How to turn on Xiaomi treadmill: instructions for all models (2026)

Xiaomi’s treadmills are not just simulators, but smart devices with integration into the Mi Home ecosystem, support for mobile apps and advanced sensors, but even such tech gadgets can have problems with inclusion, from banal lack of power to software failures. This article will help you figure out how to properly run Xiaomi’s treadmill – whether it’s a compact WalkingPad A1 Pro, KingSmith foldable R2 Or professional Yeelight Treadmill.

We'll look at all the scenarios that we can think of, from the first switch on after you buy it to the recovery of your performance after a long period of downtime, and we'll focus on the typical user errors that lead to a remote lock or a lack of response to buttons, and if your track doesn't show signs of life, don't rush it to the service, because in 80% of cases, you can solve the problem yourself in 5-10 minutes.

For convenience, the instructions are divided into blocks by model and type of malfunction. Use the table of contents to quickly move to the desired section. And if your model is not mentioned, do not worry: the principles of inclusion and diagnosis are universal for the entire Xiaomi line.

Preparation for the first turn on: what to do before launch

Before you press the power button, make sure that Xiaomi’s treadmill is ready to go, and neglecting these steps is the main cause of breakdowns in the early days of operation.

First, check the package. The box should have:

• 🔌 Power adapter (if the model requires connection to the socket)
• 📱 Control panel (some models are built into handrails)
• 🔧 Key for adjusting the inclination (if provided)
• 📄 Instructions in Chinese/English (Russian can be downloaded at Mi Home)

Second, place the track on a flat surface. Skewers more than 2.° This can cause the engine to automatically shut down. Use a building layer or an alignment app on your smartphone. C2) First unlock the locks - usually it is a lever under the base.

💡

If the floor in the room is wooden or laminated, put rubber pads under the legs of the tracks, which will reduce vibration and noise, and prevent slipping while running.

Third, plug in the power. Most Xiaomi models have an adapter connector on the back, under the protective cover. Make sure the voltage is up to the requirements (usually 220–240V). For the WalkingPad R2 and KingSmith K3 requires a grounded outlet - ignoring this rule can lead to an electric shock.

2. Standard inclusion: buttons and sequence of actions

The process of turning on depends on the Xiaomi treadmill model, and the algorithm for the most popular devices is given below:

If the track does not respond to the buttons:

1. Check if batteries are inserted into the remote (usually) CR2032 or AAA).
2. Make sure there is no lock from children (on some models it is activated by long pressing on Lock).
3. Try rebooting the device: Remove the plug from the socket for 30 seconds, then plug it back in again.

3. Enable via the Mi Home app: step-by-step instructions

All modern Xiaomi treadmills support control through a proprietary app, which is not only convenient, but also necessary to unlock some features (for example, personal training or synchronization with the Mi Band).

To turn on the track through Mi Home:

1. Download the app from the App Store or Google Play.
2. Sign up or sign in to your Xiaomi account (required!).
3. Press «+» → «Add the device» → Choose the category "Fitness and Health».
4. Find your model in the list (for example, WalkingPad). R2) And follow the instructions on the screen.

If the device is not located:

• 🔄 Reboot the router and treadmill.
• 📶 Make sure your smartphone and track are connected to the same Wi-Fi network (2.4 GHz!).
• 🔋 Check that the track is plugged in and the indicator flashes on it (usually blue or green).
• 🛠️ Update the firmware of the Mi Home app to the latest version.

Important: Some models (e.g. KingSmith) K3) Pre-activation is required through QR-The code that's on the case under the protective film, and without scanning that code, the track won't be visible in the app.

4. Common mistakes and their solutions

If Xiaomi’s treadmill doesn’t turn on, the reasons can be both trivial and serious, and we’ve collected the most common problems and ways to fix them:

Pay special attention to the error code if it is displayed on the display, for example:

• E1 — Engine problem (service required).
• E2 — Control board malfunction (try resetting settings).
• E3 — Speed sensor error (check the optical sensor's purity).

⚠️ Warning: If the track begins to vibrate or make uncharacteristic sounds after a fall or impact, immediately disconnect it from the network. This may be a sign of damage to the frame or engine, which is dangerous for further operation.

5. Resetting to factory settings: when necessary

If Xiaomi’s treadmill is glitchy (it changes speed, doesn’t save settings, or connects to an app), resetting to factory settings will help, which removes all user data, including training and calibration histories.

Instructions for discharge:

1. Turn off the track.
2. Press and hold the Power button (or Reset, if any).
3. Without releasing the button, connect the power.
4. Hold for another 10-15 seconds until the indicator blinks.
5. Release the button and wait for the reboot (can take up to 1 minute).

For models with touch screen (KingSmith) R2 Pro):

1. Go to Settings → System → Reset.
2. Enter a confirmation code (usually 1234 or 0000).
3. Confirm the action on the screen.

⚠️ Warning: After the reset, you may need to re-assign to your Mi Home account. If the track does not connect to Wi-Fi, check if the password from the network has changed.

💡

Resetting is a last resort. Before you make a hard reset, try restarting the device (remove the plug for 30 seconds) or updating the firmware through Mi Home.

6.Firmware Update: Why It Matters and How to Do It

The manufacturer regularly releases updates to Xiaomi treadmills that fix bugs, add new training regimes and improve compatibility with other devices in the ecosystem.

• 🐢 Slow-motion response to remote commands.
• 📵 Loss of communication with the Mi Home app.
• 🔄 Spontaneous reboots during training.

To update the firmware:

1. Open the Mi Home app and select your treadmill.
2. Go to the Settings section (cog in the upper right corner).
3. Click on “Firmware Update” (Firmware Update).
4. If a new version is available, click “Update”.
5. Do not disconnect the track from the network until the process is complete (it can take up to 10 minutes).

If the update is hanging:

• Reboot the router and track.
• Check that the smartphone is enabled mobile Internet (in case of a Wi-Fi break).
• Try upgrading from another device (such as a tablet).

7.Inclusion after long downtime: nuances

If the Xiaomi treadmill stood idle for more than a month, follow several mandatory steps before turning on:

1. Check the belt lubrication. It might have dried during the idle time. Apply 1-2 ml of silicone lubrication on the side under the belt.
2. Check the belt for cracks. If there is damage, replace it (parts can be ordered on the official website).
3. Call the power cable, mice or pets could have damaged the insulation.
4. Update the firmware. Critical security patches may have been released during the downtime.

When first switched on after a downtime track may:

• 🔄 Automatically start calibration (do not interrupt the process!).
• 📛 Showing a mistake E4 (lubrication).
• 🔋 Discharge the built-in battery (if the model is portable, for example, WalkingPad) X21).

If the track smells like a burn when it is turned on:

⚠️ Warning: Disconnect it immediately from the grid and do not turn it on until a specialist has examined it, this may be a sign of a short circuit in the engine or control board!

FAQ: Frequent questions about including Xiaomi treadmills