Xiaomi Redmi Note 4X: how to turn on the phone and fix the malfunction

Xiaomi Redmi Note 4X, despite its age, remains a popular device due to the reliable Snapdragon 625 processor. However, users often face a situation where the device stops responding to presses or does not give signs of life. Turning on the device is the basic operation, but in case of failures it requires knowledge of specific key combinations and sequence of actions.

The reasons for the lack of reaction can range from simple battery discharge to software errors of the bootloader or hardware damage to plumes. In this guide, we will discuss all possible scenarios, from a standard start to complex cases when you need to log into Recovery or Fastboot mode.

A careful study of the instructions below will help you resuscitate your device without going to a service center, and it is important to understand the difference between a shutdown and a deep discharge, and how to interpret vibration response or LED display signals correctly.

Standard start-up of the device

To normally turn on a serviceable Redmi Note 4X smartphone, you need to do a simple sequence of actions: Find a power button on the right side of the case, which can also be used to lock the screen, press and hold it for 2-3 seconds before the MIUI logo appears.

If the phone is completely off but the battery is charged, the screen will light up almost instantly. If the device is in deep sleep, it may require a longer hold on the button. Sometimes the system requires a start confirmation if a lock has been installed. SIM-map.

⚠️ Note: If the power button is pressed, the screen flashes or sounds but no image, it may be the display matrix or plume that is the problem, not the software part.

In some cases, especially after a firmware update, the first run may take longer than usual.Don't panic if the logo hangs on the screen for longer than a minute - this is a normal process of initializing system files.

💡

Before storing your phone for long periods, be sure to charge it up to 60-70% to avoid deep battery drain.

Actions at deep battery discharge

One of the most common reasons why the Xiaomi Redmi Note 4X doesn’t turn on is the critical discharge of the lithium-polymer battery.When the charge level drops below a certain threshold, the power controller blocks the system from starting to protect the cell’s chemistry.

In this state, the phone may not respond to short presses of the power button. You will need to connect the original charger and a good quality cable. Pay attention to the charging indicator: it can light up in orange, signaling the process of energy storage.

If the light doesn't turn on right away, leave the phone charging for at least 30-60 minutes, then try to turn the device on in the standard way. Sometimes you need to "swing" the battery to reach the minimum voltage needed to start the processor.

• 🔋 Use only certified Micro-USB cables, as cheap analogues may not pass the desired current.
• ⏳ Don’t try to turn on your phone every 5 minutes – it resets the process of precharging the controller.
• 🌡️ Check the temperature of the device: if the phone was in the cold, let it warm to room temperature.

It's worth noting that older batteries can have a voltage memory effect, which can cause the charge indicator to show incorrect data immediately after turning on.

Forced system reboot

If the Redmi Note 4X is stuck, the screen is black, but the phone is responding to buttons, or the system is unstable, a forced reboot may be required, a method similar to removing the battery on older models and resetting temporary operating memory errors.

To perform this procedure, you need to press the power button and hold it for 10-15 seconds. Some versions of MIUI require simultaneous pressing of the power button and the volume button. Hold the buttons until you feel a vibration response or a logo appears.

Power + Volume Up (10-15 seconds)

This method is safe for user data, as it does not affect the file system, but only interrupts current processes and initiates a cold start. If after a reboot the problem repeats, the newly installed application may conflict.

⚠️ Warning: Do not use the forced reboot method regularly. frequent abrupt shutdown can damage the database of contacts or messages.

In the rare cases where the touch screen doesn't respond, it's the physical button combination that remains the only way to control.Make sure you hold the buttons long enough, as the system can ignore short taps when getting stuck.

Enter Recovery and Fastboot Mode

For deeper diagnostics or flashing, the Xiaomi Redmi Note 4X uses special boot modes. Recovery mode allows you to reset settings or install updates, and Fastboot is designed for low-level interaction with your PC.

To get into the Recovery menu, turn off your phone completely. Then simultaneously press the power button and the Volume Up button. Hold them until a menu with a few items appears on a black or orange background.

The algorithm is similar to Fastboot mode, but uses a Volume Down button. Click the power and Volume Down before an image with a hare repairing an android appears. This is a state often required to unlock the bootloader via Mi Unlock.

Navigation in the Recovery menu is done with volume buttons, and the choice is confirmed by the power button. Be careful when choosing the Wipe Data item, as this action will delete all your photos and contacts.

Diagnostics of the black screen

The situation when the Redmi Note 4X is turned on (there is sound, vibration), but the screen remains black, requires special attention.This can be either a software interface failure or physical damage to the display or connector.

Try pointing a bright flashlight at an angle, and if you see a dim image of the interface, it means that the backlight of the display has burned, and if there is no image at all, but the phone responds to calls, the problem may be the plume or the screen controller.

Sometimes it helps to connect to a computer via USB. If the PC makes a sound of the connection of a new device and determines the model of the phone, then the motherboard is alive, in this case, connect an external monitor via OTG (if supported), or just check the integrity of the plume when disassembling.

• 🔦 Checking the backlight with a flashlight helps to identify hidden defects of the matrix.
• 💻 Connecting to a PC allows you to check whether the logical part of the board works.
• 🔌 Careful shutdown and plugging of the display plume can restore contact.

Do not ignore the signs of falling or getting moisture, preceding the appearance of a black screen. In such cases, turning on yourself can aggravate the situation, causing a short circuit.

💡

Black screen with a working phone in 80% of cases indicates a hardware malfunction of the display module or its plume.

Frequent startup problems and their solution

Owners of the Xiaomi Redmi Note 4X may experience a cyclical reboot known as a "bootloop."The phone turns on, shows the MIUI logo, goes off and re-energizes, most often after a failed upgrade or system partition overflow.

To solve the problem, try entering Recovery mode (as described above) and select Wipe Data. Remember, this will return the phone to factory settings. If this does not help, you will need to flash the device through your computer using the Mi Flash Tool utility.

Another problem is that the phone is warming and not turning on, which could indicate a short circuit in the power supply or a battery failure, in which case leave the device alone for a few hours, disconnecting from charging, and then try to start again.

⚠️ Warning: If the phone heats up in the area of the camera or processor immediately when connecting the charge without turning on, immediately turn it off - there is a high risk of battery fire.

Regularly cleaning the cache and not installing applications from unverified sources will help avoid software conflicts that lead to boot failures. Watch out for free space in memory, a crowded /data partition often causes cyclical reboots.

Questions and Answers (FAQ)