How to turn on the sound on the video recorder Xiaomi 70mai

Xiaomi’s modern car DVRs and its 70mai sub-brand have proven to be reliable in-car fixing devices, but many users face a situation where video is saved without audio, which can become critical in controversial situations on the road. Activating the microphone is not just a matter of convenience, but an important part of the evidence base for analyzing incidents. Most of the time, the lack of sound is due to software settings that can be disabled or triggered by a firmware update.

In this article, we will discuss in detail the algorithm for turning on audio on different models of the 70mai line. You will learn where to look for hidden switches in the menu, how to properly set up a cyclic sound recording and what to do if the microphone stopped working after the power connection. Understanding the principles of the recorder audio system will allow you to avoid situations where the most important negotiations or brake sounds will be left behind.

It's worth noting that the 70mai mobile app interface and the device menu may vary slightly depending on the software version. However, the setting logic remains the same across the ecosystem. We'll look at both standard scenarios and specific cases that require interference with system settings. Audio streaming is an integral part of a full video recording, and the correct configuration is mandatory for each owner.

Checking the basic settings in the device menu

The first step in the absence of sound is to check the main menu of the DVR itself. Often users accidentally turn off the microphone through physical buttons or touch screen without noticing the status change. On the device screen, you need to find the speaker icon or item marked as Mic. If the speaker is crossed out on the icon, then the recording of the sound is blocked at the hardware level.

To access settings on non-touch screen models such as the 70mai Lite or Pro Plus, a single control button is used. A short press changes modes, and a long hold (about 2-3 seconds) opens the menu. In the list of parameters, you should find the section responsible for audio. Here it is important to make sure that the switch is in the position of ON or Enabled. Some models have a separate button on the case that instantly silences the microphone - check if it is pressed.

⚠️ Note: Some models will display a sign on the screen when the microphone is turned off. If you see a crossed-out microphone icon in the corner of the display while recording, the sound will not be saved even if the settings are all on.

In touchscreen models like the 70mai A500S or A800S, swipe down to call a quick menu and check the status of the audio. If standard methods fail to turn on the sound, a software glitch may have triggered and a device reboot may be needed. Restart often solves problems with suspended audio capture services.

💡

Use voice control if your model supports it. Say "Turn on sound" or "Enable sound" to quickly activate the microphone without distraction from the road.

Set up audio recording through a mobile application

More flexible control is provided by the official 70mai app, which syncs with the registrar over Wi-Fi. Once you connect to the device via your smartphone, go to the settings section (cog icon). Here is the Record Sound or Sound Record. Make sure the slider is activated. The advantage of setting up through the application is that you see a full list of available options that can be hidden in the simplified menu on the registrar screen.

You can also adjust the behavior of the microphone in different events, for example, in some versions of the firmware, you can automatically turn off the sound when parking or at night. Check the Advanced Settings section. This can contain parameters that affect the sensitivity of the microphone and noise reduction algorithms.

Once you have the audio, you should do a test piece. Record a short video, talk next to the car, and then play the file. If the sound is in the app when you're viewing it over Wi-Fi, but it's not on the memory card after you've extracted it, the problem may lie in the file system or the encoding format. Synchronizing the settings between the app and the device is key to stable operation.

Features of cyclic recording and sound

Cycling is the standard feature for modern DVRs, including the Xiaomi 70mai. It allows you to continuously record video, overwriting old files with new ones when the card memory is full. However, there are nuances to how the audio stream works in this mode. In some configurations, users notice that sound is only recorded in manually created files (by button), and automatic cycling videos do not get audio. This may be due to the recording segment length settings.

In the menu of the device, find the Record Time option or the duration of the video. The optimal value for maintaining the integrity of the audio stream and viewing is considered to be an interval of 1 or 3 minutes. If you choose the value "off" (recording with one file before filling the map), the risk of data loss when the power failure is maximum, and the sound may be cut off. It is also worth checking whether the G-Sensor mode is activated for too high sensitivity, since when the files are activated often, file protection can block the normal operation of the audio recording buffer.

If you use a large memory card (128 GB or higher), make sure it is formatted directly in the registrar. The file system must be compatible with continuous writing. Errors in the structure of the card partitions can cause the video stream to be written and the audio track to be lost or unreadable for the player. Formatting in the device is a mandatory procedure for a new card.

Diagnostics of microphone problems

When the settings are checked but there is no sound, the microphone may need to be more deeply diagnosed. The first reason may be a physical lock of the microphone hole. On 70mai cases, the input hole for sound is usually located on the end or back. When the recorder is mounted behind the rear-view mirror or under the tinted film, the microphone may be blocked, in which case the device writes silence or numb noise, even if the microphone is technically correct.

The second common problem is the use of low-quality memory cards. Cheap cards may not be able to handle the high bitrate recording speed of video and audio at the same time. This leads to desynchronization or complete disappearance of the sound track. Try replacing the card with a certified model with a speed class U3 or V30. It is also worth checking whether the memory card is full — some models stop writing sound when less than 10% of the space is free.

⚠️ Note: Do not use memory cards larger than 64 GB in models that do not support the standard SDXC This can cause the entire device to malfunction, including the failure of the audio module.

If the software reset and the card change didn't work, the audio module itself may have failed, which is rare, but possible when moisture is injected or there are extreme temperature changes. To check, you can try resetting the device to factory settings through the System → Factory Reset menu, which will remove all user configurations and return the original parameters of the audio system.

Specifics of work in the parking mode

Parking Mode on the Xiaomi 70mai DVR has its own features of working with sound. In order to save energy and space on the memory card, many devices by default turn off audio recording in standby mode. The manufacturer's logic is simple: in the parking lot, conversations in the cabin are usually not conducted, and external sounds are not advisable. However, if the recorder is connected to an external battery or has a permanent plus, this function can sometimes be activated.

Check the parking settings in the app. If there's an Audio Recording option in the Parking Mode section, activate it. Note that recording sound greatly increases the file size. When a motion sensor or impact sensor is triggered in parking mode, the recorder can start writing video with sound, but only at the time of the event. Permanent background recording of audio in the parking lot is not implemented in all models due to firmware limitations.

It's also important to understand the difference between "Time-lapse" and regular recording. In frame-by-frame, sound is usually not written at all, because the frames are taken at a long interval. If it's critical for you to capture sounds around the car in the parking lot, use the standard recording mode with the screen off, if the power source allows, and the energy consumption is higher, but audio control is provided.

💡

In parking mode, the sound is most often turned off by default to save resources, and activation requires a separate setting in the application and stable external power.

Frequently Asked Questions (FAQ)