store.
3. Clean Bluetooth cache. On Android: Settings → Apps → Mi Fitness → Memory → Clear cache. On iPhone: Settings → Bluetooth → Forget this device (Mi Band 6).
4. Compatibility check. Mi Band 6 officially supports Android 6.0+ and iOS 10.0+. On older versions, sync may not work.

If the bracelet was previously linked to another Xiaomi account, make sure you log out on your phone. At the same time, the device can only be synced to one profile. When you try to connect to another account, the bracelet will give an error of 0x1004 (association conflict).

💡

If the charging indicator doesn't light up, try cleaning the bracelet contacts with an alcohol napkin. Metal oxidation is a common cause of power problems.

Step-by-step: how to turn on Mi Band 6 after reset

If you're done, you go to activation. It's important to follow the instructions in strict order, because skipping the steps can cause you to fail again.

Charge the bracelet to 100%|Install the latest version of Mi Fitness|Enable Bluetooth and geolocation on your phone|Remove the old bracelet binding in the application (if it was)|Press the Mi Band 6 touch button before vibration-->

Step 1: Physically activate the bracelet

After reset, Mi Band 6 is in sleep mode to wake it up:

1. Place the bracelet on the charger for 5-10 seconds (even if it is charged).
2. Press and hold the touch button (below the screen) for 10-15 seconds until you feel a triple vibration.
3. Release the button. The Mi logo should appear on the screen (if not, repeat steps 1-2).

Step 2: Connect to Mi Fitness

Now you need to link the bracelet to the account:

1. Open Mi Fitness and log in (or create a Xiaomi account).
2. Click Profile → Add Device → Bracelet → Mi Smart Band 6.
3. Allow the app to access Bluetooth, Notifications, and Geolocation (required!).
4. Wait for the app to find the bracelet (it can take up to 2 minutes) and the Mi Band 6 screen will show a confirmation code — compare it to the code in the app.
5. Click Confirm in Mi Fitness and wait for the synchronization to end (indicator - green tick).

If you fail to find your device during the connection phase, go to Bluetooth Settings on your phone and manually select the Mi Band 6 from the list of available devices. Then go back to Mi Fitness and try again.

Step 3: Configure after activation

After successful connection:

• 🕒 Update the time and date (automatically synced with the phone).
• 🔔 Set up notifications in the Device Profile → Notifications (allow access for messengers and calls).
• 🏃 Select activity goals (steps, sleep, pulse) in the Health section.
• 🔄 Check firmware updates in Device Settings → Update of the PO.

What to do if Mi Band 6 is not turned on: common errors and solutions

Even with the exact following of the instructions, there can be problems, and let's look at the typical scenarios and how to fix them.

If neither method worked, check the bracelet on another phone. If the problem persists, there is likely a hardware malfunction (such as detachment of the display plume or failure of the power controller). In this case, contact the service center Xiaomi – repairs will cost 1,500-3000 ₽ (depending on the breakdown).

💡

More than 60% of the problems with turning on the Mi Band 6 after reset are solved by updating the Mi Fitness app and clearing the Bluetooth cache.Before carrying the bracelet for repair, make sure you have tried all the software methods.

How to Reset Your Settings to Mi Band 6 (If the Previous One Didn't Help)

If the bracelet is turned on but is not working correctly (screen glitches, data is not synchronized, communication is lost), perform a full hard reset, which will delete all data and return the device to factory settings.

There are two ways to discharge:

Method 1: Through the menu of the bracelet

1. Swipe your finger across the Mi Band 6 screen to the left until the More menu (three dots) appears.
2. Select Settings → Resetting settings.
3. Confirm the action by clicking the tick, the bracelet will reset and return to the factory settings.

Method 2: Forced reset (if the bracelet does not respond)

If the screen is not working or the bracelet is frozen:

1. Connect the Mi Band 6 to the charger.
2. Press and hold the touch button for 30 seconds until you feel a double vibration.
3. Release the button. The bracelet will reset and reset (the process will take up to 3 minutes).

After reset, repeat the activation procedure as described in the section above. Please note that all data (steps, sleep, workouts) will be permanently deleted. If you care about statistics, export it to Google Fit or Apple Health before reset via Profile → Data Export to Mi Fitness.

💡

If the bracelet does not turn on again after reset, try to connect it to another phone (preferably on iOS - Apple's system often correctly determines devices after the reset).

Data recovery after reset: can statistics be returned?

One of the most common questions after a reset is how to return your activity history. Unfortunately, Xiaomi does not provide an official way to recover data deleted during hard reset.

• 📊 Exports to Google Fit/Apple Health. If you've previously synced Mi Fitness with these services, you can import the data back:
• 💾 Backup of Mi Fitness. The app automatically creates backups once a week (if you have Settings enabled). → Backups to restore:

Third-party utilities

Mi Band Tools

Notify & Fitness

Important: not all data can be recovered, for example, detailed sleep and heart rate statistics are stored in the wristband memory only and deleted when reset, and the overall readings (daily steps, calories) are easier to recover.

⚠️ Note: Do not use unofficial firmware (e.g. Custom Firmware for Mi Band 6) in an attempt to recover data.This may result in a complete loss of the bracelet functionality and cancellation of warranty.

FAQ: Frequent questions about turning on Mi Band 6 after reset