How to turn Xiaomi 4A on: Step-by-step guidance and problem solving

When your Xiaomi Redmi 4A suddenly stops responding to the power button, it can be taken by surprise: the screen stays black, the indicators are silent, and it seems that the device has turned into a brick. However, in most cases, the problem is not a fatal motherboard failure, but a software failure or a deep battery discharge.

Before you carry the gadget to the service center, it is worthwhile to conduct a series of self-manipulations. Diagnostics of the condition takes only a few minutes, but avoids unnecessary costs and waiting for repairs. Often, the right keyboard combination or long-term charging is enough to bring the smartphone back to life.

In this article, we will look at all possible scenarios, from trivial discharge to complex cases of system freeze, you will learn how to perform a forced reboot correctly and in which cases it is worth sounding the alarm, carefully follow the algorithm of actions so as not to aggravate the situation.

Primary diagnostics and battery charge check

The most common reason the Redmi 4A doesn’t turn on is because of its critically low charge level, and the lithium polymer batteries in this model tend to go into deep sleep if the voltage drops below a certain point, which is a condition in which the phone may not respond to the charger’s connection immediately.

Leave your smartphone on charge for at least 30-40 minutes, even if the screen doesn't light up. The notification indicator can flash red to signal the energy storage process, or not burn at all. Patience is a key factor in success.

Use only the original cable and power supply, as the Xiaomi 4A is sensitive to current.A tablet charger too powerful or, conversely, a weak USB port of the computer may not start the charging process correctly.

⚠️ Warning: If the phone gets too hot when it's off while charging, disconnect it immediately from the mains.This may indicate a short circuit inside the battery or power controller.

Check the charging connector for dust and pile. Carefully, using a wooden toothpick or plastic spatula, clean the Micro-USB port. The garbage in the connector often interferes with contact, and the energy just doesn't come on board.

💡

Try charging your phone through a computer by plugging it into a USB 2.0 port. Low current sometimes wakes up the power controller better than a powerful fast charge.

Reset (Hard Reset) Reset (Forced Reset)

If the battery is accurately charged, but the screen is black, there was probably a malfunction in the MIUI operating system. The system could hang in a cycling process or go into an incorrect sleep mode, in which case the standard press of the power button will not help, hardware reset is necessary.

Press the on button and the volume button at the same time. Hold them for 10-15 seconds. You should feel a slight vibration, and the Mi logo or the fox repairing the android will appear on the screen, which means that the reboot command was successful.

Sometimes you have to repeat the procedure several times at different intervals. It's important not to release the buttons immediately after the vibration, but to wait for the image to appear. If the phone vibrates but the screen is black, try to increase the brightness, maybe the backlight is just twisted to zero in the software way.

In rare cases, holding only the power button (up to 30 seconds) helps, which breaks the battery power circuit software to simulate its extraction.

Enter Recovery and Fastboot Mode

If a normal reboot doesn’t help, check the availability of service modes. Recovery mode allows you to reset settings to factory or clear the cache, and Fastboot is used to flash the device through the computer.

To log in to Recovery, turn off your phone (if it's responding) and press the power button along with the volume button. When the menu appears, select a language (if available) and try Wipe Data. Remember, this action will delete all your photos and contacts.

Fastboot is activated by pressing the power button and the volume button, and the android repairing bunny or FASTBOOT reading should appear on the screen, and if this mode opens, the display and touchscreen are good and the problem is in the bootloader.

⚠️ Warning: Entering Recovery mode and then resetting the data will completely destroy the information on the internal drive.

Use recovery modes requires caution. If you are not sure about your actions, it is better to limit yourself to trying to log in to Fastboot to check the reaction of the matrix.

Problems with the display and touch screen

There are times when the phone is actually on: it vibrates when calls are made, it makes notification sounds, but the screen remains black. This may indicate a malfunction of the display plume or the matrix itself. Xiaomi 4A is a budget model, and bumps or falls could have gone away contacts.

Try to gently press the top of the screen or bend the case slightly (without fanaticism). If the screen blinks or an image appears, then the problem is poor plume contact, in which case only disassembling and reconnecting the display plume will help.

It's also worth checking if the touchscreen is dead. If the phone is on but doesn't respond to touch, try plugging in an external touchscreen. USB-mouse-wise OTG-If the cursor comes up, it's the sensor, not the system.

Sometimes the brightness of the backlight is dropped to zero by a software failure. Try to shine a flashlight close to the screen in the complete darkness. If you see a barely noticeable image of the interface, then the backlight circuit or its driver has burned.

Using a PC for Diagnostics (ADB and Fastboot)

For advanced users, a great way to check the “liveness” of the device is to connect to the computer. Even if the screen is black, the system can be determined in the Device Manager. You will need Xiaomi USB Driver drivers and ADB utility.

Connect your phone to your PC and start the command line. Type in the adb device command. If a serial numbered device appears on the list, it means the OS is working but it doesn't display the image, which narrows the troubleshooting loop to the display.

If the phone is detected in Fastboot mode, the command for fastboot devices will also show the serial number, which confirms that the processor and memory are functioning normally, in which case you can try to reflash the device through MiFlash.

fastboot flash recovery recovery.img


fastboot reboot

These commands (only if you have experience!) can help you rewrite a damaged partition, but if you are not familiar with the terminal, it is best not to experiment so as not to get a completely non-working brick.

💡

If the computer makes a connection sound USB-When the phone is turned on, the motherboard is alive, and the problem is most likely in the display or software.

When repairs are needed in the service center

There are a number of symptoms that indicate a physical breakdown of components that cannot be eliminated software, and if after all the manipulations the phone does not show signs of life, most likely, the power controller failed or the processor dumped.

Notice the charging indicator, if it doesn't light up at all when you're connected to the grid, or if it burns constantly without blinking, it's a sign of a faulty charge circuit, you need to change the connector or repair the board.

Also alarming is the high heat of the lower part of the case when you try to turn on, this may indicate a short circuit in one of the chips, further attempts to turn on such a device can lead to fire.

If the back cover of the Xiaomi 4A has moved away or the screen is arched, the battery needs to be removed urgently.