How to wear Xiaomi Mi wireless headphones: the secrets of comfort and safety

Xiaomi Mi wireless headphones (AirDots, Air 2, Air 3, Buds 4, etc.) have become an integral part of the daily lives of millions of users, but even such compact devices require proper handling — especially when it comes to wearing them. Improper landing in the ear canal can lead not only to discomfort, but also to deterioration of sound quality, rapid battery discharge or even loss of one of the headphones while driving.

In this article, we will take a step-by-step guide to how to wear Xiaomi Mi Wireless Earbuds, tell you about the size of the earbuds, explain how to check the tightness of the fit, and give tips for long wear without fatigue. We will pay special attention to common mistakes that even experienced users make, and tell you how to avoid them. If you just bought new headphones or have been using them for a long time, but feel that “something is wrong” – this guide is for you.

Why is it important to wear wireless headphones?

It seems like it's easy to put headphones in your ears, but in practice, a wrong fit leads to a whole host of problems.

• 🔊 Poor sound quality: bass is “lost”, high frequencies become sharp, and noise cancellation works inefficiently.
• 🔋 Fast discharge: if the headphone does not fit tightly, the microphone and motion sensors work harder, consuming charge.
• 😖 Wearing discomfort: Pressure on the ear or cartilage can cause headaches in 30 to 60 minutes.
• 🏃 Loss while driving: especially relevant for running, exercising or cycling.

Moreover, the Xiaomi Mi Earbuds are equipped with infrared sensors that determine whether the headphones are wearing. If the landing is wrong, the sensor can falsely fire, interrupting music playback or turning off the microphone during a call. ANC (Active Noise Cancelling – leaky fit negates the entire effect of noise reduction.

And we've shown that even people who wear headphones for years often don't know they're doing it wrong, and then we'll take a step-by-step algorithm to help avoid all of these problems.

Preparing headphones for the first use

Before you wear Xiaomi Mi Wireless Earbuds, you need to prepare them properly, which is especially important if you have just unpacked the device or have not used it in a long time.

⚠️ Note: If the headphones were stored at a temperature below 0°C or higher than 40°C, before use, allow them to warm up to room temperature for 1-2 hours.

Step 1. Check the complete setup.

In the box with headphones should be:

• 🎧 The headphones themselves (left and right, often marked with the letters L and R).
• 🔋 Charging case (with charge indicator).
• 🔄 Set of replacement embushures (usually 3 sizes: S, M, L).
• 📑 Short instructions (sometimes with a QR-code-driven full guide).
• 🔌 Charging cable (in newer models often) USB-C).

Step 2. Charge the headphones.

Even if the indicator on the case shows a charge, before the first use, it is recommended to fully charge the device. Connect the case to the power source (it is better to use the original cable) and wait until all LEDs light up green. In Mi Air 2 Pro models and later charging up to 100% takes about 1.5 hours.

Step 3: Update the firmware (if necessary)

Outdated software can cause problems with connection or sensors, to check the relevance of the firmware:

1. Connect the headphones to the smartphone via Bluetooth.
2. Open the Mi Home or Xiaomi Earbuds app (depending on the model).
3. Go to the Device Settings section → Update of the PO.
4. If you have a new version, follow the on-screen instructions.

How to choose the right size of ambushes

Ambushes (or "inlays") are silicone nozzles that ensure a tight fit of the earpiece to the ear canal. Complete with Xiaomi Mi Earbuds, there are usually 3 sizes: S (Small), M (Medium) and L (Large), the right choice of size is the key to comfort and quality sound.

How do you determine your size?

The most reliable way is to try all the options one by one, but there are indirect signs.

• 👂 If the M is too loose and the earpiece falls out with a slight shake of the head, try the size L.
• 😫 If after 20-30 minutes of wearing there is pressure or pain - the bulge is too large, try S.
• 🔊 If the bass "disappears" and extraneous noises are heard - the embusheries are too small, there is no tightness.

Pressure test

To check if the slacks are sitting correctly:

1. Put on your headphones and turn on the music at medium volume.
2. Close the ear canal with your finger (without pressing the earpiece!).
3. If the sound is noticeably quieter, the earpiece is right. If it doesn't make any difference, try a different size.

In the Mi Air 3 Pro and Mi Buds 4, the earpieces are asymmetrical for better fit. Note the L and R tags, which should match the markings on the headphones themselves.

How to wear Xiaomi Mi Wireless Earbuds

Now, to the most important thing, the putting algorithm, follow these steps to achieve the perfect fit.

Step 1. Identify left and right earphone

On the body of each headphone there is a marking:

• L is left.
• R is right.

In the Mi Air models 2S and newer marking can be engraved on the inside or illuminated by an LED when connected.

Step 2. Take the earphone correctly

Hold the earpiece by the body, not the earpiece, so you don't deform the silicone or break the tightness. The thumb should be on the touchpad (if there is one), and the index finger should be supported from the bottom.

Step 3. Turn the ears around.

Carefully pull the earlobe down and back, and it opens the ear canal for a deeper and tighter entrance of the earpiece, which is especially important for models with a high-performance earlobe. ANC, where the tightness is critical.

Step 4. Put the earphone in at an angle.

Don't try to put the earpiece straight, it's a common mistake! The right angle of entry is 15 to 20 degrees forward (as if you were pointing it toward the nose). Once the earpiece enters the ear canal, scroll the earpiece back slightly so that it sits tightly.

Step 5. Check the landing.

With a light movement, pull the earphone down -- if it doesn't move, it's the right fit. Repeat the procedure for the second earpiece.

Step 6: Set the position for maximum comfort

After both earbuds are on, move your jaw slightly (such as zegnite teeth or smile). If you feel pressure, try pulling the earbuds out a little or picking up a different size.

💡

If your headphones are constantly falling out while running, try putting them backwards (changing the L and R places), which is a non-standard technique, but it helps with the atypical shape of the ear.

Common Mistakes and How to Avoid Them

Even experienced users sometimes make mistakes when wearing Xiaomi Mi Earbuds, and here are the most common ones and ways to fix them:

Critical: In models with a wear sensor (for example, Mi Air 3 Pro) an incorrect landing can lead to false positives – the headphones will constantly “think” that they have been removed, and stop playback.

⚠️ Warning: If you still feel uncomfortable after wearing it properly, check if you have any dirt or earwax on the earpiece.

How to wear Xiaomi Mi Earbuds for a long time without fatigue

Even perfectly matched headphones can cause fatigue when worn for long periods of time, and here are some tips to make use of them more comfortable:

• 🕒 Keep the wear regimen optimally 1.5-2 hours of use, then 10-15 minutes of break.
• 🧴 Use a moisturizer: If the skin of the ears is prone to dryness, apply a thin layer of hypoallergenic cream before putting on.
• 🔄 Alternate earbuds: If you have nozzles of different materials (silicone/penomeri), change them depending on the activity (for example, foam is better for sports).
• 🎵 Control volume: sound above 60% of the maximum fatigues not only hearing, but also ear muscles, which increases discomfort.

For models with ANC (For example, Mi Air 3 Pro If you feel "stuffy" in your ears, turn off ANC 5-10 minutes or switch to Transparency mode (transparency).

If you wear headphones while sleeping (which is not recommended), choose models with ultra-soft earpieces (such as Mi Buds 4) and make sure the cable does not clamp the ear.

Features of wearing for different models Xiaomi Mi

While the principle of wearing the Xiaomi Mi Earbuds is similar, some models have unique nuances.

Mi AirDots (1-e) and Mi Air 2/2S

These models have round mounts without the wings fixing, and the problem is that they often fall out when you move abruptly.

• Use size L earpieces, even if M seems appropriate.
• Before insertion, warm the earpieces in your hands - silicone will become softer and tighter to cover the ear.

Mi Air 3 / Air 3 Pro

And there were oval embroideries and improved ergonomics.

• Headphones support ANC, So tightness is critical - always do a fit test.
• The touchpad is larger than previous models – do not touch it when you wear it to avoid false positives.

Mi Buds 4

The newest model at the time of 2026 with a semi-open design, the embushures are softer but less sealed:

• Not suitable for noisy places (metro, plane) due to weak ANC.
• Ideal for long-term wear – pressure on the ear is minimal.

Mi True Wireless Earbuds Basic 2

It's a low-end model with a minimalist design, and one common problem is that one earphone is less connected than the other.

• Before putting on, reset the settings through Forget the device in the Bluetooth settings of the smartphone.
• Put on the right headphone first (it is the main one in this model), then the left one.

💡

In wear detection models, headphones automatically stop music if you remove at least one of them. If the function is not working correctly, check the density of the fitting of the bulge.

What to do if the headphones are uncomfortable?

If you've tried all the tips, but Xiaomi Mi Earbuds are still uncomfortable, maybe the problem lies deeper.

1. Check the shape of the ear canal

In some people, the ear canals are non-standard (for example, too curved or narrow).

• 🛒 Buy third-party bottles (such as Comply Foam or SpinFit) that are better adapted to anatomy.
• 🩺 Contact ENT-y - sometimes discomfort is associated with medical features (for example, exostosis).

2. Try alternative ways of wearing

Some users wear Mi Earbuds backwards (turning the L and R) if the standard fit doesn't fit, and you can also experiment with the angle of entry, such as pointing the earphone to the back of the head rather than the nose.

3.Tune the sound balance

Sometimes the discomfort is not due to physical landing, but to sound pressure. In the Mi Home or Xiaomi Earbuds app, you can reduce the level of low frequencies (EQ-settings), which will reduce the load on the eardrums.

4. Check the sensor setup

In wear detection models (such as the Air 3 Pro), oversensitive sensors can cause irritation.

⚠️ Warning: If you notice itching, redness, or swelling in your ear canal after using your headphones, stop wearing them immediately and see your doctor.This may be an allergic reaction to the material of the earbuds (most often silicone).

FAQ: Answers to Frequent Questions