The first launch of a Xiaomi Mi TV or Redmi TV is a process that usually takes only a few minutes, but inexperienced users can be confused by the features of the Android TV interface. Modern models are equipped with complex electronics that require proper power supply and initialization of the system before starting work. If you have just unpacked the device or returned it from transportation, you need to perform a number of preparatory actions that are often forgotten.
In most cases, the problem is not a matrix or board malfunction, but a simple lack of signal or the wrong choice of image source: you need to carefully examine the device body, find hidden controls and make sure that all the cables are connected to the appropriate connectors. The intelligent system will itself tell you next steps, but only after it receives power and signal from the remote or buttons on the case.
This article details the algorithm for turning on the TV, and also offers solutions for situations where the device does not respond to standard commands. We will discuss the remote, physical buttons and hidden menu functions that will help to revive the gadget without calling the wizard.
Primary preparation and feeding
Before looking for the power button, you need to ensure that the power supply is stable.Make sure that the power cable is tightly inserted into the connector on the back of the TV and into the socket.For models with a diagonal of more than 43 inches, Xiaomi recommends using only the original cable, as it has the appropriate cross section to transfer the necessary power.
Notice the status indicator, which is usually located at the bottom of the frame or under the brand logo. If the light bulb is red, then the TV is in standby and ready to turn on.
⚠️ Warning: If the light flashes red or orange when you try to turn on, it may indicate a critical system error or overheating of components.
Some users mistakenly believe that the TV should turn on immediately after the cord is plugged into the socket, in fact, once the voltage is applied, you should give the system a few seconds to self-test, and only then use a remote control or joystick to activate the screen.
💡
Use a network filter with voltage surge protection to connect a Xiaomi TV – this will prolong the life of the electronic unit and prevent malfunctions in the Android TV.
Use of remote control
The main control tool for Xiaomi Mi TV Stick, Box and full-fledged models of the TV P1 series is the remote control. In most modern versions, it works on the Bluetooth protocol, which requires pre-coupling, while classic IR remotes react instantly.
To turn on the TV with a Bluetooth remote, you need to press and hold the center button or button with the image of the house for 3-5 seconds. You will hear a characteristic beep, and the interface animation will appear on the screen. If the remote is new, it can automatically connect when the TV is first turned on via the IR channel, if any.
If the remote does not respond, check the following points:
- 🔋 Make sure the batteries are installed correctly and have sufficient charge.
- 📡 Try to bring the remote closer to the receiver on the TV (usually at the bottom).
- 🔄 Remove and insert the batteries again to reset the connection.
If standard methods don't work, you may have a battery gone down or a software failure of the communication module, and in such cases, you can use the Mi Remote app on a smartphone with an IR port or connected to the same Wi-Fi network to emulate the operation of the physical remote.
Manual activation through buttons on the body
When the remote is lost or discharged, it is not critical, because manufacturers have provided manual control. On Xiaomi and Redmi TVs, buttons are often hidden to preserve the aesthetics of minimalist design. They can be located on the bottom edge, behind in the center or on the side.
Depending on the model, you can control it through a single joystick button or a set of touchpads, you can press down on the joystick or touch the Power touch zone. Some older models require you to hold the button for a few seconds until the screen lights up.
Table of the location of controls on popular models:
| Model TV set | Location of buttons | Type of management | Action for inclusion |
|---|---|---|---|
| Xiaomi Mi TV 4A/4X | Lower face, downtown | Single joystick | Push down |
| Redmi Smart TV X | Back, right. | Physical button | Short press. |
| Mi TV Stick | Absent. | Only remote/USB | Through the remote. |
| Xiaomi TV P1 2021 | Lower face, left | Touch panel. | Touching the icon |
If you can't find the buttons, use a flashlight and look carefully at the perimeter of the case, sometimes the signs are barely visible in bright light, but become visible in the dark or at an angle.
First Launch and Setup of Android TV
Once successfully enabled, you’ll see a welcome screen with an Android TV or PatchWall logo, and the system will suggest choosing an interface language and connecting to a Wi-Fi network.This is a critical milestone, as without the Internet, many of the features of Xiaomi’s smart TV will remain unavailable.
Further, the system may suggest updating the software. It is strongly recommended to agree to the update immediately after the first turn on, as firmware versions may contain bugs that affect the stability of the Wi-Fi module or video decoders.
The initial setup process includes:
- 🌐 Connecting to a home Wi-Fi network (2.4 GHz or 5 GHz).
- 📅 Setting the current date and time (often synchronized automatically).
- 📺 Signing in to Google account to access the Play Market.
☑️ Checklist of first launch
Don’t miss the customization steps, especially those related to location and user agreement. Adjusting the region allows the TV to offer relevant content and work properly with local services.
What to do if the TV is not turned on
If the screen is black after all the manipulations and the indicator is not lit, a diagnosis is needed, often the problem is static electricity or a temporary software failure, which is solved by a full reboot cycle.
Perform the Hard Reset Power procedure: disconnect the TV from the outlet, wait 60 seconds, then press the power button on the case (if any) for 15 seconds without connecting to the network.
⚠️ Note: If the indicator flashes a certain number of times (e.g., 3 or 5 times), this is an error code. Write down the number of blinks and contact technical support as this indicates a specific hardware malfunction.
Also, check the source of the signal. If the TV turns on (the logo burns) but then goes out, it may go into power saving mode due to the lack of active video signal. Try to switch the source manually by pressing the button with the image of the square with the arrow on the remote.
Hidden screen test
Resetting and system restoration
In cases where the Android TV system freezes during the boot phase or does not respond to commands, a Factory Reset may be required, which will delete all user data, accounts and installed applications, returning the TV to the “out of the box” state.
You can reset via the menu if you have access to it: go to Settings → Device → Reset. If the menu is not available, use a combination of buttons on the remote or the case when you turn on. For example, on many models you need to press the confirmation button (OK) and the power switch off at the same time.
Consequences of resetting:
- 🗑️ Removal of all installed applications and data.
- 🔑 Exit from all Google and Xiaomi accounts.
- ⚙️ Return of all system parameters to factory values.
💡
Resetting to factory settings is a radical, but often the only way to programmatically restore the performance of a Xiaomi TV in case of system errors.
Once the reset procedure is complete, the TV will automatically restart and you will have to re-set the initial setup phase described above, ensuring a clean installation without accumulated errors.