How to Turn on Xiaomi Mi TV TV 4S: all ways and solutions to problems

Xiaomi Mi TVs TV 4S are well-deservedly popular due to the combination of affordable prices, high-quality screen and functional firmware Android TV. However, even with such an advanced device, users sometimes have difficulties during the first turn on stage or after a long downtime. This article will help you understand how to start the TV correctly if it does not respond to the remote, how to activate it after updating the firmware, and what to do in unusual situations.

We will look at all possible ways of inclusion, from the classic pressing of a button on the remote to alternative methods through a mobile application or physical buttons on the case. TV 4S 32, 43, 50 and 55" and practical tips for diagnosing problems: If your Suddenly TV stops turning on after a power surge or reset, here's a solution.

Ways to Incorporate Xiaomi Mi TV 4S remotely

The most obvious and common method is to use the original remote control (DU), and even if you've never used a Xiaomi TV before, the switching algorithm is intuitive:

1. Check the batteries. Make sure the remote has working power cells (usually 2 types). AAA). If the batteries are discharged, the indicator on the remote will not light up when you press the buttons.
2. Point the remote to the IR receiver, which is located at the bottom of the TV body (usually under the Mi logo), and the angle of inclination should be no more than 30 degrees.
3. Press the power button. On the original Xiaomi remote, it's marked with a symbol. ○/● (circle with a point inside) and located in the upper left corner.

If the TV doesn’t respond, try the following:

• 🔋 Replace the batteries with new ones (even if the old ones seem to work").
• 📶 Bring the remote as close as possible to the IR receiver (at a distance of 10-15 cm).
• 🔍 Check if there are any obstacles between the remote and the TV (glass, film, decorative panels).
• 📱 Make sure the TV is plugged in and the power indicator (usually red or white) is on or flashing.

If the remote is lost or broken, don't rush to buy a new one. In the next section, we'll tell you how to turn on the TV without it.

Alternative methods of inclusion without remote control

Situations where the remote control is missing or faulty are not uncommon. - Fortunately, Xiaomi Mi TV 4S It's equipped with physical control buttons on the body, and it supports activation via a mobile app.

Method 1: Buttons on the TV body

On the back or side panel of the Mi TV 4S (Depending on the diameter of the model, there are touch buttons or mechanical buttons, and the combination and functionality may vary, but usually they are the same:

• 🔘 Power button – turns the TV on/off.
• 🔽 Volume buttons (Volume) +/–) — Sometimes used to navigate the menu.
• 📺 Source button (Source/Input) — switch HDMI/USB-entrances.

Instructions for inclusion:

1. Find the Power button (usually highlighted in red or icon) ⊙).
2. Press and hold it for 3-5 seconds until the power indicator lights up.
3. If the TV doesn’t respond, try the combination: Power + Volume (hold 10 seconds to reset).

Method 2: Mi Remote (Mi Home)

If physical buttons are not available or not working, use the official Mi Remote app (formerly Mi Home), which allows you to control your TV via Wi-Fi or the IR port of your smartphone.

Connection algorithm:

1. Download the Mi Remote app from Google Play or the App Store.
2. Sign up or sign in to your Xiaomi account (required!).
3. Turn on Wi-Fi on your TV (if it’s turned off, use the buttons on the case to activate the network).
4. In the app, select Add Device → Television → Xiaomi Mi TV 4S.
5. Follow the instructions on the screen for pairing.

Once you've successfully connected, the app will have a virtual remote that's identical to the original one, and the power button is located in the same place, the top left corner.

💡

If the TV is not on Wi-Fi but is plugged in, try using the smartphone’s IR port (if any). Select Infrared Remote mode in the Mi Remote app settings.

What to do if Xiaomi Mi TV 4S left out

If the TV doesn't respond to the remote, the buttons, the app, the reasons can be both software and hardware, and we'll look at some of the most common scenarios and their solutions.

Problem 1: No indication (the light bulb does not burn)

The absence of a light indicator (red or white LED) usually indicates:

• 🔌 Lack of power - check the socket, cable, fork.
• 🔋 Failure of the power supply - if the cable is intact, but the indicator does not burn, there may be a breakdown of the internal PD.
• ⚡ Protection triggered - after a voltage surge, the TV can be blocked.

Actions for diagnosis:

1. Connect the TV to another outlet (preferably with grounding).
2. Try another network cable (use the original one from Xiaomi).
3. Turn off the TV for 10 minutes, then turn it on again (reset the capacitors).

Problem 2: The indicator is on, but the screen is black

If the LED is on or flashing, but the image is missing, the following reasons are possible:

If after all the manipulations the screen remains black, but the indicator works, try a hard reset:

1. Turn off the TV.
2. Press the Power button on the case and, holding it, connect the power cable.
3. Hold the button for 15-20 seconds until the Mi logo appears.

💡

If the TV turns on after reset, but requires adjustment, this is a sign of a software failure. → The device → Data resetting.

Incorporation after firmware or reset update

Updating the software or resetting to factory settings can cause the TV to freeze during the boot phase, in which case turning on requires a special approach.

Scenario 1: The TV is getting stuck on the Mi logo

If after updating the TV turns on, but the logo does not go further:

• 🕒 Wait 10-15 minutes – sometimes the firmware installation process takes time.
• 🔄 Perform Forced Reboot: Press the Power button for 10 seconds.
• 📥 If the problem repeats, download the firmware from the official site and install it through the USB.

Scenario 2: Initial adjustment is required

After resetting, the TV can turn on in First Setup mode.

1. Choose the language (we recommend Russian).
2. Connect to Wi-Fi (required to activate Google services).
3. Sign in to your Xiaomi account or skip this step.
4. Follow the tips of the customization wizard.

If the TV needs to be updated at the setup stage, but cannot install it:

• 🔌 Check your internet connection (try Ethernet cable instead of Wi-Fi).
• 🕘 Make sure the date and time are set correctly (manually or through network synchronization).
• 📁 Download the firmware manually and install through Settings → Update of the PO → Local Update.

Resolving problems with food and power supply

If you want a Xiaomi Mi TV TV 4S It doesn't show signs of life (the indicator doesn't burn, doesn't respond to buttons), the problem can be in the power supply (PD) or the power supply chain.

Signs of malfunction of the power supply

• 🔌 The TV does not turn on from the remote or from the buttons, the indicator does not burn.
• ⚡ When connecting to the network, you can hear cracking or the smell of burning.
• 🔄 The TV spontaneously turns off a few seconds after turning on.
• 💡 The indicator flashes red or orange (PD error code).

For self-diagnosis:

1. Turn off the TV and remove the back cover (if the warranty has expired!).
2. Check the power supply for the presence of swollen capacitors, burnt tracks or the smell of burning.
3. Check the safety lock (usually located near the entrance) 220V).

Check the socket and cable|Examine the PD on the bloated capacitors|Check the fuse (multimeter)|Listen for the presence of cod when switching on-->

If you don't have experience in electronics repair, you should go to a service center, and if you don't know how to replace your PD components, you can short circuit or fire.

What to do if the TV turns off immediately after turning on

This behavior is often associated with:

• 🔥 Overheating - check the fan (on models with active cooling).
• 🔋 PD malfunction - as described above.
• 🖥️ Failure of the motherboard - requires flashing or repair.

Provisional decision:

1. Turn off the TV for 1 hour (full discharge of capacitors).
2. Try to plug it into another outlet (probably the power surge protection works).
3. If the TV turns on for a few seconds and turns off, it's a sign of overheating protection. Let it cool for 2-3 hours.

💡

If the TV turns off due to overheating, make sure the vents on the back are not closed.The distance to the wall must be at least 10 cm.

Frequent User Mistakes and How to Avoid Them

Many problems with the inclusion of Xiaomi Mi TV 4S We've collected the top mistakes and we've given you recommendations on how to avoid them.

⚠️ Warning: Never press the Power button on the TV body for more than 20 seconds in a row.This can result in hardware reset and data loss.

Another common mistake is to ignore the status indicator, and the color and frequency of the LED flashing can tell you a lot about the problem.

• 🔴 Red (constant) - Standby mode.
• 🔴 Red (blinks) – power supply error or overheating.
• ⚪ White (constantly) - TV on.
• ⚪ White (Blinks) – Update firmware or download.

💡

If the light flashes red 3 times in a row, it's a power unit error code. 90% of the time, you need to replace the capacitors or the entire PD.

FAQ: Answers to popular questions