How to completely disable the scooter Xiaomi: all the ways and nuances

Xiaomi electric scooters are one of the most popular means of transportation, but even experienced owners sometimes have questions about the correct shutdown of the device. It would seem that it could be easier than pressing the power button? However, Mi Electric Scooter scooters (M365, Pro, 1S, 4 and others) have features: an incorrect shutdown can lead to battery discharge, electronics failures or even wheel locking. In this article, we will discuss all official and alternative methods of shutdown, including emergency situations when the scooter does not respond to a button.

It is important to understand that the procedure differs depending on the model of the scooter, the firmware version and even the battery status. For example, the Xiaomi Mi Electric Scooter 4 Pro has a soft switching algorithm different from the M365, and old firmware may not have a quick shutdown function. We tested all methods on current models (2023-2026) and collected proven instructions from basic to emergency.

1. Standard power button shutdown

The most obvious and recommended way is to use a physical button on the steering wheel, but even here, there are nuances that are not covered in the official manual.

Make sure that the scooter is not moving (parking brake activated automatically at a speed of ≤ 3 km/h).

2. Once briefly press the power button - the charge indicator will light up on the display.

3. Hold the button for 3-5 seconds until the backlight goes out and the sound signal is heard (in models with a speaker).

⚠️ Note: If the scooter does not turn off after 5 seconds of retention, this may indicate a controller freeze or low battery charge (less than 5.

• ✅ Pros: Fast, safe for electronics, saves settings.
• ❌ Cons: Does not work in deep discharge or software failures.
• ⚠️ Feature: Xiaomi Mi Scooter 1S The newer button can require a hold of up to 7 seconds.

💡

If the scooter does not respond to a short press of a button, check if the Power Saving mode is activated in the Mi Home mobile application. In this mode, the display may not turn on with a single press.

2. Shutdown via the Mi Home mobile app

For Bluetooth-enabled models (Pro 2, 4, 4 Pro, etc.), remote control is available via the official app, which is useful if the power button is damaged or the scooter is out of reach.

Instructions:

1. Open Mi Home and connect to the scooter (make sure Bluetooth is on on the phone).
2. Go to the Control section → Turn it off.
3. Confirm the action (some firmware requires input) PIN-code, usually 0000 or 1234).

⚠️ Note: If the scooter is not displayed in the app, check:

• 📶 Bluetooth Module Status (Reboot Phone).
• 🔋 Charge level of the scooter (at <10% communication may be interrupted).
• 📱 App version (update to the latest in Google) Play/App Store).

Emergency shutdown: what to do if the scooter does not respond

Situations where the scooter is not switched off by a button or through an app are less common, but require a special approach. The reasons can range from firmware freeze to mechanical damage to the button. Here is the algorithm for actions:

Method 1: Forced resetting

Hold the power button for 10-15 seconds until all the lights go out. On models with a display (Pro 2, 4), the screen should blink and turn off.

• 🔌 Disconnect the charger (if the scooter is charging).
• 🔄 Repeat holding the button by simultaneously pressing the brake lever (sometimes this resets the controller).

Method 2: Battery extraction (for power users)

If the scooter is completely locked and does not respond to the buttons, the only way is to physically turn off the power.

1. Turn the scooter over and remove the bottom cover (a cross screwdriver will be required).
2. Find the battery connector (usually red or black) and gently disconnect it.
3. Wait 1-2 minutes and connect back.

4. Automatic shutdown: timers and energy saving

Modern Xiaomi scooters are equipped with automatic shutdown function to save charge. By default, the device turns off after 5-10 minutes of inactivity, but this time can be adjusted.

How to change the timer:

1. Connect the scooter to the Mi Home app.
2. Go to Settings. → Energy conservation.
3. Select the interval: 5 minutes, 10 minutes or Unplugged.

⚠️ Warning: Turning off automatic shutdown reduces battery life by 10-15% as the controller continues to consume energy in the background.

The scooter may also unexpectedly turn off in the following cases:

• 🔋 When the battery voltage drops below 28 V (critical discharge).
• ❄️ Lower temperature -10°C or higher +40°C (protection activates).
• 🚨 When a short circuit or overheating of the engine is detected.

5. Disconnection before transport or storage

If you plan to keep the scooter out for a long time (like in winter), simply pressing the power button is not enough. Incorrect storage can cause the battery to run deep and fail.

Step 1: Battery Preparation

Charge the battery to 40-60%, which is the optimal level for lithium-ion batteries with a long time of simplicity. Full charge or discharge accelerates the degradation of the cells.

Step 2: Complete shutdown

Turn off the scooter with a button, then hold it for 10 seconds to reset the controller, which will prevent background power consumption.

Step 3: Storage conditions

• 🌡️ Temperature: from +10°C +25°C.
• 💧 Humidity: not higher than 60% (exclude condensation).
• 🔌 Charger: disconnect from the scooter.

💡

Storage of a discharged scooter at sub-zero temperature can lead to irreversible damage to the battery after 1-2 months.

6. Frequent mistakes and how to avoid them

Even experienced users sometimes make mistakes when turning off the scooter, which eventually lead to breakdowns.

Error 1: Turning off during charging

If you disconnect the scooter from the network immediately after charging, the controller may not have time to complete the battery calibration, which leads to an inaccurate display of the charge level. Solution: After you complete charging, wait 5-10 minutes, then turn off the scooter.

Error 2: Holding the button for a long time without the need

Frequent forced shutdown (holding the button >10 seconds) can damage the power button microswitch. Use this method only in emergency cases.

Error 3: Ignoring Errors on the Display

If error codes appear on the screen before switching off (e.g. E:014, a brake problem), the scooter can lock on the next turn on. Always check for the decoding of errors in the instructions or through the Mi Home app.

Mistake 4: Storage with an empty battery

Xiaomi scooters lose up to 30% of their capacity when stored discharged for more than 3 months. Always leave a charge at 40-60%.

7. Features of switching off on popular models

The switching algorithm may vary depending on the scooter model. Let's look at the key differences:

⚠️ Attention: Xiaomi Mi Scooter 1S and Essential after updating the firmware to version 1.5.4+ You have a quick shutdown, which is a short two-time power button, but this mode doesn't reset the controller errors, so if you fail, use standard retention.

FAQ: Answers to Frequent Questions