How to use Xiaomi irrigator: instructions with dental advice

Xiaomi irrigators are smart devices that have revolutionized oral care, not just replacing dental floss, but providing professional home cleaning, removing up to 99.9 percent of plaque in hard-to-reach areas, but for the irrigator to last long and bring maximum benefit, you need to know the nuances of its use, from the first setup to daily care.

In this article, we will analyze all the stages of working with Xiaomi irrigators (Oclean models). W10, Xiaomi Mijia, Soocas H3 Others, including device preparation, mode selection, cleaning techniques and typical user errors, will focus on unique firmware features. MIUI For irrigators, which often go unnoticed, if you're just buying a device or want to improve your skills, this is the guide for you.

Preparing Xiaomi irrigator for the first use

Before you start, you need to assemble the irrigator properly and set it up. Start by unpacking, and you'll find the device, the nozzles (usually) in the kit. 2-4 Charging cable (USB-Type-C or wireless station), instruction in Chinese and power adapter (if provided for your model).

Important point: Oclean models W10 Soocas H3 There's a protective film on a water tank in the box, which you have to remove before it's first filled, or the pump can clog, and you also have to check if the tank lid is tightly twisted, and if it's not tightly attached, it will leak when you're running.

• 🔋 Charge before first use. Connect the irrigator to the network 4-6 A full charge cycle extends battery life. In wireless charging models (e.g. Oclean X Pro Elite), use only the original station.
• 💧 Flush the system, put some warm water in the tank (30-35°C) and switch the device on 1-2 - No nozzle for minutes to clear the internal tubes of the factory lubrication. 2 once.
• 🔧 Install the nozzle. Put the nozzle on the holder before clicking. For models with magnetic mounting (for example, Soocas). W3) Make sure the contacts match - otherwise the jet will be weak.

After preparation, turn on the irrigator power button and select mode (more on this in the next section).If the device does not respond to presses, check if the baby lock is activated - it is on most Xiaomi models and is enabled by holding the Mode button for a long time.

What to choose for your teeth: which ones to choose?

Xiaomi Irrigators Are Equipped 3-5 The modes of operation that differ in jet intensity and pulse frequency depend on the condition of your gums, the sensitivity of your teeth and the purpose of cleaning):

For most users, Normal is the optimal mode, which is powerful enough to remove plaque, but does not injure the gums. If you are just starting to use an irrigator, start with Soft and gradually increase the pressure. 1-2 once a week, as it can cause gum bleeding when used regularly.

Dentist's advice: If you have crowns or veneers installed, avoid directing the jet directly to the edge of the gums - this can lead to bare neck of the tooth over time — 60-90 degree.

💡

In Oclean models W10 Soocas H3 You can save your favorite mode in the device's memory. To do this, hold the mode button for 3 seconds, the irrigator will give an audible signal confirming the preservation of the device.

Step-by-step technique of brushing teeth with an irrigator

The correct technique of using the irrigator guarantees maximum efficiency and prevents damage to the gums.

1. Preparation. Brush and floss your teeth (if you use them) and fill the irrigator tank with warm water (35-40°C) or rinse. For models with function UV-sterilization (e.g., Soocas) W3) Turn it on for 5 minutes before use.
2. Pressure setting. Start at the minimum level and gradually increase it to the comfort level. Use Soft mode for the first time.
3. Positioning the nozzle. Hold the irrigator at an angle. 90 degrees to the tooth, at a distance 2-3 The nozzle should be aimed at the pocket between the tooth and the gums, not at the gums themselves.
4. Start with the back teeth of the upper jaw, then move to the front and finish with the lower jaw. 2-3 seconds.
5. Rinse. After cleaning, rinse your mouth with water or rinse. Turn off the irrigator and drain the remaining water from the tank.

A critical error: many users point the jet directly at the gums, which leads to injury, and that is right, to handle the interdental spaces by moving along the gum line, rather than perpendicular to it.

Start with minimal pressure.|Don't direct the jet directly at the gums.|Hold the nozzle at an angle. 60-90°|Do not use boiling water or ice water.|After cleaning, wash the tank.-->

For brace or implant owners, the technique is slightly different:

• 🦷 Braces: Use Orthodontic nozzle (if included) and Turbo mode. Direct the jet from top to bottom for upper jaw and bottom to bottom for lower jaw.
• 🦷 Implants: avoid Pulse mode - it can loosen the crown. Use Normal with reduced pressure (up to 500 kPa).

Irrigator care: how to extend the service life?

Xiaomi's irrigator will last years if you follow simple maintenance rules. The main problems users have -- mold in the tank and clogging of the nozzles -- are caused by improper drying and storage. Here's a care checklist:

• 🚿 Rinse after each use. Wash the tank and nozzles with warm water, then dry them outdoors (not in a closed case!).
• 🧼 Deep cleaning 1 time per week.Pour vinegar solution (1:1 with water) or special irrigator remedy into the tank, turn on the device for 1 minute without nozzle, then rinse.
• 🔋 Battery storage. If you don't use an irrigator for longer than 2 weeks, drain the battery to 40% and store it in a cool place (not in the bathroom!). Full discharge or 100% charge reduces battery life.
• 🛠️ Replace the nozzles. Nozzles need to be changed every time. 3-6 Oclean models have a wear indicator, the blue stripe on the nozzle fades over time.

Warning: Never use abrasives (such as soda powder) to clean the tank - they will damage the inner coating and lead to corrosion. UV-lamp (Soocas) W3, Oclean X Pro is enough to include sterilization 1 time in 3 days.

⚠️ Warning: If the irrigator starts to make an uncharacteristic noise (squeaking or vibration), immediately turn it off and check if a foreign object has entered.

For models that support the Mi Home app (e.g. Oclean) W10) It's a self-diagnosis function that's available to start:

1. Open the app and select your irrigator.
2. Go to Settings. → Diagnostics.
3. Press Launch Check.

The app will show the pump, the battery and the tank's tightness if there's an error. E2 — This is a signal about a clogged filter (you need to wash it under the water stream).

Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes that reduce the efficiency of the irrigator or lead to its failure.-5 lapses and ways of correcting them:

• 🚫 Use boiling water. Hot water (above) 50°C) deforms the plastic of the reservoir and may damage the sealing rings — 35-40°C.
• 🚫 Storage with water in a tank. The remaining water becomes a breeding ground for bacteria. Always drain the residue and dry the tank.
• 🚫 The jet's direction is perpendicular to the gums, which injures tissues and can cause bleeding. 60-90 degree.
• 🚫 Ignoring replacement nozzles. Worn nozzles lose their effectiveness and can scratch enamel. Change them every time. 3-6 months.
• 🚫 Charging with a non-original cable, which can cause the battery to overheat. 5V/1A or 5V/2A.

Another common problem is low water pressure, and there are many reasons.

If the irrigator Xiaomi stopped holding the charge (discharges for the battery) 1-2 Use, try calibrating the battery:

1. Completely discharge the device (until automatically shut down).
2. Connect to charging and hold for 12 hours without a break.
3. Repeat the discharge/charging cycle 2 times.

This method restores up to 80% of capacity in 70% of cases (data from Xiaomi service centers).

Compatibility with rinses and liquids

Can you put a rinse in a Xiaomi irrigator instead of water? Yes, but not any. Majority models (e.g. Oclean) W10, Soocas H3) They're compatible with liquids labeled "irrigators." Normal oral rinses like Listerine can't be used, they contain alcohol and oils that spoil seals and pumps.

Here is a list of proven liquids for Xiaomi irrigators:

• 💧 Oclean Effervescent Tablets - tablets for preparing a solution (elimine plaque and refresh breathing).
• 💧 Soocas Oral Cleaner - antibacterial solution with xylitol.
• 💧 Waterpik Water Flosser Solution – a universal rinse for all types of irrigators.
• 💧 Homemade solution: 1 tsp salt + 1 tsp. soda per 200 ml of water (1 time per week for disinfection).

Important: After using the rinse, always rinse the tank with clean water to avoid corrosion of metal parts. In models with ion technology (Oclean X Pro), you can only use distilled water - conventional tap water reduces the life of the ion rod.

⚠️ Warning: If you use a chlorhexidine rinse, do not exceed a concentration of 0.05%.Higher doses can cause burns to the mucosa and damage plastic parts of the irrigator.

For owners of models with aromatherapy function (Soocas) W3) water-injectable 1-2 drops of essential oil (for example, mint or tea tree), but only if it is 100% natural and does not contain synthetic additives.

Integration with Xiaomi ecosystem: smart features

Xiaomi irrigators (especially Oclean and Soocas models) support integration with the Mi Home ecosystem, which opens up additional opportunities for:

• 📱 Control through the app. Mi Home is available:
• 🔄 Sync with other devices, for example, the irrigator can automatically turn on after you brush your teeth with Xiaomi’s electric brush (if both devices are connected to the same Mi Account).
• 🔋 Smart charging. The app shows the exact percentage of charge and battery life. There is also a function Fast charging - 10 minutes to charge is enough for 1 complete cleaning.

To connect the irrigator to the Mi Home:

1. Install the Mi Home app (available for Android and iOS).
2. Sign up or sign in to your Xiaomi account.
3. Click Add Add the device (+) → Choose the Health category → irrigator.
4. Turn on the irrigator and hold the power button for 5 seconds until the indicator blinks.
5. Confirm the connection in the application.

After connecting, we recommend activating the following functions:

• 🔔 Reminder of cleaning (in the Settings section) → Notifications).
• 📊 Performance analysis (shows which areas of your mouth you miss).
• 🔄 Auto-update firmware (important for Oclean models) W10 newer).

Hidden function: In Oclean models with firmware 1.5.6+ There's an undocumented "Deep Clean" mode to activate it:

1. Turn on the irrigator.
2. Press the Mode button 3 times in a row.
3. Hold it for 2 seconds and you will hear a double beep.

This mode increases the pressure to 1000 kPa and includes a pulsating jet to remove the old plaque. Use it no more than 1 time a week.

💡

Connecting to the Mi Home offers access to advanced statistics, customization and automatic sync with other Xiaomi devices, especially for family use, where each family member can be assigned a personal profile.

FAQ: Answers to Frequent Questions