The first turn on of any modern gadget is always an exciting moment, especially if we are talking about the popular Xiaomi Redmi 9. Many users are faced with the fact that after removing the device from the box, it does not respond to the press of the power button, which causes panic.
Before you look for defects or bring your phone to the service, you need to perform a number of preparatory steps. Initial activation requires a charge, so the first step should always be to put the device on charge. Use only the original cable and power supply to avoid problems with the charge controller.
The MIUI process that you're running on board has its own unique features that make it different from other Android smartphones. Understanding these nuances will help you avoid unnecessary errors and quickly move to customization. In this article, we'll take a look at everything from connecting to the network to completing the initial setup wizard.
Preparation for the first start of the device
Before you try to activate the Xiaomi Redmi 9, make sure you carefully examine the components. The box must contain the smartphone itself, the charger, the USB Type-C cable, the protective case and the warranty card. The absence of any elements may indicate a violation of the integrity of the package during transportation.
The battery is particularly important, because as mentioned, the battery is only partially charged in the factory, and can run out of charge during storage and delivery, so connecting to the grid is a must before you try to turn it on.
If you see a power connection indication (LED lights up or a battery icon on the screen), it's a process that's started. Leave the phone to charge for at least 15-20 minutes, even if the screen is black. This is the time it takes for the power controller to accumulate the minimum voltage required to start the processor.
💡
Leave your phone charging for 20-30 minutes before first turning on, even if the charge indicator does not light up immediately.
Don't try to turn the device on if it's just been introduced from the cold into a warm room. A sharp temperature difference can cause condensation inside the case, which will lead to a short circuit. Let the gadget lie off at room temperature for about an hour.
Step-by-step instructions for turning on Redmi 9
Once the device is on charge, you can go to the direct start. Find the power button on the right side of the device, which is usually located just above the volume swing and has a characteristic texture or color marking.
☑️ Pre-launch checks
To activate, you need to press the power button and hold it for 3-5 seconds. Don't release the button immediately after the logo appears, wait until the screen lights up completely. In some cases, if the system was updated in the factory, the process may take longer.
If the device is turned on, you will see the Mi logo, replaced by the Redmi logo, and then the MIUI interface will start downloading. At this stage, the system checks the integrity of the files and prepares the components for operation.
Why does the first incorporation take a long time?
In the rare cases where the phone doesn't respond to a short press, you may need to force a reboot, so press the power button and hold it for much longer -- about a few minutes. 10-15 seconds until you feel a vibration or see the logo.
Working with the original setup master
Once launched successfully, you will be taken to the language selection menu, which is the first stage of the setup, where you need to determine the region of use. MIUI supports many languages, including Russian, which makes it easier to continue.
The next step is to connect to a Wi-Fi network. Although you can skip this step and use mobile Internet, it is strongly recommended to connect to a stable wireless network, which is necessary for quick activation of the account and download the latest security updates.
It will prompt you to sign in to your Mi Account or create a new one. Having a Xiaomi account is critical for cloud services, finding a device in case of loss and data synchronization. If you already have an account, just enter your username and password.
Next, you will be able to adjust the biometric protection. Xiaomi Redmi 9 is equipped with a fingerprint scanner located on the back, and the function of unlocking the face, it is recommended to configure both methods for maximum convenience and security of data.
At the end of the setup wizard, you'll be able to recover data from your old device or the cloud, and you can choose to selectively sync your contacts, messages, and photos, and if this is your first smartphone, just skip this step or set up Google services.
Typical startup problems and their solution
Despite the simplicity of the procedure, users sometimes face difficulties, and one of the most common problems is that the phone turns on but hangs on the logo, which can be caused by a failure in the factory firmware process or damage to system files during transportation.
If the screen is on but there is no image (black screen with the phone running), try adjusting the brightness with volume buttons. Sometimes a failure of the display driver causes the backlight not to activate, although the system is working, in which case only resetting the settings through Recovery Mode will help.
The table below shows the main symptoms and possible causes of malfunctions at the start:
| Symptoms. | Possible cause | Method of decision |
|---|---|---|
| The phone doesn't respond to the button. | AKB's deep discharge | Charging with the original 30+ min unit |
| Cyclical reboot | Software or button failure | Log in to Recovery and Reset (Wipe Data) |
| The screen is black, there's vibration. | Display failure | Fixing or repair in the service |
| Request. PUK-code | SIM lockdown | Entering code from the operator |
⚠️ Warning: If the phone is constantly restarting and does not leave the boot cycle, do not try to disassemble it yourself.
Another common situation is the request PUK-The code is immediately after activation. SIM-The card was blocked after multiple incorrect input PIN-Code. PUK You can find on the plastic card, which was included with the SIM card, or get in the personal account of the operator.
Setting up security and accounts
Security is the foundation of working with a smartphone. Once the Xiaomi Redmi 9 is turned on, the system immediately suggests setting up the lock screen. It is recommended to use a complex password or a long pin code, since graphic keys are often too easy to pick up.
Be sure to link the device to a Google account.This will open access to the Google Play Store where you can download apps, and provide backup of contacts and photos in Google Photos. Without this account, the functionality of the smartphone will be severely limited.
Remember to activate Find Device, and if you steal or lose your phone, you can track it, lock it remotely, or erase all data, and it works even if an attacker tries to take it out. SIM-map, if there is Internet.
💡
Mi and Google accounts are the two keys to your digital home: Don't give passwords to third parties and use two-factor authentication.
Also worth paying attention to is app permission settings. MIUI is known for its strict power consumption policy, so it is sometimes required to manually allow apps to run in the background to keep notifications coming on time.
Optimizing the system after switching on
Once you get to the desktop, don't rush to install dozens of apps. First, let the system complete the background optimization processes. In the first 30-60 minutes, the phone may get a little warmer — that's okay, file indexing is going on.
It is recommended to check for system updates immediately. Go to the settings, select About Phone and click on MIUI. Often manufacturers release patches that correct errors discovered after the start of sales of the model.
To extend the life of the battery, adjust the theme and turn off unnecessary animations. Xiaomi Redmi 9 has a design. IPS-It's a screen that reads well, but a bright static picture can use up more charge. Use a dark theme if available.
⚠️ Warning: Do not install applications to "clean up memory" or "accelerate phone" from unverified sources. MIUI They do it better and safer.
The important step is to calibrate the sensor, so if you notice that the screen is not responding correctly, you can run an engineering menu to check. Type ##6484## into your phone to get into the hardware testing menu. Select Touchpanel and run the test.