Xiaomi Earbuds Basic 2 Reset Fully Solves Connection Issues

Modern wireless headphones, such as the Xiaomi Earbuds Basic 2, are miniature computers running a specialized operating system. Over time, errors can accumulate in the headset software caused by left-right channel desynchronization or Bluetooth protocol failures when switching between devices. Users often face a situation where one of the headphones stops playing sound or the device disappears altogether from the list of available for pairing.

In such cases, standard power outages don't help, because it requires a deep cleaning of the internal memory of the settings. A procedure known as hard resets returns the gadget to factory status by removing all temporary files and old connection profiles, and this is the most effective method of eliminating software glitches without having to go to a service center.

This operation takes only a few minutes, but requires precise follow-up. Incorrect pressing order can cause the headphones to not enter pairing mode or remain in a state of desynchronization. Carefully read the instructions before you start manipulating to ensure a positive result on the first attempt.

When you need to complete the resetting of the settings

There are a number of specific symptoms that indicate that you need to immediately intervene in the operation of the device. If you notice that the indicators are lit in different colors or flashing at different frequencies, this is a sure sign of channel desynchronization, and also an alarm is a situation when the phone sees only one headphone from a pair, ignoring the second.

Another common problem is the inability to complete pairing: The phone can give out a connection error or simply search the device endlessly even if it is in close proximity. In some cases, removing the profile from Bluetooth settings helps, but if the problem comes back, a more radical approach is required.

⚠️ Warning: If the headphones make intermittent sound or constantly lose communication when fully charged, this may indicate a software conflict that is solved only by a complete reset.

Sometimes users find that voice prompts sound incorrect or in Chinese instead of English. Resetting often helps to switch the language pack to the correct one if the device was purchased in another country.

It's important to understand that the reset doesn't affect the physical state of the battery, but it restarts the power controller. If the problem was a charge level error, the display should be displayed correctly after the procedure, which is especially true for models that have been in use for more than a year.

Preparation for the discharge procedure

Before you start the action, you need to ensure that the right conditions for the operation are in place. First of all, make sure that there is enough energy left in the charging case. Although the reset process itself does not require much energy, the headphones should be able to turn on and enter standby mode.

It is crucial to remove the old pairing from your smartphone's memory. Go to Bluetooth settings, find Xiaomi Earbuds Basic 2 in the device list, and click "Forget this device" or "Delete." This will prevent the phone from automatically connecting to the headphones during setup, which could interrupt the process.

It is also recommended to wipe the contact areas on the headphones themselves and inside the case with dry soft cloth. Oxidation of the contacts can cause one of the headphones to not charge and turn on at the right time.

Put both earbuds in the case and close the lid. Let them lie closed for about 10 seconds, which is necessary for them to go into sleep mode and prepare to receive a reset command. Don't ignore this step, because it's critical to the stability of the controller.

How to Reset Xiaomi Earbuds Basic 2

The process of resetting this model differs from the newer versions by the absence of a physical button on the case. All control is carried out exclusively through the touch zones on the headphones themselves. You will need to perform a series of accurate presses, observing time intervals.

Take both earbuds out of the charge case. They should automatically turn on. If the lights don't catch fire, press and hold the touchpads on both earbuds simultaneously for 5 seconds until they flash red. They're ready to reset.

Put the headphones back in the case, but don't close the lid. Quickly press 5 times on the right earphone touchpad, then 5 times on the left. Some instructions recommend doing this simultaneously, but in practice it is safer to press 5 times on the right, then 5 times on the left, fitting in 2-3 seconds.

Sequence of action:


1. Get the headphones out.




2. Turn off (hold 5 seconds)




Insert (retention 5 seconds)




4. Put it in the case.




5. 5 taps right + 5 taps left

After a series of taps, the headphones should flash red three times, signaling that the pairing memory is cleared and the devices are reset, and then you need to take them out of the case again, and they should go into automatic pairing mode (blinking white).

⚠️ Attention: If nothing happened after 5 taps, you may have been acting too slowly.

The process of re-pairing with the phone

After a successful reset, the headphones go into a pairing mode, the indicators will flash white, which means they are ready to connect, at which point you need to turn on Bluetooth on your smartphone and start looking for new devices.

The list of available devices should be called Mi True Wireless EBs Basic 2 or similar. Click on it to connect. If everything goes well, you will hear a voice confirmation or a characteristic beep, and the indicators on the headphones will go out or light up with a flat light.

In some cases, the phone may request permission to access contacts or call logs, which is a standard Bluetooth feature for displaying the caller's name. You can either agree or refuse, and the sound quality will not be affected, but the main thing is that the connection status is changed to "Connected".

💡

If the phone sees two devices with the same name, choose the one that appeared first, or delete both profiles and start searching again.

Check both channels. Turn on the music and make sure the sound is on both the left and right. Also, check the microphone by recording a short voice message. If the sound is monophonic or one channel is missing, you will have to repeat the reset procedure.

Common Errors and How to Resolve Them

Even when you follow the instructions, you sometimes have a problem, and one of the common problems is that the headphones don't reset the first time, and this can be due to battery drain or too fast to do something, and try to completely discharge the case and the headphones, then charge them to 100% and try again.

Another common mistake is to desynchronize after reset. If one earphone flashes and the other doesn't, put both in the case, close the lid, wait 10 seconds and pull out at the same time. If that doesn't work, reset again, but this time press the touchpads at a smaller interval.

If neither method works, it may be a hardware problem, a Bluetooth module or a battery could fail, and then the software methods are powerless, and a diagnostic at a service center is required.

💡

Successful reset is confirmed by triple flashing of the red indicator and switching to white blinking mode (search for the device).

Care and prevention of problems with TWS headphones

To avoid the need for frequent resets and extend the life of your Xiaomi Earbuds Basic 2, you should follow simple rules of operation. Do not allow a deep battery discharge. If you do not plan to use headphones for a long time, charge them at least once every three months.

Clean the speaker mesh regularly of earwax and dust. Clogged holes can create the illusion of a quiet sound or its complete absence, which users mistakenly mistake for a software glitch. Use a soft brush or dry toothbrush for cleaning.

Try not to drop the case or the headphones themselves. The impacts can damage the internal contacts or quartz crystals that are responsible for frequency synchronization. Even a microcrack in the board can lead to unstable Bluetooth connection.

⚠️ Warning: Do not use headphones in high humidity or rain.The Basic 2 model has basic sweat protection but is not waterproof.

Following these guidelines will help keep the device stable throughout its life. Remember that electronics do not like extreme temperatures, so do not leave the gadget in the sun or in the cold.

Frequently Asked Questions (FAQ)