Xiaomi Mi TVs TV They've gained popularity because of a combination of technology and affordable pricing, but even with these devices, sometimes there are situations where the screen is black, the indicator is not responsive, or the TV is not turned on after an upgrade. If you're facing a problem like this, don't panic. 90 percent of the time, the solution is on the surface and doesn't require a service center.
In this article, we will discuss all possible ways to turn on Xiaomi Mi TVs. TV (including the Mi models TV 4S, Mi TV 5, Mi TV Q1 You will learn how to use a physical button, what to do when there is no remote, how to exit standby mode and even how to “resuscitate” the device after a firmware failure, and pay special attention to typical user errors that lead to a lock screen.
Before proceeding to the instructions, make sure that the problem is not due to external factors: check the socket, network cable and signal source (set-top box, cable). HDMI). If the indicator on the TV panel flashes or burns red, this is already a diagnostic signal, which we will also decipher.
1. Standard onset with the remote control
The most obvious way is to use the original Xiaomi Mi Remote, but even here there are nuances that many people don't know about, like if the TV doesn't respond to the first command, it doesn't always mean that it's broken.
Here's a step-by-step algorithm:
- 🔋 Make sure that the remote has working batteries (even if the indicator on the remote is on, the discharge could occur unevenly.
- 📺 Point the remote directly to the IR receiver of the TV (usually located at the bottom of the frame).°. On the Mi models TV 5 Pro receiver hidden behind matte plastic - it's normal.
- 🔄 Press the Power button (⊙) once and wait 5-7 seconds. Some users repeatedly press the button, which leads to a failure of the command.
- 🔴 If the indicator on the TV flashes red, but the screen does not turn on, try holding the Power 10-15 seconds for a forced reboot.
On the Mi models TV Q1 And the newer remote can connect over Bluetooth. If the IR commands don't work, check the pairing:
- Bring the remote to a distance of 10-15 cm to the TV.
- Press the Menu buttons simultaneously + OK 5 seconds.
- Wait for the sound signal or flashing indicator on the remote.
⚠️ Warning: If the remote has previously fallen or been in contact with liquid, its chips may have damaged, and even new batteries won't help, it will require replacement.
2. Powering without remote: button on the body
All Xiaomi Mi TVs TV They have a physical power button that duplicates the functions of the remote, and it depends on the model and year of release:
| Model TV set | Positioning of the button | Type of button |
|---|---|---|
| Mi TV 4A/4S (2018–2020) | Right on the back, under the logo | Mechanical (pressure) |
| Mi TV 5/5 Pro (2020–2022) | Down the center, under the frame. | Touch (touch) |
| Mi TV Q1/Q2 (2021–2023) | Right side, under a plastic stub. | Joystick (press) + scrolling) |
| Mi TV A Pro (2023–2026) | Back left, next to the connectors. HDMI | Combined (pressing) + retention) |
Instructions for use:
- If the button is mechanical, press it once (don't hold it!) on models. 4A forcefulness.
- If the button is touch-sensitive, touch it with one finger for 1-2 seconds. TV 5 The operation is accompanied by a short vibration.
- For joystick (models) Q1/Q2) press the center or hold 3 seconds for forced switching.
If the TV doesn't respond:
- 🔌 Check that the power cable is tightly inserted into the connector. TV 4S connector».
- ⚡ Try another outlet - perhaps the protection machine in the house worked.
- 🔄 Turn off the TV for 1 minute, then try again.
Make sure the TV is connected to the network
Find the button on the table above
Use the correct type of pressing (press/hold)
Check the power indicator after pressing-->
3. Enable via smartphone (Mi Home or Google Home)
If the remote is lost and the button on the case does not work, you can use the mobile application. Xiaomi offers two official ways:
Method 1: Appendix Mi Home
- 📱 Install Mi Home (Android) or App Store (iOS).
- 🔗 Connect your TV and smartphone to the same Wi-Fi network (important!) on Mi models TV Q2 Bluetooth is also supported.
Method 2: Google Home for Android models TV)
- 🤖 Install Google Home.
- 🔄 In the settings of the TV, activate Google Assistant (Settings) → Accounts → Google).
- 🗣️ Say to yourself, OK, Google, turn on Mi. TV» or use the widget in the app.
⚠️ Note: If the TV has not previously been linked to a Mi Account or Google account, remote activation is not possible.
💡
If Mi Home doesn’t find the TV, try resetting the network settings to the TV: go to Settings → Network → Reset the network. Re-sync after rebooting.
4.What to do if the TV is getting stuck and does not turn on
The situation when Xiaomi Mi TV «It freezes on a logo or black screen, typical of a firmware update or third-party application installation:
Step 1: Forced reset
- 🔌 Turn off the power cable from the socket.
- 🕒 Wait 30 seconds (this is important – the capacitors should run out!).
- ⚡ Turn the TV back on and hold the power button for 15-20 seconds.
Step 2: Reset to factory settings (if the reboot didn’t help)
For Android models TV (Mi TV post-2019):
- On the remote, hold the Menu at the same time. + Volume Down for 10 seconds.
- In the Recovery Menu, select Wipe data/factory Reset (use Volume for navigation, OK confirm).
- Confirm the action and wait for the reboot (it will take 3-5 minutes).
For models on PatchWall (Mi) TV 4A/4C):
- Hold the Power button on the case for 20 seconds until the menu appears.
- Select Recovery Mode → Factory Reset.
⚠️ Warning: Reset will delete all installed apps, Wi-Fi settings and accounts.If the TV was tied to Mi Account, reset will require reauthorization.
What if the reset didn't help?
Diagnostics on the nutrition indicator
Color and flashing mode of the LED on the front panel of Xiaomi Mi TV They help you determine the cause of the malfunction:
| Color of indicator | Mode of work | Reason. | Decision |
|---|---|---|---|
| Red (burns constantly) | Standby regime | The TV is off but connected to the network | Press Power on the remote or button on the body |
| Red (blinks 1 time) | Error of nutrition | Problems with the power supply or cable | Check the cable, the socket, try another power source |
| Red (blinks 3 times) | Firmware failure | System partition damaged | Do a reset or stream the TV through USB |
| White (blinks) | Update of the PO | Update installation in progress | Don't turn off the power! Wait until it's finished (up to 30 minutes) |
| Blue (burns constantly) | Working regime | TV's on, but no signal. | Check the source of the signal (HDMI, antenna) |
If the indicator flashes red 5 times in a row, this is a critical error of the motherboard, in which case self-repair is impossible, you need to replace the module in the service center.
On the Mi models TV 5 Pro and newer indicator can change color depending on the condition:
- 🔴 Red: Expectation or Error.
- 🔵 Blue is normal work.
- 🟢 Green – Active Wi-Fi connection (only on Mi) TV Q2).
6.Inclusion after firmware update
Software updates on Xiaomi Mi TV Sometimes it doesn't go smoothly, and the TV can freeze during the installation phase or it won't turn on at all after the reboot:
If the screen is black, but the indicator is white:
- ⏳ Wait 20–30 minutes – the update may have been delayed due to slow internet.
- 🔄 If nothing has changed after the time has elapsed, turn off the power for 1 minute, then turn it on again.
If the TV is cyclically restarted:
- Download the official firmware for your model from the Xiaomi Support website.
- Unpack the archive and copy the file update.zip flash-drive (FAT32).
- Put the flash drive in. USB-TV port (preferably in the USB 2.0 if any).
- Hold the Power button on the case for 10 seconds until the update starts.
⚠️ Note: Do not use flash drives larger than 32 GB – some Mi models TV They don't support large drives. USB 3.0 (blue connectors) – they may not be recognized.
💡
If after updating the TV asks for a password from Mi Account, which you do not remember, use the recovery service. Without authorization, further work of the TV will be blocked.
7. Alternative ways of inclusion
If standard methods don’t work, try these options:
Method 1: Controlling through HDMI-CEC
Function HDMI-CEC It allows you to control the TV through connected devices (set-top box, sound bar:
- Connect to Mi. TV supporter CEC (For example, the Xiaomi Mi Box or NVIDIA Shield).
- Turn on the device – the TV should automatically turn on with it.
- If it does not work, check the settings: Settings → HDMI-CEC → Turn on.
Method 2: Voice control (for models with microphone)
On Mi. TV Q1/Q2 mi TV A Pro has a built-in microphone to turn on the TV with your voice:
- Say, "Hello, Xiao." AI» (For Chinese firmware) or “OK, Google” (for global versions).
- After activating the assistant, say: “turn on the TV”.
Method 3: Remote Enablement via Router
If the TV and router support Wake-on-LAN, you can turn on the TV via the local network:
- Find out. MAC-TV address (located on the back sticker or in network settings).
- Use an app like Wake On Lan (Android/iOS) Or send Magic Packet from PC:
arp -a | find "MAC_ address television"
wakeonlan MAC_ address television💡
On the Mi models TV 5 and later, the Wake-on-LAN function is disabled by default. To activate it, go to Settings → Network → Additionally. → Wake-on-LAN and turn on the option.