How to turn on Bluetooth on the Xiaomi scooter: instructions for all models

Xiaomi electric scooters are one of the most popular means of transportation in the city, but their full use is impossible without connecting to a smartphone via Bluetooth. This module allows you to synchronize travel data, update firmware, adjust ride modes and even block the scooter from theft, but many users face difficulties when first turning on Bluetooth — especially when it comes to budget models like M365 or new versions of the 4 Pro.

In this article, we will not only discuss the basic procedure for activating Bluetooth on Xiaomi scooters, but also the nuances for specific models, typical connection errors, and methods for diagnosing problems.

If you've never connected a scooter to your phone before or encountered a message that says "Device not found," the following sections will help you figure it out without going to the service center. And for power users, we've prepared advanced settings and life hacks to optimize the Bluetooth module.

Which Xiaomi models support Bluetooth?

Before you try to turn on Bluetooth, make sure that your model of Xiaomi scooter is equipped with this module at all. Most modern devices support wireless communication, but there are exceptions, for example, some of the most popular devices are not connected to the Internet. OEM-Chinese market version or very old models.

Here is the full list of Xiaomi scooters with Bluetooth (as of 2026):

• 🛴 Xiaomi M365 (all modifications, including M365 Pro)
• 🛴 Xiaomi Pro 2 (including versions with larger battery)
• 🛴 Xiaomi 1S (and his clones under other brands)
• 🛴 Xiaomi Essential (budget model with stripped-down functionality)
• 🛴 Xiaomi 4 Pro (flagship model with improved Bluetooth 5.0)
• 🛴 Xiaomi Electric Scooter 3 Lite and 3 Pro

Note that even if your model is on the list, Bluetooth can be disabled at the firmware level, for example, some scooters purchased on AliExpress without official localization require a software update through Mi Home or Xiaomi Scooter.

Step-by-step: how to turn on Bluetooth on a scooter

The Bluetooth activation process on most Xiaomi models is the same, but there are nuances depending on the firmware version and the mobile app. We will look at a universal algorithm that is suitable for 90% of devices.

Preparation of the scooter

Before turning on Bluetooth, make sure that:

• 🔋 The scooter is charged at least 20% (at low charge, the communication module may not be activated).
• 📱 Bluetooth enabled and permissions for Mi Home or Xiaomi Scooter app.
• 🔄 The scooter is in standby mode (not moving, not blocked).

2. activate Bluetooth via the power button

On most Xiaomi models (except the 4 Pro and 3 Lite), Bluetooth is automatically activated when you press the power button. However, if the scooter is not detected by the phone, perform a forced activation:

1. Hold the power button for 3 seconds until the lights light up.
2. Press the button again and the single signal must be played (this means that Bluetooth is active).
3. On the phone in the list of available devices will appear the name of the model (for example, NINEBOT BY SEGWAY ESx for M365).

For Xiaomi 4 Pro and 3 Lite models, the process is slightly different: Bluetooth only turns on after connecting to the application. If the scooter is not visible in the list of devices, try rebooting it (hold the power button for 10 seconds).

3. Connection to the annex

After activating Bluetooth on the scooter:

1. Open the Mi Home or Xiaomi Scooter app.
2. Click Add Add the device (+) → Choose the category "Self-Self-Self-Self-Self-Self-Self-Selected».
3. Find your model in the list and confirm the connection.
4. If necessary, enter PIN-code (default 0000 or 1234).

If the app requests a firmware update, don't refuse. Older versions of the software often have Bluetooth bugs that interrupt communication or the scooter does not respond to commands.

💡

If the scooter does not connect, try to remove it from the list of conjugated devices in the phone settings and repeat the procedure again.

Frequent problems and their solutions

Even after Bluetooth is turned on correctly, users are faced with connection errors, and let's look at the most common cases and how to fix them.

1.The scooter is not visible on the device list

If the phone does not find the scooter, check:

• 🔍 Distance between devices – Bluetooth on scooters Xiaomi works at a distance of up to 10 meters, but for the first connection it is better to keep the phone closer than 1 meter.
• 📵 Interference – other wireless devices (earphones, smartwatches) can create conflicts.
• 🔄 Flight mode - some phones have Bluetooth shut down along with the mobile network.
• 🔋 Scooter charge – at a level below 15%, the Bluetooth module may not respond.

2. the connection is interrupted or lags

If the connection is interrupted during the trip or the data in the application is updated with a delay, try:

• 📱 Update the app – older versions of Mi Home often conflict with new firmware scooters.
• 🔄 Reboot the scooter – hold the power button for 10 seconds, then turn it on again.
• 📶 Change the region in the app – if you use Xiaomi M365 With firmware for China, select the “China Mainland” region in the Mi Home settings.
• 🛠️ Reset the scooter settings - in extreme cases, reset through the application (section "Device settings»).

3. "Device not supported" error

This message usually appears if:

• 📱 You use an unofficial firmware (for example, a custom version for overclocking).
• 🌍 The region in the Mi Home application does not coincide with the region of the scooter firmware.
• 🔄 The scooter was previously paired with another phone, and the data was not reset.

Decision:

1. Remove the scooter from the list of devices in Mi Home.
2. Reset the scooter settings (see spoiler above).
3. Install the “China Mainland” region in the app and reconnect.

Bluetooth settings in the Xiaomi Scooter app

Once you’ve successfully connected, open the Bluetooth settings section of the app, and features that many users miss are available here:

Note the Safe Shutdown feature (available in Xiaomi Scooter for the 4 Pro) which automatically breaks the Bluetooth connection when driving at speeds above 25 km/h to reduce battery load.

💡

Regularly update the firmware of the scooter via Bluetooth – this fixes vulnerabilities and improves the stability of communication.

Security: Why you can't leave Bluetooth on

Many users do not turn off Bluetooth on the scooter after use, which poses risks:

⚠️ In 2023, researchers from Kaspersky discovered a vulnerability in the Bluetooth protocol of Xiaomi scooters M365, The vulnerability was fixed in firmware no later than 1.5.4, but the risk remains for devices without updates.

Major threats:

• 🔓 Unauthorized access – Attackers can connect to the scooter and change settings (for example, disable the speed limiter).
• 📍 Location tracking – Bluetooth can determine the approximate location of the scooter (and, accordingly, the owner).
• 🔋 Battery discharge – Bluetooth module consumes up to 5% charge per hour in standby mode.

Safety recommendations:

• 🔄 Turn off Bluetooth on the scooter after each trip (hold the power button for 2 seconds until the indicator flashes blue).
• 🔒 Install. PIN-code for connection (in the settings of the Xiaomi Scooter application).
• 📱 Check the list of conjugate devices on your phone regularly and delete unknown devices.

💡

If you leave a scooter in the parking lot, turn on the “Block when Bluetooth is turned off” function in the application settings, which will prevent theft even if the attacker reboots the scooter.

Advanced Settings: How to Improve Bluetooth Stability

If you are an experienced user and want to optimize the operation of the Bluetooth module, use these tips:

1. Change of the firmware region

Firmware for different regions may conflict with Bluetooth settings.

1. Open Mi Home and go to your profile settings.
2. Choose the China Mainland region (even if you are not in China).
3. Remove the scooter from the list of devices and connect again.

This often solves communication breakdown problems on models M365 Pro 2.

2. power saving off on the phone

On Android smartphones:

1. Go to Settings → Applications → Mi Home → Battery.
2. Turn off the option “Battery Optimization”.
3. Enable "Stop" and "Work in the background".

On the iPhone:

1. Open Settings → Bluetooth.
2. Find your scooter in the list and click "i» → «Forget this device».
3. Reconnect by allowing notifications.

3. Use of alternative applications

The official Mi Home app doesn't always work well.

• 📱 Xiaomi Scooter (more advanced Bluetooth settings).
• 📱 Ninebot (for models released after 2022).
• 📱 ScooterHacking Utility (for experienced users, allows you to change the parameters of the Bluetooth module).

⚠️ Note: Apps like ScooterHacking Utility require you to unlock the firmware, which cancels the warranty. Use them only if you understand the risks.

FAQ: Answers to popular questions