Xiaomi Mi Weight Calibration: A Complete Guide to Accurate Measurements

The Xiaomi Mi Body Composition Scale has become an integral part of a healthy lifestyle for millions of users. It not only shows weight, but also analyzes body composition: fat percentage, muscle mass, water level and even bone density. However, even the most advanced equipment has to be adjusted periodically. Calibration of the scales Xiaomi Mi is a process that guarantees the accuracy of readings and prolongs the life of the device.

Many users have a problem when scales start lying, overweighting or underweighting, showing unstable data when weighing again, or refusing to turn on at all. The reasons can range from mechanical damage to software failures. In this article, we will examine all the ways of calibration, including manual adjustment through the Mi Fit application, hardware reset and sensor checkup. You will also learn how to avoid typical errors that lead to incorrect measurements.

It's important to understand that calibration is not a one-off procedure, and it's recommended to do it every time. 3-6 months, and after moving, falling weights or replacing batteries, if you just bought the device, the initial setup is required.

Why Xiaomi Mi scales show the wrong weight?

Before we start calibrating, we need to understand why the device is failing, and here are the main reasons why it's inaccurate.

• 🔋 Even if the indicator does not signal a low charge, weak batteries can distort the data.
• 📱 Unsynchronized application: If Mi Fit is not updated or is error-prone, the scales may not be transmitting data correctly.
• 🏋️ Uneven surface. Libras should be on a firm, flat base (like tile or laminate), carpet or soft floor distorts the results.
• 🧲 External interference: Electromagnetic fields from other devices (e.g. microwaves or routers) can affect sensors.
• 🛠️ Mechanical damage: A fall or impact can displace the internal sensors that make the measurements.
• 📡 Firmware failure. Rarely, but it happens that after updating the scales start to work incorrectly.

If the weight is more than the difference ±0.3 kg in re-weighing is a reason to calibrate, and it's also a wake-up call when the device is emitting an Err or Lo error, and 80 percent of the time, it's a simple recalibration, but sometimes you need a deeper diagnosis.

⚠️ Note: If the Xiaomi Mi scales show a weight of 0.0 or ---- When you turn on, it might indicate that the sensors' contacts are broken, and then calibration won't help, you need repairs.

Preparation of Xiaomi Mi weights for calibration

There are several mandatory steps that need to be followed before the procedure begins, and neglecting them can cause the calibration to go wrong and the scales to continue to lie.

Set the scales on a flat solid surface (tiles, laminate, countertop)

Make sure the batteries are charged (replace if necessary)

Turn off nearby electrical appliances (microwave, router, speakers)

Update the Mi Fit app to the latest version

Remove from the scales all foreign objects (dust, hair, stickers)-->

Pay special attention to the surface. If the floor is uneven, the scale sensors will register the skew, and the calibration will be error-proof. You can check the level (a smartphone application) or visually - the scales should not swing when you press corners lightly.

Also, be sure to update the firmware of the scales.

1. Open the Mi Fit app.
2. Go to Profile. → Devices → Your scales. → Settings (⚙️) → Firmware update.
3. If a new version is available, confirm the installation.

⚠️ Warning: Don't interrupt the firmware update process! If the scales turn off during installation, they may stop turning on. Wait for the 100% or Success label to appear.

Xiaomi Mi Body Composition Scale 2|Xiaomi Smart Scale 2|Xiaomi Mi Scale|Another model|I don't know.-->

Methods of calibration of Xiaomi Mi weights

There are three main calibration methods that vary in complexity and efficiency, and we recommend starting with the simplest and moving on to the more complex if the problem is not solved.

1. Automatic calibration via the Mi Fit app

This is the easiest way to do it, and it works for most models (Mi Body Composition Scale 2, Smart Scale 2, etc.) and automatically adjusts the sensors based on your data.

Instructions:

1. Open Mi Fit and go to the Profile section → Devices → Your scales.
2. Click on Settings (⚙️) → Calibration (or Weight adjustment).
3. Follow the instructions on the screen: You usually need to stand on the scale and wait. 5-10 seconds.
4. After completion, synchronize the data.

If the Calibration option is not on the menu, then your model does not support automatic tuning, in which case you go to the manual method.

Manual calibration using cargo

This method requires a reference weight (such as dumbbells or water bottles) and is suitable for all models, including older versions of the Mi Scale.

You'll need:

• 🏋️ Cargo weighing 5 kg, 10 kg or 20 kg (the more accurately known the weight, the better).
• 📝 Paper and pen for the records.
• 🔄 Ability to repeat weighing 3-5 once.

Step-by-step:

1. Turn the scales on and wait for 0.0 to appear.
2. Place the load on the center of the platform and record the readings.
3. Repeat the weighting 3 times and calculate the average.
4. If the difference between the standard and the readings of the weights exceeds ±0.2 kg, adjustment required.
5. In the Mi Fit app, find the Settings section of the Weights → Adjustment of readings and entering correction factor.

Critical error: if the scales show the weight of the cargo with a difference of more than 1 kg, this may indicate damage to the sensors, in which case calibration will not help - you need to replace the sensors.

Hardware reset (hard reset)

If the software methods didn't work, you can do a complete reset, which will return the scales to factory parameters and often solve problems with inaccurate readings.

For discharge:

1. Turn the scales over and find the Reset button (usually hidden under a sticker or rubber plug).
2. Press and hold the button. 10-15 seconds before the rST or 0.0.
3. Release the button and wait for the reboot.
4. Reconnect the scales via Mi Fit.

⚠️ Warning: After the hardware reset, all stored data (user profiles, weighing history) will be deleted!

💡

If the Reset button is missing, try an alternative: turn on the scales, then quickly press them 4 times in a row. On some models, this causes a reset.

Calibration of body composition sensors

Xiaomi Mi scales not only measure weight, but also analyze body composition (fat mass, muscle, water, etc.) for the accuracy of these indicators requires a separate adjustment.

Bioimpedance sensors (which pass a weak current through the body) are sensitive to:

• 💧 Hydration level. Measure at the same time (preferably on an empty stomach in the morning).
• 🏃 After exercise, the data may be inaccurate due to altered blood flow.
• 🩰 Weigh yourself without socks and with light clothes.
• 🧴 Creams and lotions. Fatty layers on the skin distort bioimpedance readings.

For calibration of body composition sensors:

1. In the Mi Fit app, go to Profile → Devices → Your scales. → Body analysis settings.
2. Select the Bioimpedance Calibration.
3. Enter your current parameters: height, age, gender.
4. Follow the instructions on the screen (usually you need to stand on the scale with bare feet).

If the scales show unrealistic values (e.g. 0% fat or 100% water), this may mean:

• 🔌 Problems with sensor contacts (you need to wipe the electrodes with alcohol).
• 📵 Sync failure with the application (reconnect the scales).
• 🧪 Incorrectly entered profile data (check height and age).

Frequent calibration errors and how to avoid them

Many users make common mistakes that nullify all efforts to adjust the scales.

Another common problem is the unstable readings of repeated weighings, if the scales show a different weight each time (for example, 70.2 kg, then 70.8 kg), this may be due to:

• 🧲 External interference (try weighing yourself elsewhere).
• 🔄 Sensor malfunction (check if the scales are wobbling when pressed).
• 📱 Synchronization failure (reconnect the scales to the phone).

If you have a problem after calibration, try an alternative method: weigh yourself on a mechanical scale (for example, in a clinic) and compare the readings. A difference of more than 0.5 kg is an excuse to contact the service.

💡

Calibration does not correct mechanical damage! If the scales have fallen or been hit, first check them for cracks or backlashes.

How to check the accuracy of the scales after calibration?

To make sure that the calibration is successful, you need to check the accuracy of the readings.

1. Reference load test: Take an object with a known weight (e.g., a 1kg pack of sugar or a 5kg dumbbell). Place it in the center of the scales and compare the readings. Acceptable error: ±0.1 kg for cargoes up to 10 kg, ±0.2 kg for heavier.
2. Stability test: Weigh 5 times in a row at intervals of 10 seconds. Write down the results. If the difference between the maximum and minimum values exceeds 0.3 kg, the calibration should be repeated.

Comparison with other weights

• Weigh yourself on a mechanical or electronic scale (in a pharmacy, gym).
• Compare the testimony.
• A difference of more than 0.5 kg indicates inaccuracy.

If the scales have passed all the tests, they can be considered calibrated, if not, try repeating the procedure or contact the service center.

Also, look at your body composition, and these are the norms for your age and your gender, for example:

• 👨 Men: Fat percentage 10-20%, muscle mass 35-45%.
• 👩 Women: percentage of fat 20-30%, muscle mass 25-35%.

If the values are very out of the norm (for example, 5% fat or 60% muscle), this may indicate that bioimpedance sensors are not working properly.

Xiaomi Mi weight maintenance: tips for durability

To ensure that the scales last long and show accurate data, follow these recommendations:

• 🧼 Regular cleaning: Rub the platform with a wet cloth 1 time per week. Use alcohol wipes to remove fat from sensors. Do not use abrasives - they will damage the coating!
• 🔋 Battery care: Replace batteries once in a while 6-12 Use only high-quality alkaline batteries (e.g. Duracell or Energizer) for prolonged non-use (>1 month) take out the batteries.
• 📦 Storage: Keep the scales in a dry place at a temperature 10-35°C. Avoid direct sunlight, which can warp plastic. Do not put heavy objects on the scales. 150 kilogram).
• 📱 Software Update: Check firmware updates in Mi Fit regularly. Don't interrupt the update process! After the update, perform a test weighing.

If Xiaomi Mi scales are no longer on or show an Err error, try:

1. Replace the batteries.
2. Perform a hardware reset (reset button).
3. Reconnect the scales to the Mi Fit app.
4. If nothing helps, contact the Xiaomi service center.

💡

If the scales start to gnaw after falling, check the integrity of the glass panel. Microcracks may be invisible, but they disrupt the sensors.

FAQ: Frequent questions about the calibration of Xiaomi Mi weights