The modern car DVR is no longer just a camera that captures what is happening on the road. The Xiaomi 70mai Dash Cam Pro Plus A500S is a complex device that requires a competent initial configuration to unlock its full potential. The right setup of recording parameters, impact sensors and wireless modules directly affects the reliability of data storage in a critical situation.
The installation and initial activation process takes no more than fifteen minutes, but requires careful attention to detail. The user needs to properly mount the device on the windshield, connect the power and synchronize the gadget with the smartphone. Ignoring the calibration steps can lead to incorrect operation of intelligent driver assistance systems.
In this guide, we will take a detailed look at each stage of the setup, from physical mounting to subtle software sensitivity adjustment. GPS-module, set up cyclic recording and avoid common errors in operation. Proper preparation of the device ensures that at the right time the video file will be saved and protected from overwriting.
Physical installation and preparation for work
The first step is to properly mount the device on the windshield, and it's important to choose a place that doesn't cover the driver's vision, but provides a wide angle of road capture. A500S It has a compact body, so you can covertly place it behind the rear-view mirror. 3M-tape surface of the glass must be carefully degreased with an alcohol napkin included in the kit.
Power is connected via a Micro-USB or Type-C port (depending on the board revision) using a complete cable. It is not recommended to use third-party cables, as insufficient wire cross section can cause unstable operation at low temperatures. The wiring should be carefully placed in the ceiling and rack skin, using a plastic blade to avoid damage to the cabin elements.
⚠️ Warning: Do not place the power cable near airbags.In the event of a safety system failure, an improperly laid wire may prevent the pillow from opening or be damaged.
Once the device is locked and connected to the on-board network (via a lighter or hardwire kit), the recorder will automatically go into recording mode. The status indicator will flash, signaling the start of operation. If the device does not turn on, check the polarity of the connection in the car or try another power source.
☑️ Ready for installation
Installation of the application and pairing with a smartphone
To fully manage the functionality of Xiaomi 70mai, you need to install a branded mobile application. It is available for Android and iOS platforms in the official Google Play and App Stores. Search should be done by requesting “70mai”, the application icon usually has an orange or gray background with the camera image. Older versions of the software may not support new features, so make sure to download the latest available build.
The pairing process requires you to turn on Bluetooth on your smartphone. Launch an application, register an account (or log in through an existing one), and click the add-on button. In the list of available gadgets, select the Dash Cam Pro Plus+ model. To confirm the connection, you may need to enter a code that is displayed on the registrar’s screen or voice assistant.
The app requests a number of permissions that are critical to the operation: access to geolocation, microphone, storage and Bluetooth. Without geolocation permission, the speed and coordinates on the video will not work, as well as the correct time. Once successfully connected, the application interface will display the current state of the camera and the available settings.
💡
Use a stable Internet connection (Wi-Fi) when you first start the application to quickly load language packs and update the database of speed cameras.
Configuring the video recording parameters
The central element of the configuration is the video menu. This is where you set the parameters that determine the quality and duration of the videos you store. By default, the device is set to write at 1944P resolution (2592×1944) at a frequency of 30 fps. This is the optimal balance between detail and the amount of space occupied on the memory card.
The most important parameter is the duration of a single video file. It is recommended to set a value of 1 min or 3 min. Longer segments make it difficult to find the right moment when viewing, and too short creates an excessive number of files. Cyclical recording should be activated always: it provides automatic overwriting of oldest files when filling out the memory card.
- 📹 Resolution: Choose the maximum available for better readability of numbers.
- 🔄 Cyclicality: mandatory for continuous operation without user intervention.
- 🔊 Audio recording: You can turn off if you don't want to record conversations in the salon.
- 🛡️ WDR: technology of wide dynamic range, improving the picture at dusk.
WDR (Wide Dynamic Range) is a feature that aligns exposure in contrast lighting, such as when leaving a tunnel or at night when oncoming car headlights blind the lens, which can slightly reduce overall brightness during the day, but significantly improve the readability of the numbers at night.
Calibration of ADAS and voice control
The A500S features advanced driver assistance systems known as ADAS (Advanced Driver Assistance Systems), which include Lane Departure Warning and Forward Collision Warning warnings, which require calibration after each installation or removal of the camera.
The calibration process takes about 2-3 minutes and is carried out on a flat road with good markings. In the application menu, you need to select "ADAS Calibration" and follow voice instructions. The car must move at a certain speed so that the camera can capture the position of the lanes and the horizon. Without this procedure, the system will give false positives or not work at all.
⚠️ Note: Do not calibrate. ADAS The system requires movement on the road with visible markings to accurately determine the horizon parameters and future distortions.
Voice control allows you to control the device without distraction from the road. Supported commands in English, Chinese and Russian (depending on the regional version of the firmware); You can ask the recorder to take a picture, turn on the screen or stop recording. Activation of the microphone is done by pressing the corresponding button on the case or by voice command to wake up.
List of voice commands
Work with GPS-memory-card
Built-in GPS-The module is one of the key features of the Plus version, which captures the coordinates, speed and time of movement, overlaying this data on a video sequence, and to activate the function, you need to allow the application to access geodata and wait for the satellites to "cold start" when they first turn on. The process may take up to 5-10 minutes in the open.
Recording quality and stability depend on the memory card. The device supports microSD cards with a volume of 16 to 64 GB (officially), although in practice often work and 128 GB. It is critical to use cards of class U3 or higher with high write speed. Conventional cards quickly fail due to constant overwriting.
| Parameter | Recommended value | Minimum requirement |
|---|---|---|
| Memory capacity | 32-64 GB | 16GB |
| Class speed | U3 / V30 | Class 10 |
| Type of card | High Endurance | Standard |
| File system | FAT32 / exFAT | FAT32 |
Regular maintenance of a memory card involves formatting it directly through the application or menu of the registrar, which prevents file system errors and fragmentation. If the device reports a card error, try formatting it; if the error repeats, replace the media with a new one.
💡
The use of specialized memory cards of the High Endurance series extends the life of the drive by 3-5 times compared to conventional cards for smartphones.
Impact Sensor (G-Sensor) and File Protection
The G-Sensor is responsible for automatically protecting video files when they detect a shock or abrupt braking. When the sensor detects an overload, the current video is marked as overwrite-proof and moved to a separate folder. The sensor sensitivity setting is critical: too high will lead to rapid memory filling with “false” events, too low will lead to loss of important data.
There are three levels of sensitivity available in the app: High, Medium, Low. For urban driving with frequent pits and down-and-coming cops, Low or Medium is the best choice. High is available for the track. There is also the option to completely disable the sensor if you plan to use the recorder, for example, when shooting sports races where overloads are normal.
There is also a manual file protection feature, which is that if you have a dangerous situation on the road, you can press a button on the device body (or use a voice command) to save the current video, which forcefully marks the file as important, and it will not be deleted during cyclic recording until the memory is fully filled.
- 📉 Low sensitivity: suitable for bad roads, fewer false positives.
- 📈 High sensitivity: captures even light touches, but quickly fills up memory.
- 🔒 Manual lock: allows you to save a specific moment on the driver's command.
⚠️ Note: If the memory card is 100% secure, video recording will stop automatically. Check the "Emergency" or "Event" folder regularly and delete unnecessary protected videos.
Update firmware and additional functions
Xiaomi 70mai periodically releases software updates that improve stability and add new features. You can check for an update in the Settings -> About the device section within the application. Update firmware should be carried out only when the smartphone battery is at least 50% charged and the registry network is stable.
The update process takes several minutes to restart, interruption of the process can cause the device to malfunction. After successful installation of the new version, it is recommended to perform a factory reset to eliminate conflicts between old configuration files and the new code.
Among the additional features, you can adjust the time of the screen switch off, save energy and not distract the driver with the display glow at night, and you can also adjust time stamps: the date and time can be displayed on video or hidden, which is important for shooting private areas.