Xiaomi Mi True Wireless headphones (and their modifications: Mi True Wireless Earphones) 2/2S/SE/Basic) They became one of the most popular TWS-But even with these simple gadgets, users often have questions about how to sync them to a phone, why a single earbud doesn't connect, or how to reset them to factory settings. This article will help you understand all the nuances - from basic pairing to solving non-standard problems.
We will look at the official ways to connect to smartphones on Android (including devices Xiaomi/Redmi/POCO) and iOS (iPhone/iPad), and give recommendations for optimizing the work of the headphones. If you encounter an error “Device not found” or headphones refuse to sync with each other, here you will find proven solutions.
1. Preparation of headphones Xiaomi Mi True Wireless to connect
Before you pair it, make sure that the Mi True Wireless headphones are charged and searchable.
- 🔋 Case Charging: Connect the Case to the Power Source (USB-C Or wireless charging if supported, and wait for the full charge indication. 2S And the newer case charge takes up ~1.5 hours.
- 🎧 Headphone Removal: Take both earbuds out of the case - they should automatically turn on.If this does not happen, press and hold the touchpad on each earbud for 3 seconds.
- 🔍 Pair mode: The headphones go into search mode automatically when you first turn on. If they have already been connected to another device, reset (instruction in section 5).
Pay attention to the indicators of the state:
- 🟢 Green flashing - headphones in pairing mode.
- 🔴 Red – Low charge (less than 20%).
- 🟡 Yellow (on some models) – connection error.
💡
If the headphones don’t respond to touch, clean the touch panels with a dry wipe – contamination can block control.
For Mi True Wireless Earphones Basic models (without touch control), use a mechanical button on the body: one short press is playback / pause, hold 2 seconds is on / off.
2. Connect to Android phone (including Xiaomi/Redmi/POCO)
The process of pairing with Android devices takes no more than 1 minute if the headphones are in search mode.
- Open the Settings. → Bluetooth on your phone and activate the adapter.
- In the list of available devices, find Mi True Wireless Earphones (or similar to your model name).
- Confirm pairing if you request access to contacts or microphone (not necessarily for music).
- Wait for the message "Connected." Now the headphones are ready to use.
On Xiaomi smartphones with the shell MIUI 12/13/14, after connecting, a pop-up will appear with a suggestion to install the branded Mi Earphones app (available on Google Play).
- 🎛 Set up an equalizer (presets Basic boost, Pure vocals, etc.).
- 🔄 Update the firmware headphones (relevant to Mi True Wireless) 2S newer).
- 📊 View the charge level of each headphone and case.
Headphones are displayed in the list of Bluetooth devices |The sound is played synchronously in both headphones |The indicator on the case is burning green |The Mi Earphones app recognizes the model
-->
Important: Xiaomi Mi True Wireless headphones support Bluetooth 5.0 protocol, but for a stable connection, it is recommended to use a phone with a Bluetooth version at least 4.2. On older devices (for example, Redmi 4A), problems with synchronizing stereo sound may occur.
3. Connection to iPhone or iPad (iOS)
While Xiaomi is a brand with a focus on the Android ecosystem, Mi True Wireless headphones are fully compatible with Apple devices (iPhone 6s and newer, iPad with iOS 10+).
- Go to Settings → Bluetooth and turn on the adapter.
- Take the headphones out of the case and wait until they appear in the list of “Other devices” called Mi True Wireless.
- Click on the headphone name and wait for the inscription "Connected".
Features of working with iOS:
- 🍎 No support. AAC-Codec: iPhone will use the SBC (basic codec, which can slightly degrade the sound quality compared to Android.
- 📱 No proprietary app: Mi Earphones cannot be installed on iOS, so equalizer and firmware settings will not be available.
- 🔋 Charge Display: The headphone battery level will be visible in the Battery widget (scroll left on the home screen).
Android (Xiaomi/Redmi/POCO)|Android (another brand)|iOS (iPhone/iPad)|Other-->
If the headphones are connected but the sound is interrupted or interference is heard, try:
- Disable Wi-Fi while listening (2.4GHz network interference may affect Bluetooth).
- Close background apps that use a microphone (such as WhatsApp or Zoom).
- Reboot the headphones (put them in the case for 10 seconds, then pull out).
4. Solving Connection Problems
Even if you follow the instructions correctly, users sometimes encounter errors, and let's look at the most common problems and ways to fix them:
| Problem. | Possible cause | Decision |
|---|---|---|
| The headphones are not detected by the phone. | Headphones are not in pairing mode or discharged | Put the headphones in the case for 10 seconds, then pull it out. If it doesn't work, reset the settings (section 5). |
| Only one headphone is connected. | Failure of synchronization between headphones | Remove both headphones from the case, hold the touch panels for 15 seconds. until the indicator flashes twice. |
| The sound is interrupted or stuttered | Bluetooth interference or weak signal | Reduce the distance to your phone (max. 10 m), and turn off other Bluetooth devices. |
| The headphones are plugged in, but there's no sound. | Not selected sound source in settings | In the notification bar, select Mi True Wireless as the output device. |
If the problem persists, check:
- 📱 Bluetooth version on your phone: on Android, you can find it in Settings → The phone. → Bluetooth version.
- 🔄 Updates for Mi True Wireless 2S Check the relevance of the software through the Mi Earphones app.
- 🛠 Physical damage: inspect the case charging connector and headphone contacts for oxidation.
What if the headphones are connected, but immediately switched off?
Critical error: If the headphones stopped turning on after reset (the indicator does not burn), this may indicate damage to the controller. In this case, contact the Xiaomi service center - self-repair is impossible.
5.Reset Xiaomi Mi True Wireless settings to factory
If the headphones are unstable or do not connect to the new device, a complete reset will help.
For Mi True Wireless Earphones 2/2S/SE:
- Put both headphones in the case and close the lid.
- Open the lid and hold the touchpad on both headphones for 20 seconds.
- The indicator on the case will flash red → green (a signal of a successful reset).
For Mi True Wireless Earphones Basic:
- Take the headphones out of the case.
- Hold the mechanical button on each earphone for 10 seconds until the indicator starts flashing red and green alternately.
- Put the headphones back in the case for 5 seconds, then pull out - they will be in pairing mode.
After discharge:
- The headphones will forget all previously coupled devices.
- The factory firmware will return (if updated).
- Sensory control settings (for customized models) can be reset.
💡
Resetting is the last step before you go to the service, and if the headphones don't work after that, it's probably a hardware problem (a battery or Bluetooth module is damaged).
6. Sound and control optimization
To get the most out of listening, customize your headphones to your preferences. Here's what you can do:
On Android (via the Mi Earphone app):
- 🎵 Equalizer: Choose Preset (Rock, Pop, Classics) or create your profile.
- 🔊 Transparency mode: Activate to hear surrounding sounds without removing your headphones (useful outside).
- 🎧 Sensor settings: Reassign actions (e.g., double tapping to switch tracks).
On iOS (manual):
Since the company application is not available, use system settings:
- Open Settings → Bluetooth and click on the icon “i” next to Mi True Wireless.
- Turn on the “Use as a headset” option to improve call quality.
- Turn off Auto Switch if the headphones are connected arbitrarily to other devices.
For all models:
- 🔋 Saving Charge: Turn off your headphones when not in use (they automatically turn off after 5 minutes without connecting).
- 📶 Connection stability: Keep your phone in your pocket at chest level – this is the optimal area for a Bluetooth signal.
💡
To quickly switch from headphones to the phone speaker during a call, tap the volume icon in the top notification bar and select Dynamic.
7. Frequent Questions and Myths About Xiaomi Mi True Wireless
There are a lot of rumors around Xiaomi wireless headphones.
⚠️ Note: Some users claim that Mi True Wireless "does not work with iPhone" It's a myth - headphones are compatible with any device that supports Bluetooth 4.2+. Problems arise only due to outdated firmware or mechanical damage.
Question: Can I use one headphone separately?
Answer: Yes, but only in Mono mode. Take one earpiece out of the case, it automatically connects as a mono headset, and the other earpiece is turned off.
Question: Why do the headphones run out quickly?
Answer: Reasons:
- 🔊 Loudness higher 80% (optimally — 60-70%).
- 📶 Active use of microphone (calls, voice assistants).
- 🧲 Old lithium polymer batteries (life of life) ~300 charge cycles).
Question: How to check the originality of the headphones?
The original Mi True Wireless features:
- 📦 A box with a hologram and QR-code (checked through the mi.com/verify).
- 🔊 Clear "Mi True Wireless" on case and headphones (no typos).
- 🎵 High-quality sound without wheezing at maximum volume.