How to charge wireless headphones Xiaomi Redmi Airdots: instruction 2026

Xiaomi Redmi Airdots wireless headphones remain among the most popular TWS-But even these proven gadgets have problems with charging, from slow battery recovery to complete failure of the case to give signs of life. from the selection of cable to the diagnosis of malfunctions, and also reveal the hidden functions of the case, which are not written in the official instructions.

Redmi Airdots (including Airdots models) 2/3/Pro) They use lithium polymer batteries that are sensitive to voltage and temperature changes. Incorrect charging can shorten the battery life of the battery. 30–40%, And in some cases, we're going to take the device out of action. 2026 year, including tips from Xiaomi service centers and test results from independent laboratories.

1. Supply kit and compatible chargers

In the box with Redmi Airdots you will find only USB-C cable (post-2020 models) or microUSB (early versions), but no power supply. This is not an accident, the manufacturer recommends the use of adapters with certain characteristics:

• 🔌 Tension: 5V (standard USB-port)
• ⚡ Current power: from 0.5A before 2A (optimally — 1A)
• 🔋 Type of connector: USB-A block-side, USB-C/microUSB on the case side (depending on the model)

Chargers from Xiaomi smartphones (for example, from Redmi Note) will be suitable 8/9/10), but there are nuances:

⚠️ Attention: Use of chargers with higher current 2A (For example, laptops can cause the case battery to swell, and signs of a problem are that the case is not closing tightly or there are cracks in the case.

If you lose the original cable, choose certified analogues with the labeling USB-IF (Cheap Chinese cables without protection can short-circuit the power controller of the case - it is non-repairable breakdown.

2. Step-by-step instruction: how to charge the case and headphones

The Redmi Airdots charge process is two-step: first, the case is charged, then the case headphones themselves, and we'll take each step in terms of the different models.

Charging the case from the grid

Connect the cable to the case before the characteristic click

Use the exit adapter 5V/1A–2A

Check the charging indicator (should burn red)

Do not interrupt the process until full charge (the indicator will turn green)

Turn off the cable after completion-->

Algorithm of action:

1. Open the case cover and make sure the headphones are removed (they can be charged later).
2. Connect the cable to the connector on the back of the case. For Airdots 3 Pro models, the connector is on the bottom.
3. Insert the other end of the cable into the charger, and the indicator on the front panel of the case should light up red (Airdots 2 - orange).
4. Wait for the indicator to change color to green (or fade in some modifications), this signals 100% charge.

The time of full charge of the case depends on the model:

• 🕒 Redmi Airdots (1st generation): 2–2.5 hours
• ⚡ Airdots 2/2S: 1.5–2 hour
• ⚡⚡ Airdots 3/3 Pro: 1–1.5 The hour (thanks to the optimized controller)

Charging the case headphones

Headphones start charging automatically when placed in a case, but there are several rules:

1. Make sure that the contacts on the headphones and inside the case are clean (wipe with an alcohol napkin if necessary).
2. Close the case cover – in some models, charging will not begin if the cover is open.
3. The headphones should flash red when charging starts and go out after completion.

⚠️ Note: If one of the headphones is not charged, check the integrity of the spring contacts inside the case. If they are damaged (for example, after a fall), you need to replace the case - repair is more expensive than a new device.

💡

To speed up charging, pre-discharge the headphones to 0% (until they turn off) and this will reset the power controller and increase the recovery rate by 15-20%.

3. How to check the charge level of the case and headphones

Redmi Airdots does not have a digital charge indicator, but there are several ways to estimate the current level:

Method 1: According to the indicator on the case

• 🔴 Red/orange: 0-50%
• 🟡 Yellow: 50-80% (only on Airdots 3 Pro)
• 🟢 Green: 80-100%
• ⚫ Indicator does not burn: the case is completely discharged or defective

Method 2: Through the Mi Home app (only for some models)

Airdots 3 Pro and newer models support the display of the charge level in the official Mi Home application (section "Devices" → "Headphones:

1. Connect the headphones to the smartphone via Bluetooth.
2. Open Mi Home and update the data (swipe down on the home screen).
3. Click on the icon of headphones - information about the charge of the case and each headphone separately will appear.

Method 3: By the behavior of headphones

Indirect indications of discharge:

• 🎵 The sound becomes quieter when the charge level is below 20%.
• 🔊 Headphones are given a voice warning "Battery low" (models with support for voice prompts).
• ⏱️ The headphones are turned off 5-10 minutes after the last warning.

4 Common charging errors and how to avoid them

Even power users make mistakes that shorten the lifespan of Redmi Airdots.Here's the top-5 problems and solutions:

Mistake 1: Using unoriginal cables

Cheap cables without protection can:

• 🔥 Cause overheating of the power controller (case becomes hot to the touch).
• ⚡ Lead to unstable tension, which is why the case is charged with "twisting".
• 💥 Provoke a short circuit (in 10% of cases leads to a case breakdown).

Solution: Use labeled cables USB-IF Or Xiaomi's original. A good alternative is Anker or Baseus cables.

Error 2: Charging at extreme temperatures

Redmi Airdots Lithium Polymer Batteries are Temperature Sensitive:

• ❄️ Below. +5°C: Battery capacity temporarily drops by 30-40%.
• 🔥 Higher. +35°C: Battery degradation is accelerating (capacity loss by 2–3% per month).

Solution: Charge the case at room temperature (15–25)°If the headphones overheat in the sun, let them cool for 10-15 minutes before charging.

Mistake 3: Storage of a discharged case

If you leave the case discharged by 0% for more than 2 weeks, the battery can:

• 🔋 Fall into the "deep discharge" - after that the case will not turn on even when connected to the network.
• 💀 Completely lose capacity (not refurbishable).

Solution: If you don't use headphones for a long time, charge the case to 40-60% and store it in a dry place. It's optimal to repeat the charge every 1-2 months.

Error 4: Breaking the charge

If the case is disconnected from power to full charge (e.g. at 80%), the power controller can:

• 📉 Incorrectly calculate the capacity of the battery, which is why the case will discharge faster.
• 🔄 Enter "calibration" mode, which takes up to 3 charging cycles.

Solution: Wait until the indicator turns green, even if the case is already "almost charged."

Error 5: Using wireless charging (for incompatible models)

Only Redmi Airdots 3 Pro supports Qi wireless charging, and if you try to charge other models (such as Airdots 2) on a wireless station, you will:

• 🔋 Lack of charging (case just doesn't respond).
• 🔥 Overheating of internal components (in rare cases).

Solution: Check the compatibility of the model with wireless charging in the specifications on the Xiaomi website.

💡

The most common reason for the failure of the case is the use of non-original cables and adapters with unstable voltage. 60% of calls to service centers are associated with this.

5. How to extend the life of Redmi Airdots battery

The average battery life of Redmi Airdots is 2-3 years (300-500 charge cycles). To delay replacement as much as possible, follow these recommendations:

Advice 1: Battery calibration

Once every 2-3 months, perform a full cycle of discharge-charging:

1. Discharge the case and headphones until automatically shut down.
2. Charge the case to 100% without interruption.
3. Repeat 2-3 times in a row.

This helps the power controller to correctly determine the charge level.

Advice 2: The optimal charge level for storage

If you don’t use headphones for a long time (for example, during vacation):

• 🔋 Charge the case to 40-60%.
• 📦 Store in a dry place at a temperature of 15-25°C.
• 🔄 Once every 1-2 months bring the charge to 100% and again reduce to 50%.

Advice 3: Cleaning contacts

Contaminated contacts impair charging and can cause corrosion.

• 🧴 Soft toothbrush (dry!) – to remove dust.
• 🧴 Alcohol napkin - to remove fat and oxidation.
• ❌ Do not use: water, acetone, metal objects.

Advice 4: Update firmware

For Airdots 3 Pro and newer models, Xiaomi is releasing firmware updates that optimize battery consumption.

1. Connect your headphones to your smartphone via Mi Home.
2. Go to the headphone settings.
3. Click on "Update firmware" (if available).

💡

If the case starts to charge more slowly, try using a different cable or adapter, and in 40% of cases, the problem is not the case, but the power source.

6.Diagnostics of malfunctions: case is not charged

If the Redmi Airdots case has stopped charging, first identify the symptom:

Case drop instructions

If the case is unstable (for example, does not hold a charge or does not sync with headphones), reset:

1. Remove the headphones from the case.
2. Press the button on the back of the case for 10-15 seconds.
3. Wait until the indicator flashes white and red.
4. Release the button and connect the case to the charger.

⚠️ Note: If the case stopped turning on after the reset, this may indicate a malfunction of the power controller, in which case the repair will cost more than the purchase of a new case (the price of spare parts is 80-90% of the cost of the new device).

When to contact the service

Self-repair of the Redmi Airdots case is possible only when replacing the battery (if you are an experienced user).

• 🔥 The case warms up when charging (temperature above 40)°C).
• 💥 There was a smell of burning or case swelling.
• 🔋 The battery is discharged in a few hours without use.

7. Alternative charging methods (for emergency cases)

If you don't have the original cable or adapter, you can use alternative methods, but remember, these methods are not recommended for permanent use.

Method 1: Charging from a computer or laptop

USB-computer ports 5V/0.5A, That's enough for slow charging:

• ⏳ Charging time will increase to 3-4 hours.
• 💻 Some laptops are turning off power USB-sleep-port.
• ⚠️ Risk of interruption of charging when updating drivers.

How to charge:

1. Connect the case to USB-Port 2.0 or 3.0 (blue connectors).
2. Make sure ports are not turned off in power settings Windows/macOS.
3. Don't use it. USB-Hubs – they may not provide sufficient current.

Method 2: Charging from Power Bank

Mobile batteries are suitable, but there are nuances:

• ✅ The most popular models are Xiaomi Power Bank 3 and Baseus. 10000mAh.
• ❌ Low-cost power bank without overload protection.
• ⚡ Optimum current: 1A–1.5A.

Method 3: Wireless charging (only for Airdots 3 Pro)

If your model supports Qi:

1. Place the case at the charging station center up (there is a coil).
2. Make sure the station is not giving more. 5W (10W can overheat the case).
3. Charging time: ~2.5 hours (slower than cable).

⚠️ Note: Do not put on wireless charging metal objects (keys, coins) along with the case - this can cause a short circuit and the station failure.

8. Frequently Asked Questions (FAQ)