Xiaomi Airdots 2: How to connect the second headphone and restore synchronization

When one of the headphones stops playing sound or working in pairs, it is one of the most common problems of owners of budget acoustics. Users often face the fact that Xiaomi Airdots 2 start to work independently, creating chaos from the sound signals, in which case you need to perform the procedure of forced pairing of the right and left modules between each other.

Before you panic and carry the device to the service center, you should try to perform a software reset. In most cases, the problem is not a physical failure of the speaker or battery, but a failure of the Bluetooth software controller inside the case. The correct sequence of actions allows you to restore the device to work in a few minutes without using special equipment.

In this guide, we will discuss in detail the algorithm of actions that will help you connect the second headphone and return the stereo mode. We will look at the nuances of the indication, features of resetting and methods of solving problems if the standard instruction did not work the first time.

Why the headphones stop working in pairs

The main reason for the desynchronization is the disconnection of the communication between the L and R modules. Wireless headsets of this type use a special protocol, where one headphone (usually the right one) acts as a master device transmitting a signal to the second one. If this communication is broken, the phone sees two devices with the same name, and stereo mode becomes impossible.

A frequent trigger is battery discharge in one of the modules below critical level. When the battery charge drops too low, the power controller may shut down before the correct end of the communication session has been completed. After being placed in the case and then charged, the device may "forget" the partner.

⚠️ Note: If one of the headphones was completely discharged and was in this state for several months, the lithium-ion battery could go into a deep discharge. 30-40 minutes) to accumulate the minimum charge to be switched on.

Problems can also arise after updating the operating system on a smartphone or when connecting to a new signal source.Old pairing profiles in the phone’s memory can conflict with the current state of the headset, requiring the complete removal of old entries from the list of Bluetooth devices.

Preparation for reconnection

The first step before you start any manipulation is to clear your connection history. You need to go to the Bluetooth settings on your smartphone, search the Xiaomi Airdots 2 (or AirDots BASIC 2) list, and select the option “Forget the device” or “Unpair the pairing.” This action is critical, since the phone will stop trying to connect to the unsynchronized modules.

When the device is removed from the list, you need to turn off Bluetooth on the smartphone, which will prevent automatic connection during the setup process, make sure that both headphones are inside the charging case and the indicators are lit in red, indicating the charging process.

• 📱 Remove the device from the Bluetooth list on your phone.
• 📵 Turn off the wireless module on your smartphone.
• 🔋 Place both headphones in the case for charging.
• 🧹 Wipe the contact areas on the headphones and inside the case with dry cloth.

It's important to check the cleanliness of the contact areas. Oxidation or dust on the contacts can prevent full charging, which may prevent one of the modules from turning on when extracted. Use a dry cotton swab or microfiber to clean.

Step-by-step: how to connect the second headphone

The most effective way to restore work is to completely reset to the factory settings (Hard Reset), which causes the headphone controllers to forget all previous connections and re-find each other. First, remove both earphones from the case at the same time. They should automatically turn on.

If the automatic switching hasn't happened, or the lights don't flash, press and hold the touchpads on both headphones for 5-7 seconds. You need to wait for the indicators to flash red. This is a signal that the device is ready to reset.

After the red flash, keep your fingers on the sensors. The reset process takes about 15-20 seconds. At some point, the indicators will go out and then light up again. Release the headphones only after they are completely off (the indicators stop burning).

⚠️ Warning: During the reset procedure, do not put the headphones back in the case. The whole process should take place outdoors, away from sources of severe radio interference.

Now, put the devices back in the case and close the lid for 10 seconds. Then retrieve them. One of the headphones (usually the right one) should start flashing white quickly, waiting for the connection, and the second should flash slowly or not at all, as it will connect to the first one. Now you can turn on Bluetooth on the phone and do a search.

Table of indicators statuses

Understanding color indications helps diagnose the state of the device, and different blinking modes tell the user about the current pairing status or charge level.

Note that the Airdots 2 model has no display and all information is transmitted exclusively through an LED. If you see a constant red glow after being removed from the case, this may indicate a faulty button or a sticking sensor.

Solving problems with desynchronization

Sometimes the standard reset procedure doesn't work the first time, which may be because there's a conflicting profile in the phone's memory. Try resetting again, but this time, after you turn off the headphones (after a red flash), don't put them in the case right away.

Let the devices lie on the table near 10-15 Then simultaneously touch the sensors on both earbuds and hold around 2 They have to find each other, and if one flashes white and the other is off or flashes differently, repeat the reset.

• 🔄 Make sure your phone doesn’t have Bluetooth on during reset.
• 🔇 Disable all other active Bluetooth devices nearby.
• 📶 Get closer to the phone when you re-connect.
• 🔋 Check the charge level of both modules.

In rare cases, switching the master device helps. If the right earbud normally connects to the left, try connecting only the left one to the phone first, and then activating the right one. However, in Xiaomi Airdots 2, the architecture is often rigidly tied to the right channel as the main one.

Features of connecting to different devices

The connection algorithm may vary slightly depending on your smartphone’s operating system. On Android devices, the process usually takes place automatically after reset. On iOS, you sometimes need to manually initiate the connection through settings, even if the headphones are in pairing mode.

If you use a laptop or PC, make sure that the Bluetooth drivers are installed correctly. Older versions of the drivers may not properly handle the A2DP profile used to transmit stereo sound, in which case the computer can see two Airdots 2 devices and try to connect to both as mono headsets.

⚠️ Note: When connecting to Windows, you sometimes need to manually select a sound playback device after pairing, since the system can default to leave the audio output on the laptop speakers.

For owners of Xiaomi equipment and smartphones based on MIUI, there is an advantage in the form of a more stable connection due to the optimization of data protocols, but this does not exclude the need to perform a reset if problems arise.

💡

Useful tip: If you switch between devices often, don't try to connect your headphones to the second gadget without disconnecting them from the first. This causes desynchronization. Always do "Forget the device" on the old gadget.

Frequent Questions and Answers (FAQ)

💡

The main conclusion: 95% of the time, the problem is solved by a full reset (Hard Reset) and re-pairing. If after 3-4 attempts to reset the headphones do not work in pair, perhaps the battery of one of the modules is faulty.