Bluetooth on Xiaomi scales not turned on? full activation and connection guide

Xiaomi's smart scales are not just a weight measuring device, but a full-fledged body composition analyzer that transmits data to a smartphone via Bluetooth. However, many users face a problem: the scales are not detected by the phone, the connection is constantly reset, or the Bluetooth indicator does not light up at all. In 90% of cases, the problem lies not in the breakdown, but in the wrong activation of the module or synchronization errors.

In this article, we will discuss how to turn on Bluetooth on Xiaomi scales for all popular models (Mi Body Composition Scale 2, Smart Scale 2, Mi Scale, etc.), consider hidden settings that the manufacturer does not specify in the instructions, and give a checklist to eliminate typical errors.

If your scale suddenly stopped plugging in after you upgraded your firmware or changed your smartphone, here's the solution, and for those of you who've just unpacked your device, we've prepared a step-by-step guide with a photo of each step.

1.What Xiaomi scale models support Bluetooth?

Not all Xiaomi smart scales are equipped with a Bluetooth module - some budget models only transmit data over Wi-Fi or require a special hub. To avoid wasting time, check your model in the table below:

If your model isn’t on the list, check the box or documentation – look for the Bluetooth SIG logo or a mention of BLE. Libras without Bluetooth are usually cheaper and have the word Lite in the name.

⚠️ Note: Xiaomi Mi Smart Scale Lite scales do not support direct connection to the phone. They need a Mi Home Hub (gateway) or a router with Mi Mesh support.

2.How to turn on Bluetooth on Xiaomi scales: basic instruction

In most Xiaomi models, the Bluetooth module is activated automatically when first turned on. However, if the scales have already been used or have been reset, manual activation may be required.

1. Set the scales on a flat, hard surface (not on a carpet!).
2. Insert batteries (if not installed). Mi Body Composition Scale 2 needs 4 AAA batteries, Smart Scale 2 needs 3 AAA batteries.
3. Press the scales with one foot - the display with the inscription 0.0 should light up.
4. Wait 5-10 seconds: If Bluetooth is active, an icon will appear on the screen. 📶 or BT.
5. If there is no icon, press and hold the on button (usually under the display) for 5 seconds until the indicator blinks.

On touch-controlled models (such as the Mi Body Composition Scale 2), just touch the display to activate Bluetooth. If you don't establish a connection after this, go to the "Problem Solutions" section.

Install batteries with correct polarity|Put the scales on a flat surface|Check the battery charge (if there is an indicator)|Press the scale to activate the display|Wait for the Bluetooth icon to appear-->

Important: Xiaomi scales use the BLE (Bluetooth Low Energy) protocol, which consumes battery power economically. However, if the batteries are discharged below 20%, the Bluetooth module may not turn on. Replace the batteries if the indicator flashes red.

3.Sync scales with phone via Mi Fit or Zepp Life

Activating Bluetooth on scales is only half the battle, and to get data to your smartphone, you need to set up the connection in the official app correctly. Consider the process with Mi Fit (the steps are similar for Zepp Life):

1. Download and install Mi Fit from Google Play or the App Store.
2. Sign up or sign in to your Xiaomi account (required!).
3. Click Profile → Add the device → Libra.
4. Select your model from the list (e.g. Mi Body Composition Scale 2).
5. Press Connect and wait for the app to find the scales. The scale screen should have an icon on it. 📶.
6. Confirm the pairing in the request window on the phone.

If the scales are not detectable:

• 🔄 Reboot Bluetooth on your phone (turn off and turn on in settings).
• 📱 Update the Mi Fit app to the latest version.
• 🔋 Check Permissions: App must have Bluetooth, Location and Warehouse access.
• 🚫 Turn it off. VPN — It can block the connection to Xiaomi servers.

Critical detail: Android 12+ and iOS 15+ require geolocation permission to operate BLE. Without it, the scales won't connect!

Mi Fit|Zepp Life|Apple Health|Google Fit|Other-->

4. Why Bluetooth on Xiaomi scales is not included: top-5 cause

If you’ve followed all the steps, but the Bluetooth module is still inactive, the problem may lie in one of the following factors:

• 🔋 Discharged batteries – even if the display is turned on, BLE Replace the cells with new ones (preferably alkaline).
• 📱 Outdated firmware of scales – some models (such as Mi Scale 1) require an update via Mi Fit.
• 🛡️ Lockdown MAC-Addresses – if the scales have previously connected to another phone, they can “remember” the old device).
• 📡 Interference from other devices such as microwaves, 2.4GHz Wi-Fi routers or other Bluetooth gadgets can cause interference.
• 🔧 Hardware malfunction - if the scales fell or were exposed to moisture, the Bluetooth module could be damaged.

The most common reason is conflict with other Bluetooth devices, for example, if you have wireless headphones or a fitness bracelet nearby, they can clog the channel, turn off all the extra gadgets and try again.

5. Problem Solving: Scales are not connected to the phone

If Bluetooth is on (the indicators are on), but the phone does not see them, use this checklist:

Reboot phone |Remove scales from the list of associated devices in Bluetooth settings |Update Mi Fit/Zepp Life |Try to connect from another phone |Reset the scales to factory settings-->

Resetting the scales to the factory settings helps in 70% of cases.

1. Make sure the scales are off (display is out).
2. Turn the scales over and find the reset button (usually next to the battery compartment).
3. Press and hold the button for 10-15 seconds until the indicator blinks.
4. Release the button and the scales will reset.

On models without a physical reset button (e.g., Mi Body Composition Scale 2), reset via the app:

Mi Fit → Profile → Your scale → Settings (⚙️) → Reset device

⚠️ Note: After reset, all stored data (user profiles, measurement history) will be deleted from the scales, but will remain in the Mi Fit app if synchronization was previously performed.

If the reset didn’t help, try an alternative way to connect:

• 📲 On Android: Enable Developer Mode → Turn on Bluetooth HCI Sniffer (can help with driver conflicts).
• 🍎 On iPhone: Go to Settings → Bluetooth, find the scales in the list and click Forget this device, then repeat pairing.

6.How to connect Xiaomi scales to multiple phones?

Officially, Xiaomi scales support synchronization with only one device via the Mi Fit.

Method 1: Using a single Mi Account

If both phones log in under the same Xiaomi account, the data will be synchronized automatically.

Method 2: Manual addition via Bluetooth

1. On the first phone, turn off the scales in Mi Fit (but don't delete them!).
2. On the second phone, turn on Bluetooth and find the scales in the list of available devices (the name will be type). MI_SCALE_XXXX).
3. Connect manually (without Mi Fit).
4. Run the Mi Fit on the second phone and add the scales as a new device.

Method 3: Export of data

In Mi Fit, you can export your measurement history to Google Fit or Apple Health, and then import it to another phone.

Mi Fit → Profile → Settings → Data Export

⚠️ Note: When connecting scales to multiple phones, synchronization errors can occur at the same time. It is recommended to use one main phone for measurements, and on the second one, only view data through the cloud.

7.Alternative applications for connecting Xiaomi weights

If Mi Fit or Zepp Life is not suitable (for example, due to regional restrictions), you can use third-party applications:

To connect through third-party applications:

1. First, untie the scales from Mi Fit (in the device settings).
2. Turn on Bluetooth on the scales (badge) 📶 burn).
3. Run an alternative application and search for devices.
4. Choose your scales from the list and confirm the pairing.

Important: Some apps (such as Sleep as Android) require root rights to Android to fully access the scale data, and without them, functionality may be limited.

💡

If the scales are not defined in any application, try changing the region in Mi Fit to China (in your account settings).

FAQ: Frequent questions about Bluetooth on Xiaomi scales

💡

If Xiaomi scales are not connected to the phone, 95% of the time the problem is solved by replacing batteries, resetting settings or updating Mi Fit. Hardware malfunctions are extremely rare and are usually associated with falling or getting moisture.