Connection Xiaomi Redmi Airdots: full instructions with photos and tips

Xiaomi Redmi Airdots wireless headphones (including Redmi Airdots S, Redmi Airdots models) 2, Redmi Airdots 3) They are one of the most popular budgets. TWS-It's a combination of price, sound quality and battery life, but many users have difficulty connecting first, especially when it comes to pairing with a new headphone.-Xiaomi In this article, we will analyze all possible scenarios: from basic settings to solving typical errors such as "earbuds are not located" or "sound is interrupted".

It is important to understand that the Redmi Airdots connection process is different from the standard procedure for headphones from other brands (e.g. AirPods or Sony). WF-1000XM4). There are nuances to this, from activating the pairing mode to the correct sequence of button pressing on the case, if you've used wired headphones or other devices before. TWS-We'll go through each step in detail, including the hidden reset function through a 15-second hold on a button on the case that's not written in the official manual.

This article is relevant for all versions of Redmi Airdots (2019-2026), including firmware with Bluetooth 5.0/5.2 support. If your model is released later than 2026, check compatibility with your smartphone in specifications - some new chips (for example, Qualcomm QCC3040) may require a phone software update.

1. Preparation of headphones for connection

Before you pair it, make sure that the Redmi Airdots headphones are fully charged and in the "start" state.

• 🔋 Check the case charge: the indicator on the front panel should burn white (charge) >50%) or red (charge) <30%). If the indicator does not glow, connect the case to the charging on 10–15 minute.
• 🎧 Get the headphones out of the case: they must automatically turn on (the red/white LED flashes on each headphone).If this does not happen, return them to the case and try again.
• 📱 Make sure your smartphone is Bluetooth enabled and other connected audio devices (columns, car system, etc.) are disabled.).

If the headphones have already been connected to another device, you need to reset them to the factory settings.

1. Place both headphones in the case and close the lid.
2. Press and hold the button on the case for 15 seconds until the indicator starts flashing red and white alternately.
3. Open the case cover - the headphones are now ready for a new pairing.

💡

If the indicator on the case flashes only red, it means battery discharge. Charge the case for at least 30 minutes before reset.

Note: Redmi Airdots headphones may be temporarily identified as "Mi True Wireless" or "LE_Xiaomi_BB" — It's okay. The main thing is that a new name appears on the list of available devices.

2. Step-by-step instruction: connecting to Android

The pairing with Android smartphones (including Xiaomi, Samsung, Realme, etc.) takes place through the standard Bluetooth menu. Let’s take the example of MIUI 14 and Android 13, but the steps will be identical for other versions.

Open Settings → Bluetooth| Turn on Bluetooth| Get your headphones out of the case | Select "Redmi Airdots" in the list | Confirm pairing-->

Detailed steps:

1. Activate Bluetooth on your smartphone: go to Settings → Connections → Bluetooth (or swipe down the notification bar and click the Bluetooth icon).
2. Remove the headphones from the case: they will automatically go into pairing mode (the indicators will flash alternately).If there is no blinking, press and hold the touchpad on the right earphone for 3 seconds.
3. In the list of available devices, find the item "Redmi Airdots" (or "Mi True Wireless" for older models).
4. Confirm pairing if you have a request. Some smartphones may need input PIN-code - default is 0000.
5. Wait for the "Connected" message. Now the headphones are ready to use.

If the headphones don’t appear on the list, try:

• 🔄 Reboot the Bluetooth module of the smartphone (disable/enable Bluetooth).
• 📴 Turn off and turn on the headphones again (place in the case for 10 seconds, then get out).
• 📱 Update your smartphone software – older versions of Android (below 10) may not support Bluetooth 5.0.

3. iPhone (iOS) connection and features

While Redmi Airdots are optimized for Android, they can also be connected to iPhones (iOS 12 and higher).

• 🍎 The iPhone will not display the charge level of headphones and case (unlike AirPods).
• 🎵 The dual-press function to control playback works differently (for example, you can’t configure Siri call).
• 🔊 Sound quality may be worse due to lack of codec support AAC fully (used) SBC).

Instructions for connection:

1. Open the settings → Bluetooth on the iPhone.
2. Take the headphones out of the case and wait until they appear on the list as "Redmi Airdots" or "LE_Xiaomi_BB".
3. Click on the device name and wait for the connection (can take up to 20 seconds).
4. If the connection does not occur, forget the device (Settings → Bluetooth → “i” next to the name → Forget this device) and try again.

To improve the sound on the iPhone, we recommend:

• 🎛 B Settings → Music. → EQ Choose a preset "Pop" or "Rock" (amplifies low frequencies).
• 🔊 Turn off "Reduce Loud Sounds" in Settings → Sounds and tactile signals → Headphone safety.

4. Problem Solving: Headphones don't connect

If Redmi Airdots are not detected by the device or are connected with errors, the reasons may be as follows:

One of the most common mistakes is the unsynchronized work of the headphones (for example, the right earphone connects, and the left one does not).

1. Place both headphones in the case and close the lid.
2. Take out only the right earpiece and wait 10 seconds (it should flash white).
3. Get the left earpiece – it should automatically sync with the right one (the indicators will light up at the same time).
4. Connect to the headphones via Bluetooth.

💡

If the headphones are discharged to zero, before the first connection after charging, be sure to reset (15-second hold of the button on the case).

If the problem persists, check:

• 🔋 The status of contacts in the case (clean them with a cotton swab dipped in alcohol).
• 📲 Compatibility of your smartphone with Bluetooth 5.0 (old phones may require software updates).
• 🔄 Try connecting the headphones to another device – if the problem recurs, a malfunction in the headphones themselves.

5. Control and sound setting

Once connected successfully, you can adjust the touch control and sound quality, and by default, Redmi Airdots supports the following gestures:

• 🎵 Double touch (on any headphone): playback / pause.
• 📞 Triple touch (on the right earphone): call voice assistant (Google Assistant)/Siri).
• 🔊 Holding 1 second (left earphone): move to the next track; right – return to the previous one.

To change the purpose of gestures (for example, configure the last number or turn off noise cancellation), use the official Mi Home app:

1. Download Mi Home from Google Play or App Store.
2. Sign up or sign in to your Xiaomi account.
3. In the main menu, click "Add device" → "Hearphones" → "Redmi Airdots".
4. Follow the instructions on the screen for pairing.
5. After connecting, go to the headphone settings and select "Gestural Management".

To improve sound:

• 🎛 Enable low frequency amplification in the smartphone equalizer (on Android: Settings) → Sound. → equalizer).
• 🔊 Use support players LDAC or aptX (e.g. Poweramp or Neutron).
• 🎧 Check the density of fittings – an improper landing worsens the bass.

💡

If you hear a hissing background in the headphones, try turning off the “Absolute Volume” function in the Android developer settings (Settings → About Phone → Assembly Number (click 7 times) → Developer settings → Turn off absolute Volume).

6. Update firmware and reset to factory settings

Redmi Airdots firmware updates automatically when you connect to the Mi Home app. However, sometimes a forced update is required (for example, if the headphones are glitching or do not support new features).

1. Open Mi Home and go to Redmi Airdots Settings.
2. Click on "Firmware Update" (if available).
3. Wait for the process to be completed (the headphones should be in the case with the lid open).

If the headphones are unstable (self-disconnected, not synchronized), perform a full reset:

Put the headphones in the case|Close the lid.|Hold the button on the case for 15 seconds|Wait for the flashing red/white|Reconnect.-->

Once reset, all the control and pairing settings will be reset.

• 🔗 Connect headphones to a smartphone.
• 🎛 Set up gestures in Mi Home.
• 🔊 Check the sound quality (may need to re-tuning the equalizer).

Note: Resetting does not solve problems with physical malfunctions (e.g., a discharged battery or a damaged speaker).If the headphones still do not work after reset, contact the service center.

7. Operational and life extension tips

To make Redmi Airdots last longer, follow these guidelines:

• 🔋 Charge the case with the original cable (using cheap cables can damage the charge controller).
• 💧 Avoid moisture despite the stated protection IPX4, Long-term contact with water will lead to corrosion of contacts.
• 🧹 Clean your earbuds and case with a soft brush (do not use alcohol to clean the earwaxes!).
• 🔄 Regularly (every 2-3 months) reset your settings to avoid software failures.
• 📴 Keep your headphones in a case – this prevents battery discharge and physical damage.

The average life of a Redmi Airdots battery is 2-3 years when used actively. If you notice that the battery life has decreased to 1-2 hours (at the initial 4-5), this is a sign of battery wear.

• 🔋 Try battery calibration: completely discharge the headphones (before switching off), then charge to 100% without interruptions.
• 🔄 Update your firmware through Mi Home – sometimes newer versions optimize your power consumption.
• 🛠 If nothing helps, contact the service to replace the battery (cost) ~1000-1500 rubles.).

💡

Do not leave the headphones on charging for more than 24 hours - this reduces the battery life, it is optimal to charge the case to 80-90% and disconnect from the network.

FAQ: Frequent questions about Redmi Airdots