Modern TVs Xiaomi Smart TV (Mi TV 4A/4S/5/5X/Q1/Q2 Others) offer users not only access to streaming services, but also classic TV broadcasts via on-air, cable or satellite antennas, but many owners face difficulties in first turning on channels: It doesn't find broadcasts, it causes signal errors, or it disappears lists already saved. In this article, we'll look at all the ways to set up TV channels on Xiaomi Smart. TV β From basic automatic search to manual frequency adjustment and solving typical problems.
It is important to understand that the setup process depends on the type of connection: on-air TV (DVB-T/T2), cable (DVB-C) satellite-based (DVB-S/S2). For example, for broadcasting in Russia, support for the standard is required. DVB-T2, For cable, the correct parameters from the provider (symbolic speed, modulation, etc.) will be considered separately, and we will give recommendations on optimizing the channel list and troubleshooting.
Preparing Xiaomi TV for channel search
Before you start setting up, make sure your Xiaomi Smart is yours. TV Physically connected to the signal source:
- π‘ TV: Connect the antenna to the connector RF IN (It's usually on the back (DVB-T2) You may need an active antenna with an amplifier.
- πΊ Cable TV: Use a coaxial cable from the provider. If you have a set-top box, connect it through the service. HDMI.
- π°οΈ Satellite TV: you will need a satellite dish, converter (LNB) And the cable connected to the connector. SAT IN (if the model supports DVB-S2).
Also check the following points:
- π The TV is connected to the network and is in working condition (power indicator is green / blue).
- π If you use a signal amplifier, make sure it is plugged into the socket.
- πΆ For on-air TV, orient the antenna towards the nearest tower (you can find its location on the RTRS website).
If the connection is correct but there is no signal, try:
β οΈ Attention: On Xiaomi Mi models TV P1 newer connector RF IN may be combined with SAT IN. In this case, for terrestrial TV will need an adapter or external tuner.
Automatic channel search on Xiaomi Smart TV
The easiest way to set up channels is to use the built-in auto search feature, which is suitable for most scenarios, as long as the broadcast parameters meet the standards of your region.
- On the remote, press the Menu button (or Settings on new models).
- Go to the Settings section β TV β Channel setting.
- Select Automatic Search.
- Specify the source of the signal: π‘ antenna (DVB-T/T2) β TV-TV; πΊ Cable (DVB-C) β cable-wise; π°οΈ Satellite (DVB-S/S2) β if the plate is connected.
Start
After searching, the TV will save all the channels found in the general list, and you can sort them by number or name in the Channel Management menu.
Is the antenna/cable connected to the connector? RF IN|
The correct signal source is selected (DVB-T2 TV-TV)|
Whether the signal level is sufficient (in the menu "Signal status")|
Is the TV updated to the latest version?-->
On models Xiaomi Mi TV 4A and 4S firmware MIUI TV older than version 3.0, automatic search may miss some channels due to an error in the frequency database).
Manual Channel Configuration: When Automatic Search Fails
If the automatic search is not naΕ‘el If you want to use the channels you want, or if you save them with artifacts (stuttering, no sound), try manual tuning:
- πΆ Weak signal (must manually specify multiplex frequency).
- π Non-standard parameters of the cable provider.
- π°οΈ Satellite TV (transponder data entry required).
Instructions for on-air TV (DVB-T2):
- Go to Settings. β TV β Channel setting β Manual search.
- Choose. DVB-T2 source.
- Enter the multiplex frequency for your region (e.g. 546 MHz for Moscow). Current frequencies can be found on the RTRS website.
- Set the bandwidth β usually 8 MHz.
- Click Search and wait for the result.
For cable TV (DVB-C) need to:
- π Symbolic speed (e.g, 6875 ks/s).
- π’ Modulation (usually 256) QAM).
- π Networked ID (if required by the provider).
If you don't have the data, try the standard values for popular providers:
| Provider | Symbolic speed | Modulation. | Frequency (MHz) |
|---|---|---|---|
| rostelecom | 6875 | 256 QAM | 298, 306, 314 |
| MTS | 6952 | 256 QAM | 322, 330 |
| Beeline | 6875 | 256 QAM | 354, 362 |
| Home. | 6952 | 256 QAM | 290, 370 |
π‘
If you donβt know the cable TV settings, try a full automatic search with Network Search β the TV will scan all possible frequencies, but it will take up to 30 minutes.
Satellite channel configuration (DVB-S/S2)
To watch satellite TV on Xiaomi Smart TV required:
- Satellite dish with converter (LNB).
- Cable connected to the connector SAT IN (Mi models TV Q1/Q2 higher).
- Transponder parameters (frequency, polarization, symbolic speed).
Instructions for setting:
- Go to Settings. β TV β Channel setting β Satellite.
- Select Add Satellite and name it (e.g. Eutelsat) 36E for Tricolor or ABS-2 75E for NTV-Plus").
- Enter the transponder parameters: π‘ Frequency: for example, 12226 MHz for "Tricolor". π Polarization: Horizontal (H) or Vertical (V). πΆ Symbolic speed: 27500 or 43400 (depending on packet).
Search
If the satellite channels are not:
- π Check the plate alignment (signal must be at least 70% in the signal status menu).
- π Make sure the cable is not damaged and connected properly to the LNB.
- π‘ For some satellites (e.g., Yamal) 90E) DiSEqC switch is required.
How to check the signal level from the satellite?
Channel List Management: Sort, Delete, Selected
After successful channel search, their list can be edited:
Channel sorting:
- Go to Settings. β TV β Channel management.
- Choose Change the order.
- Use the buttons. β/β on the remote to move the channel to the desired position.
- Save the changes.
Removal of unnecessary channels:
- ποΈ In the Channel Management menu, select the channel and click Delete.
- π Use Channel Filter for mass removal (e.g., hide all radio stations).
Addendum to the selected:
- β Press the button. OK on the remote while viewing the channel and select Add to your favorites.
- π To switch between your favorite channels, use a button. FAV remote.
On firmware models MIUI TV 4.0 and higher, you can automatically update the channel list to enable it:
- Go to Settings. β TV β Channel setting β Auto-update.
- Set a schedule (for example, once a week).
π‘
Regularly updating the channel list will help avoid problems with lost broadcasts, especially after changes in broadcast networks (for example, when multiplexes move to new frequencies).
Solving Typical Channel Problems on Xiaomi Smart TV
If the channels donβt show, disappear or distort, check the following points:
No signal or "No service":
- π‘ Check the connection of the antenna/cable.
- π Restart the TV (turn off the network for 30 seconds).
- πΆ In the Signal Status Menu, make sure the level is β₯40%. If below, reorient the antenna.
Channels found but do not show:
- π Perform a re-search with the Re-install channels option.
- πΊ Check if Parental Controls are activated (Settings menu) β Security).
- π If there is no sound, check the audio track settings (Settings) β Sound. β Language).
3. the channels disappear after the update:
- π Reset the TV tuner settings: Settings β TV β Reset channel settings.
- π‘ Update the TV firmware: Settings β On TV. β Updating the system.
If the problem persists, try resetting the TV to factory settings (Settings menu) β On TV. β Reset your Wi-Fi network settings and streaming accounts.
β οΈ Attention: On Xiaomi Mi models TV There is no Stick feature for finding air channels, it only works as a media player for streaming.
Additional functions: recording of ether, timeshift and EPG
Xiaomi Smart TVs TV base MIUI TV 3.0 and later support advanced TV broadcasting features:
1.Ether recording (PVR):
- πΌ Connect an external hard drive (format) FAT32/NTFS) port USB.
- π΄ Press while watching. OK on the remote and select Record.
- π Records are saved in a folder PVR on disk and available for viewing in the Media menu.
2.Timesshift (pause live):
- βΈοΈ During viewing, click Pause on the remote.
- π To resume, press Play.
- β οΈ The function only works with the connected USB-accumulator.
Electronic transmission programme (EPG):
- π Press the button. EPG on the remote to see the schedule.
- β° To set a reminder, select the transfer and press OK β Remind me.
On models Xiaomi Mi TV Q2 75" and Mi" TV P1 You can use voice control over a remote with a microphone, for example, you can say "Turn Channel One" or "Find movies on NTV".