Setup electric scooter Xiaomi S1: a complete guide for beginners

The Xiaomi Electric Scooter S1 is a stylish and functional vehicle that requires the right initial setup for a safe and comfortable ride. Many users are faced with questions: how to connect the device to a mobile application, calibrate the brakes, update the firmware or adjust the driving modes? In this article, we will discuss all the stages of preparing the scooter for operation, from unpacking to fine-tuning through official software.

The S1 is smart, with a Bluetooth module to communicate with your smartphone, a built-in display that shows speed and charge, and a regenerative braking system. But without the right setup, the scooter won't realize its potential. For example, uncalibrated brakes can lead to dangerous situations, and outdated firmware can reduce range. Next, you'll find step-by-step instructions with photos of interfaces, tips to correct common errors and answers to frequent questions.

Preparation of the scooter for the first set-up

Before you start setting up, make sure the scooter is fully charged. Charging from 0 to 100% on the first use takes about 5-6 hours. Use only the original Xiaomi power supply (voltage 42V/1.7A) to avoid battery damage. Connect the charger to the socket and then to the socket on the steering column - the indicator on the charge should light up red.

While charging, check the configuration:

• 📦 Xiaomi scooter S1 In the assembled form (wheels and steering wheels are already installed)
• 🔌 Charger with cable
• 🔧 Steering tool (six-sided key)
• 📄 Guarantee card and instructions in several languages
• 🔄 Replacement camera (in some configurations)

After fully charging, press the power button on the steering wheel - the scooter will sound and a welcome message will appear on the display. If the screen does not turn on, check the density of the charger's contacts or try to restart the scooter with the power button for 5 seconds.

💡

If the scooter does not respond to the on button, try to sway it slightly back and forth - sometimes the motion sensor blocks the activation in a static position.

2. Installation and configuration of the Mi Home mobile application

To fully work Xiaomi S1 you need to install the official Mi Home app (available for Android and iOS). Download it from Google Play or the App Store.

1. Sign up or sign in to an existing Xiaomi account (use the same region as when you bought a scooter).
2. Click "Add device" (the icon "+" in the upper right corner).
3. Select the category "Transport", then "Electrical Scooter".
4. In the list of models, find the Xiaomi Electric Scooter S1.

Follow the instructions on the screen. The app will suggest that you turn on Bluetooth and geolocation — allow access, otherwise the connection will not work. When the scooter appears in the list of devices, assign it a name (for example, "My S1") and select an icon for quick access.

After successful connection on the main screen will appear the main parameters:

• 🔋 Battery level (in percentages and volts)
• 🚀 Current speed (updated in real time)
• 📊 Distance travelled (mileage counter)
• ⚙️ Access button to settings

Calibration of brakes and wheels

Calibration of brakes is a critical step that affects safety. Incorrectly adjusted brakes can lead to skidding or increase the braking distance. Xiaomi S1 uses a combined system: disc brake on the rear wheel and electronic (regenerative) on the front.

For calibration:

1. Put the scooter on a flat surface and turn it on.
2. In the Mi Home app, go to Settings → Calibration of brakes.
3. Follow the instructions: first press the rear brake lever to the end, then the front.
4. Wait for the audible signal to confirm the successful calibration.

If the brakes creak or block the wheel too sharply, check:

• 🔧 Rear brake cable tension (adjusted by nut on the skirt)
• 🛞 Wear of brake pads (replace if the thickness is less than 1.5 mm)
• 🔄 Rotor cleanliness (remove dirt or oil from disk)

The rear brake locks the wheel smoothly|The front electronic brake is activated without jerks|No extraneous sounds when braking|The braking distance at a speed of 15 km / h does not exceed 3 meters-->

Note: after replacing the wheels or brake pads, the calibration must be repeated again, otherwise the ABS system may not work properly.

4. Update firmware: why and how to do

The manufacturer regularly releases firmware updates for Xiaomi S1, which improve:

• ⚡ Energy efficiency (increased range of travel) 5-10%)
• 🛡️ Stability of electronic components
• 🔄 The logic of regenerative braking
• 📱 Compatible with new versions of the Mi Home app

To update the firmware:

1. Connect the scooter to the Mi Home app.
2. Go to Settings → Update firmware.
3. If a new version is available, click "Update".
4. Wait until the process is complete (the scooter will reboot automatically).

⚠️ Warning: Do not interrupt the update or turn off the scooter during the process. If the battery runs below 20%, the update will be blocked - charge the device before starting.

After the update, check:

• 🔄 Correctness of the display speed on the display
• 🔋 Charge level indications (sometimes battery recalibration is required)
• 🛑 Brake performance in different modes

5. Setting up driving modes and restrictions

Xiaomi S1 offers three main driving modes, which differ in maximum speed and responsiveness:

To change the regime:

1. Twice press the power button on the steering wheel.
2. The display will display the current mode (letters E, S or P).
3. With a quick press, switch the modes in a circle.

Through the Mi Home application, you can configure additional parameters:

• 🔒 Children's mode (speed limit to 10 km / h)
• 🚦 Cruise control (automatic speed maintenance)
• 🔋 Recovery level (weak/medium/strong)

⚠️ Attention: In Sport mode, the scooter consumes 30% more energy and the braking distance increases.

Setting up the illumination and sound signals

Xiaomi S1 built-in LED-It's a lighting system (front and back) and a beep, and these features not only add style, but also make it safer in the dark:

1. In the Mi Home app, go to Settings → Lighting.
2. Select the mode of operation: 🌓 Auto - turns on at low lighting 🔦 Always on. 🌑 Off.

Adjust the brightness (3 levels).

The audio signal is configured in the same menu, 5 tunes are available, and the ability to turn off the signal completely (not recommended for driving in the city). To give a signal manually, press the button with the image of the call on the steering wheel.

Tip: If the headlight is dim, check the glass cleanliness (wipe with an alcohol napkin) or the contacts of the connector under the steering wheel. In some cases, resetting the backlight settings through the app helps.

7. Diagnostics and elimination of typical problems

Even after the right setup, the scooter may not behave properly. Consider the most common problems and solutions:

If the scooter gives an E01 (motor problem) or E02 (brake error), try:

1. Turn off and turn on the scooter.
2. Reset settings via the app (Settings → Reset).
3. Contact the service center if the error is repeated.