How to properly connect Xiaomi Mi True Wireless Earbuds Basic 2 with your phone: detailed instructions

Xiaomi Mi True Wireless Earbuds Basic 2 headphones remain among the most popular budget headphones TWS-With a balanced sound, compact body and stable connection, users often have questions about how to use a device as simple as this. How to make the first connection correctly, what to do if the headphones are not determined by the phone, or how to reset the settings to the factory. In this article, we will discuss all the nuances of pairing Step-by-step, including rare problems that are not described in the official instructions.

The Mi True Wireless Earbuds Basic 2 features a Bluetooth 5.0 chip that offers low power consumption and a range of up to 10 meters without interference. But it's not just the pairing that matters to work properly, but the correct setting of codecs (such as AAC or SBC), the choice of sound profile and even the version of the headphone firmware. If you encounter interruptions or poor microphone quality, the reasons may lie in the wrong connection parameters.

1. Preparation of headphones for the first connection

Before you start pairing, make sure that the headphones Xiaomi Mi True Wireless Earbuds Basic 2 fully charged. the indicator on the case charge case should be lit green (charge ≥80%) or orange (30-80%). If the indicator flashes red – connect the case to the power source for 30-40 minutes.

Also check:

• 🔋 Charge headphones inside the case: pull them out, each should flash a white indicator (means enough charge). If the indicator is red, put the headphones back in the case for 10-15 minutes.
• 📱 Bluetooth version on your phone: Mi True Wireless Earbuds Basic 2 requires Bluetooth 4.2 or later. On Android, check in Settings → The phone. → Information on the PO.
• 🔄 No old connections: if the headphones were already paired with another device, they must be reset (instruction in section 5).

⚠️ Note: If the indicator on the case does not respond to the cable connection, try another one. USB-Xiaomi Mi True Wireless Earbuds Basic 2 sensitive to unstable voltage – use original or certified cable USB-A/USB-C.

For the first inclusion:

1. Take both headphones out of the case - they will automatically turn on and go into pairing mode (indicators will flash red and white).
2. If the lights don’t flash, press and hold the touchpad on any headphone for 5 seconds until you hear the beep.

2. Interfacing with Android-smartphone (Step-by-step)

On Android, the connection process is as simple as possible, but there are nuances for Xiaomi, Samsung and other brands.

1. Open Settings → Bluetooth on your phone and activate the module.
2. In the list of available devices, find Mi True Wireless Earbuds Basic 2 (It can be displayed as Mi True Wireless or LE_Basic_2).

On Xiaomi smartphones (MIUI 12 and later), after connecting, a window will automatically open with a suggestion to install the Mi Earphones branded application. Its installation is not mandatory, but it is recommended for:

• 🎛️ Equalizer settings (bass/medium/upper frequencies).
• 🔋 Display the charge level of each headphone separately.
• 🔄 Firmware updates (if available for your model).

⚠️ Note: On some Samsung phones (such as the Galaxy A series or the Samsung phone). S21) There may be a problem with one-way sound, it's a codec conflict. Solution: in Bluetooth settings, select a headphone profile. AAC instead SBC.

If the headphones are connected, but the sound is interrupted:

Make sure the distance to the phone is ≤5 meters |

Turn off Wi-Fi (5GHz may cause interference)|

Close background applications using Bluetooth|

Reboot your phone and headphones (put in the case for 10 seconds)-->

3. iPhone (iOS) interface and features

On iPhone (iOS 12 and later), Xiaomi Mi True Wireless Earbuds Basic 2 connects standardly, but there are limitations:

• 🍎 No support for Mi Earphones (only basic features available).
• 🔊 Sound quality may be worse than Android due to forced codec use AAC (Android can be selected SBC or aptX on supported devices).
• 📱 No display of the headphone charge level in the status bar (only the total charge of the case).

Instructions for iPhone:

1. Open Settings → Bluetooth.
2. Get the headphones out of the case - they will appear on the list as Mi True Wireless.
3. Click "Connect" and wait for the "Connected" sign to appear.

If the headphones are not defined:

• 🔄 Reboot your iPhone and try again.
• 📱 Forget the device in Bluetooth settings (if it was already there) and pair again.
• 🔋 Check the case charge – on iOS, headphones may not appear if the charge level is below 20%.

💡

On iPhone, to improve sound quality, disable the “Low Data Quality” function in mobile settings (Cellular Communication → Data Parameters → Data Mode).

4. Connect to a laptop or PC (Windows/macOS)

The interface to the computer has its own nuances. On Windows 10/11:

1. Open Settings → Devices → Bluetooth and other devices.
2. Press "Add device" → Bluetooth.
3. Select Mi True Wireless Earbuds Basic 2 from the list.
4. After connecting in the Audio section, select the headphones as the Default device.

On macOS:

1. Open System settings → Bluetooth.
2. Click "Connect" next to Mi True Wireless.
3. In System settings → Sound, select headphones to output sound.

Common problems on PCs:

5. Resetting headphones to factory settings

If Xiaomi Mi True Wireless Earbuds Basic 2 is not connected, is unstable or “glut”, perform hard reset. This will delete all saved connections and return the default settings.

Instructions:

1. Put both headphones in the charging case and close the lid.
2. Open the lid and hold the touch panels on both headphones for 15 seconds.
3. The indicators on the headphones will start flashing red, then white - this is a signal of a successful reset.
4. Close the case cover for 5 seconds, then repeat pairing with the phone.

⚠️ Note: After reset, headphones may be temporarily defined as LE_Basic_2 It's okay, because when you first connect, the name goes back to the original name.

If the dumping didn't help:

• 🔌 Try charging the case with another cable (possibly contact problem).
• 📱 Install the Mi Earphones app and check for the availability of the firmware update.
• 🔧 Contact the service center if the indicators do not respond to the reset.

Adjustment of sound and microphone

By default, Mi True Wireless Earbuds Basic 2 uses a sound balance focused on vocals and medium frequencies.

• 🎵 In the Mi Earphones app, select one of the preset equalizers: Bass, Bright or Natural.
• 🎤 To improve the quality of the microphone, turn off noise cancellation in call settings (on Android: Settings) → System system → Sound. → Quality of calls).
• 🔊 On iPhone, activate Transparency mode in the control panel to hear ambient sounds during a conversation.

A critical feature of the model: the microphone works only on the right earpiece. If the person does not hear you during the call, make sure that the right earpiece is in the ear and not covered with hair or scarf.

To test the microphone:

1. Open the Dictaphone app on your phone.
2. Start recording and say a few phrases.
3. Listen to the recording – if the voice sounds muffled, clean the microphone hole on the right earpiece (use a dry soft brush).

💡

For maximum audio quality on Android, use codecs in order of priority: aptX (if supported), AAC, SBC. On iPhone, only AAC is available.

7. Solving common problems

Even after successful pairing, users face typical problems. Consider the most common:

If the headphones are not on:

1. Place them in the case for 30 minutes (even if the indicator is not on).
2. Try charging the case from another source (e.g. power bank).
3. If the indicators do not respond, reset (section 5) or contact the service.

Frequently Asked Questions (FAQ)